2007 YAMAHA YBR250 clock

3-3
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU11872
Tachometer1. Speedometer
2. TachometerThe electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the
tachometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electrical
circuit.
ECA10031
Do not operate the engine in the
tachometer red zone.
Red zone: 10.000 r/min and above
EAUW0150
Multi-function display
Km
RESET
SELECT
TRIP
ODO
1
23
1. Display
2. “SELECT” button
3. “RESET” buttonThe multi-function display is equipped
with the following:l
an odometer (which shows the total
distance traveled)
l
two tripmeters (which show the
distance traveled since they were
last set to zero)
l
a fuel reserve tripmeter (which
shows the distance traveled on the
fuel reserve)
l
a fuel meter
l
a clock
Be sure to turn the key to “ON” before
using the “SELECT” and “RESET”
buttons.Odometer, tripmeter and clock
modes
Pushing the “SELECT” button switches
the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP 1”, “TRIP 2” and the clock mode
in the following order:
ODO
→ TRIP 1 → TRIP 2 → CLOCK →
ODO
If the fuel level warning light comes on
(see page 3-2), the odometer display will
automatically change to the fuel reserve
tripmeter mode “F-TRIP” and start
counting the distance traveled from that
point. In that case, pushing the
“SELECT” button switches the display
between the various tripmeter, odometer
and clock modes in the following order:
F-TRIP → TRIP 1 → TRIP 2 → CLOCK
→ ODO → F-TRIP
To reset a tripmeter, select it by pushing
cap 3.pmd 24/1/2007, 14:37
3

3-4
3
INSTRUMENT AND CONTROL FUNCTIONSthe “SELECT” button, and then push the
“RESET” button for at least one second.
If you do not reset the fuel reserve
tripmeter manually, it will reset itself
automatically and the display will return
to the prior mode after refueling and
traveling 5 km (3mi).
Clock mode
To set the clock:1. Push the “SELECT” button and “RESET” button together for at
least two seconds.
2. When the hour digits start flashing, push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and the minute digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release it to start the clock.
Fuel meter
With the key in the “ON” position, the
fuel meter indicates the amount of fuel
in the fuel tank. The display segments
of the fuel meter disappear towards “E”
(Empty) as the fuel level decreases. When the fuel level reaches the bottom
segment near “E”, the fuel level warning
indicator and the bottom segment will
flash. Refuel as soon as possible.
EAU12347
Handlebar switches1. Pass switch“
”
2. Dimmer switch “
/
”
3. Turn signal switch “
/
”
4. Horn switch “
”1
2
1. Engine stop switch “
/
”
2. Start switch ”
”
cap 3.pmd 24/1/2007, 14:37
4

3-7
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU13021
Fuel tank capTo remove the fuel tank cap
Insert the key into the lock and turn it
1/4 turn clockwise. The lock will be
released and the fuel tank cap can be
removed.
To install the fuel tank cap1. Insert the fuel tank cap into the tank opening with the key inserted
in the lock and with the “
” mark
facing forward.
2. Turn the key counterclockwise to the original position, and then
remove it.
The fuel tank cap cannot be installed
unless the key is in the lock. In addition, the key cannot be removed if the cap is
not properly installed and locked.
EWA10130
Make sure that the fuel tank cap is
properly installed before riding.
EAU13211
Fuel
1
2
1. Fuel tank filler tube
2. Fuel levelMake sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown.
EWA10880
l
l l
l
l
Do not overfill the fuel tank,
otherwise it may overflow when
the fuel warms up and expands.
l
l l
l
l
Avoid spilling fuel on the hot
engine.
cap 3.pmd 24/1/2007, 14:37
7

3-9
3
INSTRUMENT AND CONTROL FUNCTIONS
EAU13800
SeatTo remove the seat1. Insert the key into the seat lock, and then turn it clockwise.
2. Pull the seat off.
1
2
1. Seat lock
2. UnlockTo install the seat
1. Insert the projections on the front of the seat into the seat holders
as shown.
1. Projection
2. Seat holder2. Push the rear of the seat down tolock it in place.
3. Remove the key.Make sure that the seat is properly
secured before riding.
EAU14300
Helmet holder
1
1. Helmet holderThe helmet holder is located under the
seat.
To secure a helmet to the helmet
holder 1. Open the seat. (See page 3-9.)
2. Attach the helmet to the helmet holder, and then securely close the
seat.
EWA10160
Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an accident.
cap 3.pmd 24/1/2007, 14:37
9

6-27
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23780
Replacing the headlight bulbThis model is equipped with a quartz
bulb headlight. If the headlight bulb burns
out, replace it as follows.1. Remove the headlight unit by removing the screws.
1
1. Screw2. Disconnect the headlight coupler,and then remove the bulb cover.
2
1
1. Headlight coupler
2. Bulb cover
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.1.Headlight bulb holder
EWA10790
Headlight bulbs get very hot.
Therefore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.4. Place a new headlight bulb intoposition, and then secure it with
the bulb holder.
ECA10660
Do not touch the glass part of the
headlight bulb to keep it free from oil,
otherwise the transparency of the
glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and
fingerprints on the headlight bulb
using a cloth moistened with alcohol
or thinner.1. Do not touch the glass part of the bulb5. Install the headlight bulb cover, andthen connect the coupler.
6. Install the headlight unit by installing the screws
7. Have a Yamaha dealer adjust the headlight beam if necessary.
cap 6.pmd 24/1/2007, 14:38
27

6-28
6
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24281
Replacing a turn signal light
bulb or the tail/brake light
bulb1. Remove the lens by removing thescrews.
1
1.Screw
1
1. Screw2. Remove the defective bulb bypushing it in and turning it
counterclockwise. 3. Insert a new bulb into the socket,
push it in, and then turn it clockwise
until it stops.
4. Install the lens by installing the screws.
ECA10680
Do not overtighten the screws,
otherwise the lens may break.
EAU37270
Replacing the auxiliary light
bulb
1
1. Auxiliary light bulbIf the auxiliary light bulb burns out,
replace it as follows.1. Remove the headlight unit by removing the screws.
2. Remove the socket (together with the bulb) by pulling it out.
3. Remove the defective bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by pushing it in.
6. Install the headlight unit by installing the screws.
cap 6.pmd 24/1/2007, 14:38
28