Page 41 of 56
DRIVER AIR BAG MODULE
SRS-41
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: 2006 November2007 350Z
CAUTION:
Always work from the side of driver air bag module.
Always place driver air bag module with pad side facing
upward.
Do not insert any foreign objects (screwdriver, etc.) into
driver air bag module.
Do not disassemble driver air bag module.
Do not use old bolts after removal; replace with new bolts.
Do not expose the driver air bag module to temperatures
exceeding 90°C (194°F).
Replace driver air bag module if it has been dropped or sus-
tained an impact.
Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
For installing the air bag module, tighten the TORX bolts (T30).
After the work is completed, perform self-diagnosis to make sure that no malfunction is detected.
Refer to SRS-27, "
SRS Operation Check (USER MODE)" .
PHIA0164E
SBF814E
Page 44 of 56
SRS-44
FRONT PASSENGER AIR BAG MODULE
Revision: 2006 November2007 350Z
FRONT PASSENGER AIR BAG MODULEPFP:K8515
Removal and InstallationNHS0000V
REMOVAL
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
Always work from the side of or under front passenger air bag module.
Do not use air tools or electric tools for servicing.
1. Remove cluster lid C. Refer to IP-14, "
(Q) Cluster Lid C" .
2. Remove instrument passenger panel lower and knee protector (RH). Refer to IP-13, "
(L) Instrument Pas-
senger Panel Lower" .
3. Disconnect passenger air bag module connector.
4. Remove hexagon bolt, and then remove instrument passenger
panel upper assembly.
5. Remove fixing nuts, and then remove front passenger air bag
module.
CAUTION:
Always place front passenger air bag module with caution label side facing upward.
Do not insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
Do not disassemble front passenger air bag module.
Do not use old bolts after removal; replace with new bolts.
Replace front passenger air bag module if it has been
dropped or sustained an impact.
Do not expose the front passenger air bag module to tem-
peratures exceeding 90°C (194°F).
Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
After front passenger air bag module inflates, the instru-
ment panel assembly should be replaced.Passenger air bag module connector : (1)
PHIA1247E
PHIA1248E
SBF814E
Page 46 of 56
SRS-46
SIDE CURTAIN AIR BAG MODULE (FOR COUPE)
Revision: 2006 November2007 350Z
SIDE CURTAIN AIR BAG MODULE (FOR COUPE)PFP:985P0
Removal and InstallationNHS0000W
REMOVAL
CAUTION:
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
Do not use air tools or electric tools for servicing.
1. Remove headlining. Refer to EI-44, "
Removal and Installation (for Coupe Models)" .
2. Disconnect side curtain air bag connector.
3. Remove side curtain air bag module fixing bolts and clip.
4. Remove the side curtain air bag module.
CAUTION:
Always place the side curtain air bag module with the
warning label facing upward.
Do not disassemble side curtain air bag module.
Do not insert any foreign objects (screwdriver, etc.) into
air bag module connector.
Replace side curtain air bag module if it has been
dropped or sustained an impact.
Do not expose the air bag module to temperatures
exceeding 90°C (194°F).
Do not allow oil, grease or water to come in contact with
the side curtain air bag module.
PHIA0660E
1. Side curtain air bag module 2. Clip 3. Bolt
PHIA0171E
SBF814E
