2007 MITSUBISHI LANCER EVOLUTION roof

EXTERIOR -Side Air Dam, Molding and Garnish51-9
SIDE AIR DAM, MOLDING AND GARNISH
REMOVAL AND INSTALLATION
11
ClipClip
Clip
1
Section A – A
Section B – B
Section C – C
Section F – F
Clip2,3
1
Clip
Section D – D
1
2
3 1
Clip
Section E – E
NOTE: Refer to P.51-14 for more information regarding removal and
installation of front deck garnish.
F F
A AB BC CD
D
EE
F
F B
B
B BA
A




Double-sided tape: Generic products: 5mm width, 1.2mm thickness3
AA"1. Roof drip molding
2. Delta outer garnishAB""AA3. Side air dam

EXTERIOR -Side Air Dam, Molding and Garnish51-10
REMOVAL SERVICE POINTS
AA"ROOF DRIP MOLDING REMOVAL
Use the special tool to pry the molding from the rear of the
body for removal.
Caution
Do not use the deformed mold again.
AB"SIDE AIR DAM REMOVAL
1. Attach protection tape all the way along the edges of
the double-sided tape which is still adhering to the body.
2. Use a resin spatula to scrape off the double-sided tape.
3. Peel off the protection tape.
4. Wipe the body surface and clean it with a rag moistened
with isopropyl alcohol.
INSTALLATION SERVICE POINTS
"AASIDE AIR DAM INSTALLATION
Double-sided tape affixing to the side air dam (when
reusing)
1. Scrape off the double-sided tape with a resin spatula
or gasket scraper.
2. Wipe off the side air dam adhesion surface and clean
it with a shop towel moistened with isopropyl alcohol.
3. Affix the specified double sided tape to the side air dam.
(Refer to P.51-9.)
MB990449
Protection tape
Double-sided tape

54A-3
SIDE TURN-SIGNAL LAMP 31............
SPECIAL TOOL 31............................
SIDE TURN-SIGNAL LAMP 31..................
ROOM LAMP 31.........................
TROUBLESHOOTING 31.......................
REAR COMBINATION LAMP 32...........
SPECIAL TOOL 32............................
TROUBLESHOOTING 32.......................
REAR COMBINATION LAMP 32................
HIGH-MOUNTED STOP LAMP 34.........
ON-VEHICLE SERVICE 34......................
High-mounted Stop Lamp Bulb Replacement 34.
HIGH-MOUNTED STOP LAMP 34................
LICENCE PLATE LAMP 35...............
ON-VEHICLE SERVICE 35.....................
License Plate Lamp Replacement 35...........
LICENCE PLATE LAMP 35.....................
HAZARD WARNING LAMP SWITCH 36....
SPECIAL TOOL 36............................
HAZARD WARNING LAMP SWITCH 36.........
HORN 37................................
CIGARETTE LIGHTER 37.................
COLUMN SWITCH 38....................
SPECIAL TOOL 38............................
COLUMN SWITCH 38..........................
CLOCK 40...............................
SPECIAL TOOL 40............................
CLOCK 40....................................
POLE ANTENNA 41......................
ROOF ANTENNA 42......................
DEFOGGER 42...........................
TROUBLESHOOTING 42......................
ON-VEHICLE SERVICE 43.....................
Printed Heater Check 43......................
Defogger Relay Continuity Check 43...........
DEFOGGER SWITCH 43.......................

CHASSIS ELECTRICAL -Roof Antenna/Defogger54A-42
ROOF ANTENNA
REMOVAL AND INSTALLATION
pre-removal and Post-installation Operations
DFront Pillar trim, Rear Pillar Trim and Lower/Upper Center Pillar Trim Removal and Installation (Refer to GROUP 52A -
Trims.)
DAssist Step Removal and Installation (Refer to GROUP 52A - Head Lining.)
DFront Room Lamp and Rear Room Lamp Removal and Installation
DHead Lining Removal and Installtion (Refer to GROUP 52A - Head Lining.)
1
2
3
Removal steps
1. Antenna pole
2. Roof antenna base
DInstrument panel (Refer to GROUP
52A - Instrument Panel.)3. Antenna feeder cable
DEFOGGER
TROUBLESHOOTING
Refer to GROUP 55.