2007 MITSUBISHI LANCER EVOLUTION oil type

ENGINE ELECTRICAL -Ignition System16-28
ON-VEHICLE SERVICE
IGNITION COIL (WITH BUILT-IN POWER
TRANSISTOR) CHECK
Check by the following procedure, and replace if there is
a malfunction.
SECONDARY COIL RESISTANCE CHECK
Measure the resistance between the high-voltage terminals
of the ignition coil.
Standard value: 8.5 - 11.5 kΩ
PRIMARY COIL AND POWER TRANSISTOR
CONTINUITY CHECK
NOTE
1. An analogue-type circuit tester should be used.
2. Connect the negative ( - ) prove of the circuit tester to
terminal 1.
Caution
This test must be performed quickly (in less than 10
seconds) to prevent coil from burning and power
transistor from breakage.
1.5V power across 2 - 3Continuity across 1 - 2
When energizedYe s
When not energizedNo
RESISTIVE CORD CHECK
Measure the resistance of the all spark plug cables.
1. Check cap and coating for cracks.
2. Measure resistance.
Limit: Max. 22 kΩ

MANUAL TRANSMISSION -General/General Information/
Service Specification/Lubricants22A-3
GENERAL
OUTLINE OF CHANGE
With the addition of the EVOLUTION-VII, the W5M51 transmission service adjustment procedure has
been set as follows.
GENERAL INFORMATION
ItemsSpecifications
GradeRS, RS IIRS, RS II (With super cross gear)
Transmission modelW5M51
Engine model4G63-DOHC-T/C
Type5-speed, floor-shift
Gear ratio1st2.7852.785
2nd1.9501.950
3rd1.4071.444
4th1.0311.096
5th0.7200.825
Reverse3.4163.416
Final reduction ratio
(Differential gear ratio)4.5294.529
Front limited-slip differential
(Helical-gear type)Not providedProvided
TransferReduction ratio3.3073.307
Limited-slipdifferentialVCU or hydraulic multi plate
clutch (ACD)VCU or hydraulic multi plate
clutch (ACD)
SERVICE SPECIFICATION
ItemStandard value
Hydraulic unit generation oil pressureMPa1.0 - 1.6
LUBRICANTS
ItemSpecified lubricantQuantity L
Transmission oilGear oil SAE 75W-90 or 75W-85W conforming to API GL-42.8
Transfer
oilVehicles without ACD or ve-
hicles without ACD and AYCMITSUBISHI Genuine Gear Oil Part No.8149630 EX,
CASTROL HYPOY LS (GL-5, SAE 90), SHELL-LSD
(GL 5SAE80W90)orequivalent
0.55
Vehicles with ACD or vehicles
with ACD and AYC(GL-5, SAE 80W - 90) or equivalent0.6
FluidPiping between ACD and
hydraulic unitDIA QUEEN ATF SP III0.9
Pipes between ACD and hy-
draulic unit and between AYC
and hydraulic unit1.0

MANUAL TRANSMISSION OVERHAUL -Control Housing22B-41
DISASSEMBLY SERVICE POINT
AA"LOCK PIN REMOVAL
Tap out the lock pin from the direction shown in the illustration.
REASSEMBLY SERVICE POINTS
"AANEEDLE BEARING INSTALLATION
Press the needle bearing into the dimensions shown in the
illustration so that the type stamp side faces the indicated
direction.
"BAOIL SEAL INSTALLATION
Apply transmission oil on the oil seal lip section.
Transmission oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN” multi gear oil
<75W/85W> or equivalent
"CAAIR BREATHER INSTALLATION
(1) Apply sealant on the periphery of the insertion section.
Sealant
Specified sealant:
3M SUPER WEATHERSTRIP No.8001 or
equivalent
(2) Install so that the protrusion faces the direction shown
in the illustration.
Lock pin
Control
finger
Control
housing
Needle
bearing
2mm Type
stamp
side

MANUAL TRANSMISSION OVERHAUL -Transmission Case22B-47
"BANEEDLE BEARING INSTALLATION
Press in to the flush with the type stamp side facing the
direction shown in the illustration.
"CAOIL SEAL INSTALLATION
(1) Apply transmission oil on the oil seal lip section.
Transmission oil
Specified oil:
MITSUBISHI genuine “DIA-QUEEN” multi gear
oil <75W/85W> or equivalent
(2) Using the special tool, install the oil seal onto the
transmission case.
Bush
3mm
Needle bearing
Type stamp side
MD998800

PROPELLER SHAFT -General Information/Service Specification/
Lubricant/Sealant/Special Tool25-2
GENERAL INFORMATION
3 way split 4-joint type propeller shaft with center bearing is adopted.
SERVICE SPECIFICATION
ItemsStandard valueLimit
Propeller shaft runout mm-0.5
LUBRICANT
ItemsSpecified lubricantQuantity
Front propeller shaft sleeve
yokeHypoid gear oil SAE 75W-90 or 75W-85W or 80W
conforming to API GL-4As required
LJ assemblyRepair kit grease75±5g
SEALANT
ItemsSpecified sealantsRemarks
LJ assembly rubber packing3M Stud Locking 4170 or equivalentAnaerobic sealant
SPECIAL TOOL
ToolNumberNameUse
MB998801Bearing removerRemoval of the center bearing assembly

REAR AXLE -General Information27B-2
GENERAL INFORMATION
The rear axle consists of rear hubs, wheel bearings,
drive shafts, and rear differential and, it has the
following features.
DThe wheel bearing is a unit bearing (double-row
angular contact ball bearing).
DThe drive shaft incorporates B.J.-T.J. type
constant velocity joints with high transmission
efficiency and low vibration and noise.DABS rotors for detecting the wheel speeds are
press-fitted to the B.J. outer wheels in vehicles
with ABS or ACD.
NOTE
1. B.J.: Birfield Joint
2. T.J.: Tripod Joint
SPECIFICATIONS
ItemVehicles without AYCVehicles with AYC
Wheel
bearingsWheel bearing typeUnit bearing (Double-row angular contact ball
bearing)
g
Bearing (outside diameter×inside diameter) mm78×40
Drive
shaft
Joint typeOutsideB.J.
shaftInsideT.J.
Shaft length*1×Shaft diameter
mm
Left483×25426×25
mmRight573×25446×25
NOTE
*1: The shaft length indicates the length between the center points of each joint.
STRUCTURAL DIAGRAM
Oil sealRear hub Differential carrier
B.J.
Drive shaftT. J .

REAR AXLE -Differential Carrier 27B-45
"BADRIVE PINION REAR BEARING OUTER RACE
PRESS-FITTING
"CADRIVE PINION FRONT BEARING OUTER RACE
PRESS-FITTING
"DADRIVE PINION HEIGHT ADJUSTMENT
Adjust the drive pinion height by the following procedures:
1. Apply multipurpose grease to the washer of special tool.
2. Install special tool and drive pinion front and rear bearing
inner races to the gear carrier in the sequence shown
in the illustration.
3. Tighten the nut of special tool a little at a time while
measuring the turning torque of the drive pinion. Then
confirm the turning torque (without the oil seal) is at the
standard value.
Standard value:
Bearing typeTurning torque
New0.88 - 1.17 N·m
Caution
Take care not to fit gear oil on the bearing.
NOTE
The special tool can not rotate, move several times in
moving area, after rotating the bearing, measure the
torque.
MB990938
MB990935
MB990938
MB990932
MB990836
(MB990835)
MB990836
MB990326 MB990685
MB990836

REAR AXLE -Differential Carrier 27B-47
3. Measure the drive pinion turning torque (without the oil
seal).
Standard value:
Bearing divisionTurning torque
New0.88 - 1.17 N·m
Caution
Take care not to fit gear oil on the bearing.
4. If the drive pinion turning torque is not within the standard
value, adjust the turning torque by replacing the drive
pinion front shim(s) or the drive pinion spacer.
NOTE
When selecting the drive pinion front shims, if the number
of shims is large, reduce the number of shims to a minimum
by selecting the drive pinion spacers.
Also, select the drive pinion spacer from the following
two types.
Height of drive pinion spacer mmIdentification colour
57.72-
57.08Red
5. Remove the companion flange and drive pinion again.
Then insert the drive pinion front bearing inner race into
the gear carrier. Use special tool to press-fit the oil seal.
6. Install the drive pinion assembly and companion flange
with mating marks properly aligned. Tighten the
companion flange self-locking nut to the specified torque
using special tool.
MB990326
MB990685
Identification
colour
MB990727
MB990850
186±29 N·m