2007 KIA CARNIVAL belt

B1529Passenger Airbag Deactivation Switch Defect
B1530 Passenger Airbag Deactivation Switch Instability
B1620 Supplemental Restraint System Control Module Internal Fault (Replace SRSCM)
B1650 Crash Recorded - Frontal (Replace SRSCM)
B1651 Crash Recorded - Driver Side (Replace SRSCM)
B1652 Crash Recorded - Passenger Side (Replace SRSCM)
B1655 Crash Recorded - Passenger Side with PAB inhibited (Replace SRSCM)
B1657 Crash Recorded - Belt Pretensioner Only
B1658 Belt Pretensioner 6 times Deployment (Replace SRSCM)
B1701 Buckle Pretensioner [Front- Driver] Resistance Too High
B1702 Buckle Pretensioner [Front- Driver] Resistance Too Low
B1703 Buckle Pretensioner [Front- Driver] Resistance Circuit Short to Ground
B1704 Buckle Pretensioner [Front- Driver] Resistance Circuit Short to Battery
B1706 Buckle Pretensioner [Front- Passenger] Resistance Too High y
B1707 Buckle Pretensioner [Front- Passenger] Resistance Too Low
B1708 Buckle Pretensioner [Front- Passenger] Resistance Circuit Short to Ground y
B1709 Buckle Pretensioner [Front- Passenger] Resistance Circuit Short to Battery
B1722 Curtain Airbag [Rear- Driver] Resistance too High
B1723 Curtain Airbag [Rear- Driver] Resistance too Low
B1724 Curtain Airbag [Rear- Driver] Circuit short to Ground
B1725 Curtain Airbag [Rear- Driver] Circuit short to Battery
B1726 Curtain Airbag [Rear- Passenger] Resistance too High
B1727 Curtain Airbag [Rear- Passenger] Resistance too Low
B1728 Curtain Airbag [Rear- Passenger] Circuit short to Ground
B1729 Curtain Airbag [Rear- Passenger] Circuit short to Battery
B2500 SRS Warning Lamp Fault
B2505 Passenger Airbag Deactivation Lamp Fault

2007 > 2.7L V6 GASOLINE >
AIRBAG DISPOSAL
SPECIAL TOOL REQUIRED
Before scrapping any airbags or side airbags (including those in a whole vehicle to be scrapped), the airbags or side
airbags must be deployed. If the vehicle is still within the warranty period, before deploying the airbags or side airbags,
the Technical Manager must give approval and/or special instruction. Only after the airbags or side airbags have been
deployed (as the result of vehicle collision, for example), can they be scrapped.
If the airbags or side airbags appear intact (not deployed), treat them with extreme caution. Follow this procedure.
DEPLOYING AIRBAGS IN THE VEHICLE
If an SRS equipped vehicle is to be entirely scrapped, its airbags or side airbags should be deployed while still in the
vehicle. The airbags or side airbags should not be considered as salvageable parts and should never be installed in
another vehicle. 1. Turn the ignition switch OFF, and disconnect the battery negative cable and wait at least three minutes.
2. Confirm that each airbag or side airbag is securely mounted.
3. Confirm that the special tool is functioning properly by following the check procedure.
DRIVER'S AIRBAG :
1.Remove the driver's airbag and install the SST(0957A - 38500).
2. Install the driver's airbag on the steering wheel.
FRONT PASSENGER'S AIRBAG :
1.Remove the glove box, then disconnect the 2P connector between the front passenger's airbag and SRS main
harness.
2. Install the SST(0957A - 3F100).
SIDE AIRBAG :
1.Disconnect the 2P connector between the side airbag and side wire harness.
2. Install the SST (0957A- 3F100).
CURTAIN AIRBAG :
1.Disconnect the 2P connector between the curtain airbag and wire harness.
2. Install the SST(0957A - 38500).
SEAT BELT PRETENSIONER :
1.Disconnect the 2P connector from the seat belt pretensioner.
2. Install the SST(0957A - 38500).
3. Place the deployment tool at least thirty feet (10 meters) away from the airbag.
4. Connect a 12 volt battery to the tool.
5. Push the tool's deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud
noise and rapid inflation of the bag, followed by slow deflection)
6. Dispose of the complete airbag. No part of it can be reused. Place it in a sturdy plastic bag and seal it securely.

Seat Belt Pretensioner (BPT)

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
The Seat Belt Pretensioners (BPT) are installed inside Center Pillar (LH & RH). When a vehicle crashes with a certain
degree of frontal impact, the pretensioner seat belt helps to reduce the severity of injury to the front seat occupants by
retracting the seat belt webbing. This prevents the front occupants from thrusting forward and hitting the steering
wheel or the instrument panel when the vehicle crashes.
Never attempt to measure the circuit resistance of the Seat Belt Pretensioner (BPT) even if you are using the
specified tester. If the circuit resistance is measured with a tester, the pretensioner will be ignited accidentally.
This will result in serious personal injury.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2. Remove the door scuff trim. (Refer to BD group)
3. Remove the center pillar trim. (Refer to BD group)
4. Remove the lower anchor bolt.
5. Remove the upper anchor bolt.
6. Loosen the Seat Belt Pretensioner mounting bolts and remove the Seat Belt Pretensioner.
7.Disconnect the Seat Belt Pretensioner connector.
INSTALLATION
1.Disconnect the negative ( - ) cable from battery and wait for at least three minutes.
2. Remove ignition key from the vehicle.
3. Connect the Seat Belt Pretensioner connector.
4. Install the Seat Belt Pretensioner (BPT) with bolts.
Tightening Torque (Seat Belt Anchor Bolt)
: 4.0 ~ 5.5 kgf.m (39.2 ~ 53.9 Nm, 28.9 ~ 39.8 lb.ft)
5. Install the upper and lower anchor bolts.
Tightening Torque (Seat Belt Anchor Bolt)
: 4.0 ~ 5.5 kgf.m (39.2 ~ 53.9 Nm, 28.9 ~ 39.8 lb.ft)
6. Install the center pillar trim and door scuff trim.
7. Reconnect the negative battery cable.
8. After installing the Seat Belt Pretensioner (BPT), confirm proper system operation:
a. Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

Seat Belt Buckle Pretensioner

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
The Seat Belt Buckle Pretensioners (BUPT) are installed in the right side of the driver seat and the left side of the
passenger seat. When a vehicle crashes with a certain degree of frontal impact, the seat belt buckle pretensioner
helps to reduce the severity of injury to the front seat occupants by retracting the seat belt buckle. This prevents the
front occupants from thrusting forward and hitting the steering wheel or the instrument panel when the vehicle crashes.
Never attempt to measure the circuit resistance of the Seat Belt Buckle Pretensioner (BUPT) even if you are
using the specified tester. If the circuit resistance is measured with a tester, the pretensioner will be ignited
accidentally. This will result in serious personal injury.

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2. Remove the front seat assembly. (Refer to BD group)
3. Loosen the Seat Belt Buckle Pretensioner mounting bolt and remove the Seat Belt Buckle Pretensioner.
INSTALLATION
1.Disconnect the battery negative cable and wait for at least three minutes.
2. Remove the ignition key from the vehicle.
3. Install the Seat Belt Buckle Pretensioner (BUPT) with the bolt.
Tightening torque
: 4.0 ~ 5.5 kgf.m (39.2 ~ 53.9 Nm, 28.9 ~ 39.8 lb.ft)
4. Install the front seat assembly.
a.Ensure that the harness is installed and routed properly to prevent damage to the wiring.
5. Reconnect the battery negative cable.
6. After installing the Seat Belt Buckle Pretensioner (BUPT), confirm proper system operation:
a. Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.