Page 40 of 1575
18.Remove the camshaft bearing cap(A).
19.Remove the timing chain tensioner(A).
20.Remove the camshaft.
21. Remove the bank 2 timing belt rear cover(A).
22.Remove the bank 1 timing belt rear cover(A).
Page 46 of 1575
7.Using the SST(09214- 21000), install the camshaft oil seal.
a.Befor installing, apply engine oil.
b. The camshaft cap surface should adhere to the cylinder head assembly.
c. Do not press an eccentric load.
8. Install the CKP sensor connector bracket(A).
9.Install the bank 1 timing belt rear cover(A).
10. Install the bank 2 timing belt rear cover(A).
Page 47 of 1575
The length of the bolt(B) is longer than that of the bolt(C).
11. Install the timing belt.(Refer to 'Timing system').
12. Check and adjust the valve clearance.
13. Install the cylinder head cover.
(1) Remove oil, dust or sealant on the upper surface of the cylinder before assembling cylinder head cover.
(2) Assemble the cylinder head cover in five minites after applying liquid gasket(LOCTITE 5900) on the camshaft
cap and packing part.
(3)Tighten the cylinder head cover bolts as following order(A).
Tightening torque
7.8~9.8Nm(0.8~1.0kgf.m, 5.8~7.2lb- ft)
Page 48 of 1575
a.Do not start engine for thirty minites after assembling the cylinder head cover.
b. Do not reuse the cylinder head cover gasket.
14. Install the water temp. control assembly.
15. Install the intake manifold assembly.
16. Install the exhaust mainfold assembly.
17. Install the power steering pump.(Refer to 'ST' group).
18. Install the drive belt(A).
19.Install the heater hose.
20. Connect the brake vaccume hose(A).
21.Install the PCV(Pulge Control Valve) hose(A).
22.Connect the engine wiring harness connectors.
(1) Connect the bank 1 CMP sensor connector(A).
Page 75 of 1575
2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Remove the drive plate(A).
2.Remove the rear plate(A).
3.Remove timing belt.
4. Remove intake manifold.
5. Remove exhaust manifold.
6. Remove generator from engine.(Refer to 'ST' group).
7. Remove power steering pump from engine.(Refer to 'HA' group).
8. Remove cylinder head.
9. Remove A/C compressor from engine.(Refer to 'EE' group).
10. Remove water pump assembly.
INSTALLATION
1.Install the water pump.
2. Install the air conditioning compressor.(Refer to 'HA' group).
3. Install the cylinder head.
4. Install the power steering pump.(Refer to 'ST' group).
5. Install the generator.
6. Install the intake manifold.
7. Install the exhaust manifold.
8. Install the timing belt.
9. Install the rear plate(A).
Tightening torque
Page 92 of 1575
Piston pin- to- connecting rod interference
- 0.033 ~ - 0.016mm ( - 0.0013 ~ - 0.0006in.)
REASSEMBLY
a.Thoroughly clean all parts before reassembling.
b. Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
c. Replace all gaskets, O - rings and oil seals with new parts.
1. Assemble the piston and the connecting rod.
(1) Use a hydraulic press for installation.
(2) The piston front mark(A) and the connecting rod front mark must face the timing belt side of the engine.
2.Install piston rings.
(1) Install the oil ring spacer and 2 side rails by hand.
(2) Using a piston ring expander, install the 2 compression rings with the code mark facing upward.
(3) Position the piston rings so that the ring ends are as shown.
3.Install the connecting rod bearings.
(1) Align the bearing(A) claw with the groove of the connecting rod or connecting rod cap(B).
(2) Install the bearings(A) in the connecting rod and connecting rod cap(B).
Page 103 of 1575
2007 > 2.7L V6 GASOLINE >
REMOVAL
WATER PUMP
1. Drain the engine coolant.
System is under high pressure when the engine is hot. To avoid danger of releasing scalding engine coolant,
remove the cap only when the engine is cool.
2. Remove drive belt(A).
3.Remove the timing belt.
4. Remove the water pump(A) and gasket(B).
WATER TEMPERATURE CONTROL ASSEMBLY
1.Drain the engine coolant.
2. Remove the air cleaner assembly.
3. Disconnect the radiator upper and lower hose(A, B).
Page 108 of 1575
Clean the contacting face before assembling.
2. Install the timing belt.
3. Install drive belt(A).
4.Fill with engine coolant.
5. Start engine and check for leaks.
6. Recheck engine coolant level.
WATER TEMPERATURE CONTROL ASSEMBLY
1.Install the water pipe(A).
Tightening torque
16.7 ~ 19.6Nm (1.7 ~ 2.0kgf.m, 12.3 ~ 14.5lb- ft)
2.Install the water temperature control assembly(A) with a new gasket(B).
Tightening torque