2007 KIA CARNIVAL engine

Ensure the LH/RH classification of the cylinder head gasket when installing.
2. Tighten the cylinder head bolts with the plain washers in several steps as following order.
a.In assembling washers, the marked surface should face upward.
b. In installing the cylinder head bolts, apply engine oil on the thread of the bolts and the surface of the
washers.
Tightening torque
22.6~26.5Nm(2.3~2.7kgf.m, 16.6~19.5lb - ft) + (60° + 2°) + (45° + 2°)
Using the SST(09221- 4A000), tighten the bolts which need to be tightened with the angular tightening method.
3. Install the CVVT assembly and camshaft chain sprocket with the dowel pin in the CVVT installed to the intake
camshaft. Ensure that the pin will not be installed in the hole for oil feeding.

7.Using the SST(09214- 21000), install the camshaft oil seal.
a.Befor installing, apply engine oil.
b. The camshaft cap surface should adhere to the cylinder head assembly.
c. Do not press an eccentric load.
8. Install the CKP sensor connector bracket(A).
9.Install the bank 1 timing belt rear cover(A).
10. Install the bank 2 timing belt rear cover(A).

a.Do not start engine for thirty minites after assembling the cylinder head cover.
b. Do not reuse the cylinder head cover gasket.
14. Install the water temp. control assembly.
15. Install the intake manifold assembly.
16. Install the exhaust mainfold assembly.
17. Install the power steering pump.(Refer to 'ST' group).
18. Install the drive belt(A).
19.Install the heater hose.
20. Connect the brake vaccume hose(A).
21.Install the PCV(Pulge Control Valve) hose(A).
22.Connect the engine wiring harness connectors.
(1) Connect the bank 1 CMP sensor connector(A).

(2)Connect the breather hose(B) from air cleaner hose.
(3) Connect the MAF connector(A).
26. Install the engine cover.
27. Refill engine coolant.
DISASSEMBLY
Identify MLA(Mechanical Lash Adjuster), valves and valve springs as they are removed so that each item can be
reinstalled in its original position.
1. Remove MLA(Mechanical Lash Adjuster)s(A).
2.Remove valves.
(1) Using SST(09222- 3K000, 09222 - 3C300), compress the valve spring and remove retainer lock.
(2)Remove the spring retainer.
(3) Remove the valve spring.
(4) Remove the valve.

REASSEMBLY
a.Thoroughly clean all parts to be assembled.
b. Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
c. Replace oil seals with new ones.
1. Install valves.
(1) Using SST(09222- 22001), push in a new valve stem seal with applying engine oil.
a.Do not reuse old valve stem seals.
Incorrect installation of the seal could result in oil leakage past the valve guides.
b. Reassemble the valve stem seals
(2) After applying engine oil on the outer surface of each valve stem, insert the valve in the valve guide.
Install the valve, valve spring and spring retainer.
When installing valve springs, the side coated with enamel should face toward the valve spring retainer
(3) Using the SST(09222 - 3K000, 09222 - 3C300), compress the springs and install the retainer locks. After
installing the valves, ensure that the retainer locks are correctly in place before releasing the valve spring
compressor.

(4)Lightly tap the end of each valve stem two or three times with the wooden handle of a hammer to ensure
proper seating of the valve and retainer lock.
2. Install MLAs with engine oil applied on its surface.
Check that the MLA rotates smoothly by hand.
MLA should be reinstalled in its original position.
3. Install OCV(Oil Control Valve)(A).
Tightening torque
7.8 ~ 9.8Nm(0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb - ft)
a.To install OCV with gray colored connector into RH bank.
b. To install OCV with black colored connector into LH bank.

a.Do not reuse the OCV when dropped.
b. Keep clean the OCV.
c. Do not hold the OCV sleeve during servicing.
d. When the OCV is installed on the engine, do not move the engine while holding the OCV yoke.
e. If there is dust on the filter(B) of the OCV, clean it all.

Engine And
Transaxle Assembly