2007 KIA CARNIVAL oil

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
Oil Temperature Sensor
The oil temperature sensor is of the thermistor type, and senses the automatic transaxle fluid temperature. Using the
signal from this sensor, TCM(PCM) controls the shift pattern optimally during shift. In order to operate the damper
clutch, this signal is also referred.
- Range of temperature : - 40°C~145°C
- Type: Separated type (High / Low temperature)
- Standard value of internal resistance
Temp.[°C(°F)] Resistance(kΩ) Temp.[°C(°F)]Resistance(kΩ)
- 40(- 40) 139.580(176) 1.08
- 20(- 4) 47.7100(212) 0.63
0(32) 18.6120(248) 0.38
20(68) 8.1140(284) 0.25
40(104) 3.8160(320) 0.16
60(140) 1.98

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the automatic transaxle assembly.
2. Remove the valve body cover(refer to the overhaul manual).
3. Disconnect the oil temperature sensor connector.
4. Remove the oil temperature sensor(B), loosening the mounting bolt(A).
5.Replace the sensor with the new one and reassemble the rest of the parts.
INSPECTION
1.Remove the oil temperature sensor(A).
2.Measure the resistance between the terminal 1 and 2 of the sensor connector.
Temp.[°C(°F)] Resistance(KΩ)
0(32)
100(212) 18.6
0.63
3.
If the value is out of the specfication, replace the oil temperature sensor.

2007 > 2.7L V6 GASOLINE >
SPECIAL TOOLS
Item(Namber&Name) Illustration Use
09452 - 21200
Oil seal installer
Oil seal installation
09200 - 38001
Engine supporting fixture
Removal and installation of transaxle
09455 - 32200
Oil seal puller
Removal of oil seal
09455 - 21000
Bearing&gear puller
Removal of taper roller vearing
09432 - 33200
plate
Removal of oil seal
09478 - 26100
Backing plate remover
Removal of 4WD coupling backing plate
09478 - 26000
Flange oil seal installer
Installation of 4WD coupling flange oil seal

2007 > 2.7L V6 GASOLINE >
SPECIFICATION
Engine type µ 2.7
Manual transaxle type M5GF2
Gear ratio 1st 3.615
2nd 1.931
3rd 1.969
4th 1.273
5th 0.974
Reverse 3.416
Final gear ratio 5.071
3.737
T/M oil capacity(ℓ) ※ 1.9 liter (2.0077US qt, 1.6718mp qt)
※ The quantity in the chart above is for the reference. The actual filling quantity of the automatic transaxle fluid must
be set according to 'INSPECTION' or 'REPLACEMENT' procedure of the automatic transaxle fluid.
Recommended transaxle oil SAE75W/85 or API GL - 4
Check&Replenishment Every one year or every 100,000km
Replacement Private useNormal use
No service required
Severe use( ※)
Every 100,000 Km
Business use
※ Severe use(marked '※') is defined as:
1. Driving on rough road(bumpy road, gravel road, snowy road, unpaved road etc.).
2. Driving on mountain road, ascent/descent.
3. Repetition of short distance driving.
4. More than 50% operation in heavy city traffic during hot weather above 32°C(89.6°F).
5. Police car, Taxi, Commercial type operation or trailer towing, etc.
TIGHTENING TORQUE
Item Nmkgf.m lb- ft
Oil drain plug 30~353.0~3.521.7~25.3
Oil filler plug 30~353.0~3.521.7~25.3
Back up lamp switch 30~353.0~3.521.7~25.3
Control shaft assembly 10~121.0~1.2 7.2~8.7
Select lever 43~554.3~5.531.1~39.8
Shift link assembly 43~554.3~5.531.1~39.8
Transaxle mounting bracket assembly 65~856.5~8.547.0~61.5
Transaxle and enging mounting bolt 65~856.5~8.547.0~61.5
SERVICE STANDARD Item Specification [mm(inch)]

2007 > 2.7L V6 GASOLINE >
SERVICE ADJUSTMENT PROCEDURE
Transmission oil inspection and replacement
1. After parking the vehicle on a plain, stop the engine.
2. After removing the oil filler plug and washer, inspect the manual transaxle fluid condition and quantity.
3. If the manual transaxle fluid is contaminated, drain it out by removing the oil drain plug.
4. Tighten the new oil drain plug and feed manual transaxle fluid to a proper level.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)
Oil type: SAE75W/85
Oil quantity:
1.9 liter(2.0077 US qt, 1.6718 lmp qt)
5. Retighten the oil filler plug with a new washer.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)
Back up lamp switch inspection
1.Disconnect the back up lamp switch connector(B).
2.Inspect the continuity of the switch. When the shift lever is located in reverse range, it should be applied an electric
current.
3. Replace the back up lamp switch, if necessary.
TORQUE:
29.4~34.4 Nm(3.0~3.5kgf.m, 21.7~25.3lb - ft)

11.Remove the transaxle insulator bracket (B) by removing the bolts (A).
12.Remove the front wheels and tires. (see SS group)
13. Lift up the vehicle.
14. Remove the steering column joint bolt. (see ST group).
15. Remove the under cover(A).
16.Drain power steering oil through the return tube(A). (see ST group)

17.Disconnect the power steering pressure hose (A) from the power steering oil pump. (see ST group)
18.Drain the tranaxle fluid through the drain plug.
19. Remove the hanger(A).
20.Disconnect the lower arm, the tie rod end ball joint, the stabilizer bar link from the front knuckle. (see SS group)
21. Remove the roll stopper mounting bolt(A).
22.Remove the power steering return tube mounting bolt(A)

12.Install the power steering return tube mounting bolt(A).
13.Install the front roll stopper mounting bolt(A).
14.Connect the lower arm, the rod end ball joint, the stabilizer bar link to the front knuckle.(see SS group)
15. Install the hanger(A).
16.Refill the transaxle with fluid.
17. Connect the power steering pressure hose (A) to the power steering oil pump.
18.Connect the power steering return hose(A). (see ST group)