2007 ISUZU KB P190 Harness

CAB 10-15
REASSEMBLY




This illustration is based on RHD model

RTW 4A0LF000801

Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Door lock cylinder / Door lock cylinder
with door lock switch (European
Countries)
▲ 4. Door lock cylinder protector (EUROPE)
▲ 5. Outside handle
▲ 6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (European Countries)
9. Glass run
10. W indow regulator / Power window regulator
▲ 11. W indow glass
12. Inside lever
13. W aterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch
▲ 23. Switch bezel / W indow regulator handle

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-19
REAR DOOR ASSEMBLY (CREW CAB)
REMOVAL AND INSTALLATION



Removal Steps
▲ 1. Door harness
▲ 2. Check arm screw
▲ 3. Lower hinge bolt
4. Upper hinge bolt
5. Door assembly

Installation Steps
5. Door assembly
4. Upper hinge bolt
▲ 3. Lower hinge bolt
▲ 2. Check arm screw
1. Door harness



RUW 5A0SH003301

Important Operations - Removal
1. Door Harness
Remove the center pillar lower trim cover and disconnect the door harness connector.


2. Check Arm Screw


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-21
DISASSEMBLY




10
11
15
14
16
7
13
3
4
5
1
2
9
6 8
12
1

RTW 7A0LF000901

Disassembly Steps
▲
1. Power window switch/W indow regulator
handle
▲ 2. Bezel
▲ 3. Door trim panel
▲ 4. Bracket
▲ 5. Speaker assembly
▲ 6. W aterproof sheet
▲ 7. Inside lever
▲ 8. Outer waste seal

▲
9. Glass run rear channel
▲ 10. W indow glass
▲ 11. W indow regulator/Power window
regulator
▲ 12. Glass run
▲ 13. Door lock assembly
▲ 14. Outside handle
15. Door harness assembly
16. Anti rattler


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-23

4. Bracket
5. Speaker assembly • Remove the fixing bolt and then remove the connector.
6. Waterproof Sheet • Take care not to damage the sheet when peeling it off.
7. Inside Lever • Disconnect the door lock cables.
8. Outer Waste Seal
9. Glass Run Rear Channel • Remove the bolt.

10. Window Glass
• Remove 2 bolts through the access hole and pull out the
window glass upward.

11. Window Regulator/Power Window Regulator
• Remove the 5 fixing bolts.
• Disconnect the power window motor connector.
12. Glass Run • Pull it out from the door frame of the channel.
13. Door Lock Assembly • Disconnect the lock cable from the anti rattler.
• Remove the 3 fixing screws and the bolt.
• Disconnect the linkage and harness connector.
14. Outside Handle • Remove the 2 fixing bolts.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

10-24 CAB
REASSEMBLY



7
6
2
3
1
10 4
14
13
11
12
16
15
8
9 5
16

RTW 7A0LF001001


Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Outside handle
4. Door lock assembly
5. Glass run
6. W indow regulator/Power window regulator
7. W indow glass
8. Glass run rear channel

9. Outer waste seal
10. Inside lever
11. W aterproof sheet
12. Speaker assembly
13. Bracket
14. Door trim panel
15. Bezel
▲ 16. Power window switch/W indow regulator
handle

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

10-28 CAB
▲ 7. Meter cluster assembly ▲ 14. Center cluster assembly
15. Audio bracket
▲ 16. Control lever assembly
17. Audio assembly
▲ 18. Ashtray bracket
19. Center cluster
20. Meter assembly
21. Passenger lower bracket
22. Glove box cover

▲ 23. Passenger air bag (if so equipped)
▲ 24. Side ventilation grille
▲ 25. Vent duct assembly/Defroster nozzle
assembly
26. Instrument harness assembly
▲ 27. Instrument panel assembly
28. Cross beam

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

10-30 CAB

RUW 5A0SH002701

12. Instrument Panel Assembly & Cross Beam
1) Remove the two bolts fixing the steering column to the cross beam and the two bolts fixing the brake pedal
bracket to the cross beam.

2) Remove the two bolts fixing the parking brake bracket to
the cross beam (Stick type parking brake only).


3) Disconnect the control cables at the blower unit and vent
unit.
4) Remove the fasteners fixing the instrument panel and cross beam assembly and the body panel.
5) Disconnect the instrument harness connectors.



This illustration is based on RHD model
RTW 7A0SF000201

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

10-32 CAB
INSTALLATION



18 19
19 19
18
24 231
3
2
20
21
278
22
25
26
17
9
6
5
5
7
28
14
10
11
15
13
16
12
4
This illustration is based on RHD model RTW 7A0LF001401

Installation Steps
1. Cross beam
2. Instrument panel assembly
3. Instrument harness assembly
4. Vent duct assembly/Defroster nozzle assembly
5. Side ventilation grille
6. Passenger air bag
7. Glove box cover
8. Passenger lower bracket
9. Meter assembly

10. Center cluster
11. Ashtray bracket
12. Audio assembly
13. Control lever assembly
14. Audio bracket
15. Center cluster assembly
16. Ashtray case
▲ 17. Instrument panel assembly & Cross
beam
18. Side cover

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007