2007 ISUZU KB P190 torque

REAR SUSPENSION 3D-9
Installation
1. Install the bump rubber and bolt and tighten it to thespecified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
42 (4.3/31)
2. Install the leaf spring. • The leaf spring assembly should be installed so that the
built-in rubber bush is toward the front.
• Align the holes of the spring eye and frame bracket.
• Insert the spring pin toward vehicle inner side, through
the frame bracket holes and the spring bush hole.
• Tighten the nut a little and, after the vehicle is lowered,
tighten it to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
152 (15.5/112)





RTW 340LF000101





RTW 63DSH000101
• Apply rubber grease to inside and outside of the rubber
bushing.
• Install the rubber bushings into the hole in the frame
side bracket and the spring rear eye.
• Install the shackle pin and shackle plate.
• Tighten the nuts a little and, after vehicle is lowered,
tighten it to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
98 (10.0/72)
3. Support the lower clamp under the leaf spring.
4. Apply oil to the thread portion of U bolt.
Install the U bolt (1) and seat (2) on the rear axle and insert
the U bolt in the lower clamp holes.
Tolerance of assembling the seat
A
90° ±2°
5. Tighten the nut to the specified torque.
NOTE: Apply oil to the thread.
Torque N⋅m (kgf ⋅m/lb ⋅ft)
78 (8.0/58)
6. Install the shock absorber and inner washer on the lower clamp pin and frame side pin.
7. Install the washer and nut on the frame side pin and tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
39 (4.0/29)
8. Install the washer and nut on the lower clamp pin and tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
39 (4.0/29)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3D-10 REAR SUSPENSION
9. Install the parking brake cable on the leaf spring and
tighten the nut at its bracket.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
7 (0.7/61)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3D-12 REAR SUSPENSION
Reassembly
1. Apply grease to both faces of each leaf spring at
reassembly.
2. Set the leaf springs, aligning them to the setting mark made
before disassembly.

F03L100006
3. Assemble the leaf springs using a bench press.
4. Apply grease to the outside of the bushing.
Install a new center bolt and tighten it to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
29 (3.0/22)
5. Install the bushing using a bench press and a suitable metal fitting.



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3D-14 REAR SUSPENSION

Removal
1. Remove the bolt and nut.
2. Take out the stabilizer bar assembly.
3. Remove the nut and take out the link from the stabilizer
bar.
4. Take out the cap and bush from the stabilizer bar.




Installation
1. Set the bush and cap on the stabilizer bar.
2. Install the link on the stabilizer bar and tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
50 (5.1/37)

3. Install the stabilizer bar assembly on the rear axle and
tighten the bolt to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
25 (2.5/18)

4. Set the stabilizer bar assembly to the frame bracket and
tighten the nut to the specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅ft)
50 (5.1/37)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-1
SECTION 3E
WHEELS AND TIRES
TABLE OF CONTENTS
PAGE
Main Data and Specifications ........................................................................................... 3E- 2
Torque Specifications ....................................................................................................... 3E- 3
Special Parts Fixing Nuts and Bolts ........................................................................... 3E- 3
Wheels and Tires ............................................................................................................... 3E- 4
General Description...................................................................................................... 3E- 4
Servicing...................................................................................................................... .. 3E- 6
Disassembly and Reassembly..................................................................................... 3E- 7
Inspection and Repair .................................................................................................. 3E- 8
Troubleshooting ................................................................................................................ 3E- 10


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-3
TORQUE SPECIFICATIONS
SPECIAL PARTS FIXING NUTS AND BOLTS
WHEELS AND TIRES
N⋅m (kgf ⋅m/lb ⋅ft)






RTW 73ELF000101



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

3E-6 WHEELS AND TIRES
SERVICING
Servicing refers to general maintenance procedures to be performed by qualified service personnel.




WHEEL NUT TORQUES
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)





TIRE ROTATION
For of radial tires, interchange the front and the rear wheels on
the same side as shown in the figure.





If one-sided tire wear appears on radial tires, rotate the wheels
as shown in the figure.

Note:
After rotation, adjust the front and rear tire pressure and be sure to check wheel nut tightness.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

WHEELS AND TIRES 3E-9
Important Operations
1. Tire Assembly
To assemble, align the match mark (approx. 10mm diameter
paint mark) on the wheel with the match mark (approx. 8mm
diameter red paint mark) on the tire. If the match mark on the
wheel has disappeared, align with air valve instead.

2. Wheel and Tire Assembly





3. Wheel Nut
Tighten wheel nuts in numerical order.
W heel Nut Torque N⋅m (kgf ⋅m/lb ⋅ft)
117.7 ± 9.8 (12 ± 1.0 / 86.8 ± 7.2)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007