2007 ISUZU KB P190 sensor

5B-12 ANTI-LOCK BRAKE SYSTEM
3. Check speed sensor cable for short or open, and
replace with a new one if necessary. To check fo
r
cable short or open, bend or stretch the cable while
checking for continuity.
Installation
1. Install the speed sensor.
2. Tighten the sensor fixing bolts to the specified torque.
Torque: 8 N ⋅m (0.8 kgf ⋅m / 69 lb·in)
3. Connect the cable fixing clips (arrow marked).
4. Install the cable fixing bolts and tighten it to the specified torque.
Torque: 8 N ⋅m (0.8 kgf ⋅m / 69 lb·in)
5. Connect the harness connector.


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ANTI-LOCK BRAKE SYSTEM 5B-13
Front Sensor Rotor
Front Sensor Rotor and Associated Parts
411R300010
Legend
(1) Sensor Rotor
(2) Hub and Disc


(3) Disc Rotor fixing Bolt
(4) Hub and Disc Assembly
Removal
1. Remove the hub and disc assembly. (Refer to the
section Front wheel Drive).
2. Remove two disc rotor fixing bolts on a diagonal.
3. Drive out the sensor rotor using a metal bar and hammer through the two bolt holes.
• Discard the used sensor rotor.
4. Install disc rotor fixing bolts and tighten them to the specified torque.
Torque: 103 N ⋅m (10.5 kgf ⋅m / 76 lb·ft)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5B-14 ANTI-LOCK BRAKE SYSTEM
411R300007
Legend
(1) Metal Bar


(2) Sensor Rotor
Inspection and Repair
Make all necessary adjustments, repairs or part
replacement.
• Check damage or powdered iron sticking to the
sensor rotor.
• Check play in the sensor rotor.
• Check a broken tooth or indentation in the senso
r
rotor.
Installation
1. Set a new sensor rotor.
2. Install the new sensor rotor in the hub, using installer 5-8840-2789-0 and grip 5-8840-0007-0.
NOTE: Sensor rotor is surely using a new article.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ANTI-LOCK BRAKE SYSTEM 5B-15
411R300006
Legend
(1) Hub and Disc
(2) Sensor Rotor


(3) Press
3. Measure the gap “A” at 4 points at intervals of 90 °
(degrees).
Confirm that the gap “A” should be within the
specified range.
Range

Type A
4 × 2 (Except High Ride
Suspension) 7.0
− 7.4 mm
(0.276 − 0.291 in)
4 × 4
4 × 2 High Ride Suspension 7.2
− 7.6 mm
(0.283 − 0.299 in)

411R300016
4. Install the hub and disc assembly. (Refer to the
section Front wheel Drive).


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5B-16 ANTI-LOCK BRAKE SYSTEM
Rear Sensor Rotor
Rear Sensor Rotor and Associated Parts




RTW 55BLF000101

Legend
(1) Axle Shaft Assembly with Brake
(2) Sensor Rotor


(3) Front
Removal
1. Remove the axle shaft assembly with brake. (Refer
to the section Rear Axle)


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ANTI-LOCK BRAKE SYSTEM 5B-17



RUW 55BMF000101

Legend
(1) Bench Press Fitting
(2) Axle Shaft


(3) Sensor Rotor
Inspection and Repair
Make all necessary adjustments, repairs or part
replacement.
• Check damage or powdered iron sticking to the
sensor rotor.
• Check play in the sensor rotor.
• Check a broken tooth or indentation in the senso
r
rotor.
NOTE: If replacement is required, remove the
sensor rotor from the axle shaft assembly with
brake. (Refer to the section Rear Axle).
• Discard the used sensor rotor.
(Snap ring, Oil seal and Bearing)
Installation
1. Install the sensor rotor and assemble it into the
axle shaft assembly with back plate, using setting
tool 9-8522-1271-0. (Refer to the section Rea
r
Axle)

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

5B-18 ANTI-LOCK BRAKE SYSTEM

420R300005
Legend
(1) Axle Shaft
(2) Oil Seal
(3) Bolt


(4) Back Plate
(5) Sensor Rotor
(6) Double Taper Roller Bearing
2. Install the axle shaft assembly with brake in the rear axle. (Refer to the section Rear Axle).

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

ANTI-LOCK BRAKE SYSTEM 5B-19
G-Sensor
G-Sensor and Associated Parts


This illustration is based on the RHD model
RTW 75BLF000101
Legend
(1) G-Sensor


(2) Nut
Removal
1. Remove the front floor console. (Refer to the section Floor Console)
2. Disconnect the connector.
3. Remove the nuts.
4. Take out the G-sensor.

Installation
1. Set the G-sensor.
2. Install the nut and tighten it to specified torque.
Torque: 8 N·m (0.8 kgf·m / 69 lb·in)
3. Connect the connector.
4. Install the front floor console. (Refer to the section Floor Console)



BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007