2007 Hyundai Matrix Owner's Manual

1CONTROLS AND EQUIPMENT
10
B070F02A-EAT Keyless Entry System (Not all models) Locking doors
1. Close all doors.
2. Push the "LOCK" button on the trans-mitter.
3. At the same time all doors lock, the
turn signal light will blink once toindicate that the system is armed.
Unlocking doors
1. Push the "UNLOCK" button on the transmitter.
2. At the same time all doors unlock,
the turn signal light will blink twice to indicate that the system is disarmed.
NOTE: The transmitter will not work if any of following occur:
- The ignition key is in ignition switch.
- You exceed the operating distance limit (10 m).
- The battery in the transmitter is
weak. B070E02HP-GAT Replacing the battery When the transmitter's battery becomes weak, it may take several pushes on the button to lock or unlock the doors,and the LED will not light. Replace the battery as soon as possible. Battery type : CR2032 Replacement instructions:
1. Separate the case with a blade screw-
driver as shown in the illustration.
MSO-0048-1
Screwdriver
- Other vehicles or objects may be
blocking the signal.
- The weather is extremely cold.
- The transmitter is close to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the trans- mitter.
When the transmitter does not workcorrectly, open and close the doorwith the ignition key. If you have a problem with the transmitter, con- tact an authorized Hyundai Dealer. NOTE: Keep the transmitter away from wa- ter or any liquid. If the keyless entry system is inoperative due to expo-sure to water or liquids, it will not be covered by your manufacturer ve- hicle warranty.
fcuk-1.p65 12/27/2006, 10:11 AM
10

1
CONTROLS AND EQUIPMENT
11
!
2. Before removing the battery note its
position and ensure the new battery is fitted the same + side (positive) facing down, then insert it into trans- mitter.
MSO-0048-2
Battery
Case
WINDOW
SB060A1-E MANUAL WINDOWS The front door windows may be opened or closed by turning the window regula- tor handle. Ensure that when the win- dows are closed, nothing may becometrapped between the glass and the door frame.
WARNING:
When opening or closing the win- dows, make sure your passenger's arms and hands are safely out of the way. B060A03E-EAT POWER WINDOWS (Not all models) The power windows operate when the ignition key is in the "ON" position. The
main switches are located on the driver's armrest and control the front and rearwindows on both sides of the vehicle. The windows may be opened by de- pressing the appropriate window switchand closed by pulling up the switch. To open the window on the driver's side, press the switch(1) down. The windowmoves as long as the switch is oper- ated.
B050A01FC-D
Close
B060A01FC-D
(1)
Open
fcuk-1.p65
12/27/2006, 10:11 AM
11

1CONTROLS AND EQUIPMENT
12
!
!
SEAT
B080A01FC-EAT SEAT ADJUSTMENT
WARNING:
Front seat adjustments must not be undertaken whilst the vehicle is inmotion. Loss of control of the ve- hicle may result if seat adjustments are made whilst the vehicle is inmotion.
In order to prevent operation of the passenger front and rear windows, a window lock switch is provided on thearmrest of the driver's door. To disable the power windows, press the window lock switch.To return to normal operation, press the window lock switch a second time. Auto-Down Window (Driver's Side) The Auto-Down window is moved to its fwitch. To stop at the desired loction, the switch must be pulled up. WARNING:
1) Be careful that someone's head, hands or body are not trapped by a closing window.
2) Never try to operate the main
switch on the driver's door and theindividual door window switch in opposing directions at the sametime. If this is done, the window will stop and cannot be opened or closed.
3) Always remove the ignition key prior to exiting the car.
4) Do not leave children alone in the car.
HFC2013-D
fcuk-1.p65 12/27/2006, 10:11 AM
12

1
CONTROLS AND EQUIPMENT
13
!
B080B02FC-EAT FRONT SEATS Front Seat Rake Adjustment The front seat rake adjustment is per- formed by raising the lever at the front of the seat base and sliding the seat to the desired position. At this position thelever should be released and the seat rocked to and fro to ensure that the mechanism has locked.
WARNING:
To ensure the seat is locked se-curely, attempt to move the seat for-ward or rearward without using the lock release lever. SB070C1-E Front Seat Recline Adjustment The front seat back recline angle may be adjusted by leaning forward slightly and raising the recline adjustment lever at the side of the seat. When theseatback is at the desired angle, the lever should be released. Ensure that the seatback is locked before drivingthe vehicle.
SB070D3-E Head Restraint Adjustment To raise the head restraint, pull it up. To lower it, push it down whilst pressing the lock knob. For maximum effective- ness in the event of an accident, therestraint must be adjusted so that the restraint is approximately at the level of the seat occupant's eyes. The restraintmust never be so adjusted that it is centred about the level of the seat occupant's neck.
HFC2024-D
HFC2025-D
Lock Knob
HFC2028
fcuk-1.p65 12/27/2006, 10:11 AM
13

1CONTROLS AND EQUIPMENT
14
!WARNING:
SB070E1-E Lumbar Support Adjustment (Driver's seat only)(Not all models) Some models are fitted with adjustable driver seat lumbar support which may be used to increase the amount oflumbar support offered by the seat back. Adjustment is performed by moving the handle at the side of the backrest in a
forward direction to increase the support.
1. Maximum Support
2. Minimum Support SB070F1-E Seat Cushion Height Adjustment (Driver's seat only)(Not all models) To raise or lower the front part of the seat cushion, turn the front knob clock- wise or counter-clockwise. To raise or lower the rear part of the seatcushion, turn the rear knob clockwise or counter-clockwise.
B080D01JM
o For maximum effectiveness in case of an accident the head restraint should be adjusted so the middle of the head restraint is at the same height as the top of the occupant's eyes. For this reason, the use of a cushion that holds the body away from the seatback should not be recommended.
o Do not operate vehicle with the head restraints removed as injury to the occupants may occur in the event of an accident. Head re- straints may provide protection against neck injuries when prop- erly adjusted. o Do not adjust the head restraint
height whilst the vehicle is in motion.
1
2
HFC2027-D
HFC2026-D
fcuk-1.p65 12/27/2006, 10:11 AM
14

1
CONTROLS AND EQUIPMENT
15
!
B080G01FC-EAT UNDER TRAY (Not all models) The tray is located under the front passenger seat. It is opened by up and pulling forward.
HFC2060
WARNING:
To avoid the possibility of injury in case of an accident or a sudden stop,the tray should be kept closed when the car is in motion. B080H01FC-GAT REAR SEAT Seat Rake Adjustment The front seat rake adjustment is per- formed by raising the lever at the front of the seat base and sliding the seat to the desired position. At this position thelever should be released and the seat rocked to and fro to ensure that the mechanism has locked.
B080I01FC-BAT Adjusting Seatback Angle
HFC2061
Seatbackfolding leverTo recline the seatback, push the seatback folding lever toward the head- rest, and release it after the desired seatback angle is achieved.When you recline the seatback to de- sired position, always be sure it has locked into position.
!
CAUTION:
When reclining the seatback, you should adjust the seatback foldinglever whilst standing.
HFC2059
fcuk-1.p65 12/27/2006, 10:11 AM
15

1CONTROLS AND EQUIPMENT
16
!
SB070D3-E Head Restraint Adjustment To raise the head restraint, pull it up. To lower it, push it down whilst pressing the lock knob. For maximum effective- ness in the event of an accident, therestraint must be adjusted so that the restraint is approximately at the level of the seat occupant's eyes. The restraintmust never be so adjusted that it is centred about the level of the seat occupant's neck. WARNING:
Lock Knob
B090B01FC-GAT Folding Rear Seatback and Seat Cushion For greater convenience, the entire seatback anad seat cushion may be folded down and up.
B090A01FC
HFC2074
B080D01JM
o For maximum effectiveness in case of an accident the head restraint should be adjusted so the middle of the head restraint is at the same height as the top of the occupant's eyes. For this reason, the use of a cushion that holds the body away from the seatback should not be recommended.
o Do not operate vehicle with the head restraints removed as injury to the occupants may occur in the event of an accident. Head re- straints may provide protection against neck injuries when prop- erly adjusted. o Do not adjust the head restraint
height whilst the vehicle is in motion.
1. Move the rear seat to the rearmost position.
2. Remove the head restraints.
fcuk-1.p65 12/27/2006, 10:11 AM
16

1
CONTROLS AND EQUIPMENT
17
3. To fold down the seatback , push and
hold the seatback folding lever to- ward the head restraints, then push down the seatback.
4. Pull the seat cushion release lever upward, then fold up the seat cushion.
! 5. To secure the seat, hook the secur-
ing strap under the seat cushion to the headrest stay of front driver and passenger seat.
6. Insert the removed headrests be-
tween the seatback and seat cush-ion, so that they will not be thrown forward in the case of a sudden stop or an accident.
7. To return the seatback and seat cushion to its normal position, re-verse the above procedure.
o When you return the seatback to its upright position, always be sure it islocked into position by pulling andpushing on the top of seatback. WARNING:
o When you return the folded down seat back to its upright position, make sure the seat belts are in position to be accessible and tofunction properly.
o The purpose of the fold down rear
seat back and the fold forward rearseat cushion is to increase cargo space. Do not allow passengers to sit in the cargo area whilst the caris moving. This is not a proper seating position and no seat belts are available for use when the seat back is folded down. Passengers who are not properly seated andwearing seat belts could sustain serious injuries or death in case of an accident or a sudden stop.
o Objects should not extend higher than the top of the front seatbacks.This could allow cargo to slideforward and cause injury or dam- age during sudden stops.
!
CAUTION:
To prevent damage, ensure that the rear drinkholder, located in the rear console, is closed before folding the rear seatback and seat cushion. Seat cushion release lever
HFC2075
HFC2076
Securing strap
fcuk-1.p65
12/27/2006, 10:11 AM
17