2007 GMC YUKON XL Owners Manual

✍NOTES
185

Instrument Panel Overview
United States version shown; Canada similar
186

A. Air Outlets. SeeOutlet Adjustment on
page 220.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 190.
C. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 225.
D. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 188.
E. Shift Lever. SeeAutomatic Transmission
Operation on page 142.
F. Tow/Haul Selector Button (If Equipped).
SeeTow/Haul Mode on page 145.
G. Driver Information Center Controls. SeeDriver
Information Center (DIC) on page 244.
H. Audio System. SeeAudio System(s) on
page 274.
I. Exterior Lamps Control. SeeExterior Lamps on
page 199.
J. Dome Lamp Override Button. SeeDome Lamp
Override on page 204.
K. Automatic Transfer Case Control. (If Equipped).
SeeFour-Wheel Drive on page 146.
L. Cruise Control Buttons. SeeCruise Control on
page 196.M. Tilt Wheel Lever. SeeTilt Wheel on page 189.
N. Horn. SeeHorn on page 189.
O. Audio Steering Wheel Controls. SeeAudio
Steering Wheel Controls on page 334.
P. Climate Controls. SeeClimate Control System
on page 210or Dual Automatic Climate
Controls (If Equipped). SeeDual Automatic
Climate Control System on page 213.
Q. Accessory Power Outlets. SeeAccessory
Power Outlet(s) on page 208. Cigarette Lighter
(If Equipped). SeeAshtray(s) and Cigarette
Lighter on page 209.
R. StabiliTrak
®Button (If Equipped). See
StabiliTrak®System on page 348. Pedal Adjust
Button (If Equipped). SeeAdjustable Throttle
and Brake Pedal on page 140. Rear Park Assist
Disable Button (If Equipped). SeeUltrasonic
Rear Parking Assist (URPA) on page 205.
Heated Windshield Washer Fluid Button
(If Equipped). SeeWindshield Washer on
page 194. Power Running Boards Disable
Button (If Equipped). SeePower Running
Boards on page 129.
S. Glove Box. SeeGlove Box on page 174.
187

Hazard Warning Flashers
The hazard warning ashers warn others.
They also let police know you have a problem.
Your front and rear turn signal lamps will ash
on and off.
The hazard warning
asher button is located
on top of the steering
column.The hazard warning ashers work no matter what
ignition position the key is in, and even if the
key is not in the ignition.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
When the hazard warning ashers are on, your
turn signals will not work.
Other Warning Devices
If you carry reective triangles, you can set them up
at the side of the road about 300 feet (100 m)
behind your vehicle.
188

Horn
To sound the horn, press the center pad on the
steering wheel.
Tilt Wheel
Your vehicle has a tilt wheel, that lets you adjust
the steering wheel before driving. Raising it to
the highest level gives more room to exit and enter
your vehicle.
The tilt steering wheel lever is located on the
lower left side of the column.
To tilt the wheel, hold the steering wheel and pull
the lever. Then move the steering wheel to a
comfortable position and release the lever to lock
the wheel in place.
189

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
G(Turn and Lane Change Signals):See
Turn and Lane-Change Signals on page 191.
53(Headlamp High/Low-Beam
Changer):SeeHeadlamp High/Low-Beam
Changer on page 192.
Flash-to-Pass. SeeFlash-to-Pass on page 192.
N(Windshield Wipers):SeeWindshield
Wipers on page 192.
L(Windshield Washer):SeeWindshield
Washer on page 194.
5(Rear Wiper Delay):SeeRear Window
Wiper/Washer on page 195.
Z(Rear Wiper):SeeRear Window
Wiper/Washer on page 195.
=(Rear Wiper Wash):SeeRear Window
Wiper/Washer on page 195.
190

Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever will
return automatically.
To signal a lane change, raise or lower the lever
for less than one second until the arrow starts
to ash. This will cause the turn signals to
automatically ash three times. It will ash
six times if tow-haul mode is active. Holding the
turn signal lever for more than one second
will cause the turn signals to ash until you release
the lever. The lever will return by itself when it is
released.
An arrow on the
instrument panel cluster
will ash in the
direction of the turn or
lane change.As you signal a turn or a lane change, if the
arrows ash more quickly than normal, a signal
bulb may be burned out and other drivers will not
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when
you signal a turn, check for burned-out bulbs and a
blown fuse. SeeFuses and Circuit Breakers on
page 540.
Turn Signal On Chime
If your turn signal is left on for more than
3/4 of a mile (1.2 km), a chime will sound at
each ash of the turn signal and the message
TURN SIGNAL ON will also appear in the DIC.
To turn the chime and message off, move the turn
signal lever to the off position.
191

Headlamp High/Low-Beam Changer
53(Headlamp High/Low Beam Changer):
To change the headlamps from low to high beam,
push the lever toward the instrument panel. To
return to low-beam headlamps, pull the
multifunction lever toward you. Then release it.
When the high beams
are on, this indicator light
on the instrument panel
cluster will also be on.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass. It works even if your headlamps
are in the automatic position.
To use it, pull the turn signal lever toward you,
then release it.
If your headlamps are in the automatic position or
on low beam, your high-beam headlamps will turn
on. They will stay on as long as you hold the levertoward you. The high-beam indicator on the
instrument panel cluster will come on. Release the
lever to return to normal operation.
Windshield Wipers
Be sure to clear ice and snow from the wiper blades
before using them. If they are frozen to the
windshield, gently loosen or thaw them. Damaged
wiper blades may not clear the windshield well,
making it harder to see and drive safely. If the
blades do become damaged, install new blades or
blade inserts. For more information, seeWindshield
Wiper Blade Replacement on page 481
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it
cools down. Clear away snow or ice to prevent an
overload.
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):For a single wiping cycle, turn the
band to mist. Hold it there until the wipers start.
Then let go. The wipers will stop after one wipe.
If you want more wipe cycles, hold the band
on mist longer.
192