2007 GMC SAVANA Owner's Manual

{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire. To
help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will
not move, you should put blocks at the
front and rear of the tire farthest away
from the one being changed. That would
be the tire, on the other side, at the
opposite end of the vehicle.When your vehicle has a flat tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.
361

Removing the Spare Tire and Tools
If you have a cargo van or a passenger van,
the equipment you will need is located in
the passenger side rear corner of the vehicle.
Remove the retaining
wing bolt and lift it off of
the mounting bracket.
If you have a van with the 15-passenger seating
arrangement, the equipment you will need is
secured on the rear floor of the passenger side
of the vehicle.To access the equipment, remove the retaining
wing bolt and lift it out of the mounting bracket.
362

The tools you will be using include the jack (A),
jack handle extension (B), jack handle (C),
wheel wrench (D), and the ratchet (E).
The spare tire is stored underneath the rear of
your vehicle. You will use the wheel wrench (D)
and the ratchet (E) to lower the spare tire from
the vehicle.To lower the spare tire from the vehicle, do the
following:
1. Attach the wheel
wrench and ratchet,
with the DOWN side
facing you. The
wheel wrench has a
socket end and a flat
chisel end. Note that
there is an UP side
and a DOWN side on
the ratchet.
2. Put the flat chisel end of the wheel wrench on
an angle through the hole between the body
and the bumper. Be sure the flat end
connects into the hoist shaft.
363

3. Turn the ratchet counterclockwise to lower the
spare tire to the ground. If the spare tire does
not lower to the ground, the secondary
latch is engaged causing the tire not to lower.
SeeSecondary Latch System on page 371.4. When the tire has been lowered, pull the tire
toward you so you can reach the tire retainer
and pull it up through the wheel opening.
If you have a vehicle which was completed from a
cab and chassis, refer to the information from
the body supplier/installer.
The spare tire is a full-size tire, like the other tires
on your vehicle.
364

Removing the Flat Tire and
Installing the Spare Tire
If your vehicle has plastic wheel nut caps,
loosen them by turning the wheel wrench
counterclockwise. The wheel nut caps are
designed to remain with the center cap. Remove
the center cap.
If the wheel has a smooth center piece, place the
chisel end of the wheel wrench in the slot on
the wheel and gently pry it out.
1. With the DOWN side facing you, use the
ratchet and wheel wrench to loosen all the
wheel nuts. Do not remove them yet.2. Assemble the jack and tools for a front or rear
flat as follows:
Front Flat:Assemble the jack (A) together
with the jack handle (B) and ratchet (C)
as shown. Be sure that the ratchet has the
UP mark facing you.
Front Position
365

Rear Flat:Assemble the jack (A) together with
the jack handle (B), jack handle extension (C)
and ratchet (D) as shown. Be sure that the
ratchet has the UP mark facing you. To
assemble the jack handle and jack handle
extension, use the art and text following.Connect the jack handle (B) and jack handle
extension (C) together and press the retention
clip (arrow) so it engages.
Rear Position
366

3. Position the jack
under the vehicle
as shown.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
Front Position
Rear Position
367

{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall. To
help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising
the vehicle.
4. Raise the vehicle by turning the ratchet
clockwise. Make sure the UP mark faces you.
Raise the vehicle far enough off the ground
so there is enough room for the spare
tire to fit.
368