2007 FORD FIESTA Air con

303-00-25 Engine System - General Information 303-00-25
DIAGNOSIS AND TESTING
11. Install the fuel pump relay.
-. 12 Install the air cleaner.
REFER to: Air Cleaner
- 2.OL Duratec-HE (M14)
(303-12 Intake Air Distribution and Filtering,
Removal and Installation).
13 Reset the PCM fault memory.
Measure the oil ressure (Engine - 1.4L
Duratorq-TDCi PDv) Diesel)
N0TE:The oil pressure depends on various factors
(engine speed, oil temperature, oil viscosity, extent
4m Attach the oil pressure gauge with the oil of oil filter contamination).
pressure gauge connector, and position it to
N0TE:Measure the oil pressure at the specified allow reading
from above.
engine speed.
5. Lower the vehicle.
I. Raise and support the vehicle. REFER to:
(1 00-02 Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
6. N0TE:Measure the oil pressure at an oil
temperature of 410°C.
N0TE:OiI pressure at 2000 rpm: 2.3 to 3.7 bar.
Measure the oil pressure.
2. Disconnect the oil pressure switch electrical
7. Raise and support the vehicle. Engine
- 1.4L connector from the oil pressure switch.
Duratorq-TDCi (DV) Diesel
3. Remove the oil pressure switch.
Discard the washer.
8. Remove the oil pressure gauge and the oil
pressure gauge connector.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-01 A-I Engine
. 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-I
6V (Sigma)ll . 6L Duratec-1 6V (Sigma)
303-01 A-I
SECTION 303-01A Engine . 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-I 6V (Sigma)/l . 6L Duratec-1 6V
(Sigma)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
.............................................. Specifications
Engine Data
. 1.25L ........................................................................\
................................
Engine Data . I . 4L ........................................................................\
..................................
Engine Data . 1.6L ........................................................................\
..................................
Oil pressure ........................................................................\
.............................................
Engine Oil Capacity . - 1.25Ll1.4L ........................................................................\
............
Engine Oil Capacity - 1.6L ........................................................................\
......................
Valve Clearance - 1.25LlI . 4L ........................................................................\
..................
Valve Clearance - 1.6L ........................................................................\
............................
Cylinder block - 1.25L ........................................................................\
.............................
Cylinder block - 1.4L ........................................................................\
...............................
........................................................................\
............................... Cylinder block - 1.6L
........................................................................\
.......................................... Cylinder head
Piston
-1.25L ........................................................................\
...........................................
Piston -1.4L ........................................................................\
.............................................
Piston - l.6L ........................................................................\
............................................
PAGE
DESCRIPTION AND OPERATION
........................................................................\
......................................................... Engine 303-01A-9
........................................................................\
.................... 1.4Ll1.6L Duratec 16V engine 303-01A-9
DIAGNOSIS AND TESTING
........................................................................\
......................................................... Engine 303-01A-12
GENERAL PROCEDURES
........................................................................\
....................... Valve Clearance Adjustment 303-01 A-I 3
IN-VEHICLE REPAIR
Crankshaft Front Seal ........................................................................\
......... (21 467 0)
Valves ........................................................................\
..................................... (21 21 5 4)
Intake Manifold ........................................................................\
....................... (21 183 0)
Valve Cover ........................................................................\
............................ (21 141 0)
Valve Seals ........................................................................\
............................. (21 238 0)
Camshafts ........................................................................\
........................ (21 284 0)
Camshaft Seal ........................................................................\
................... (21 288 0)
Timing Belt ........................................................................\
.......................... (21 304 0)
Exhaust Manifold ........................................................................\
.................... (21 187 0)
Cylinder Head ........................................................................\
...................... (21 163 0)
Oil Pan ........................................................................\
............................. (21 154 0)
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)Il.GL Duratec-1 6V (Sigma)
SPECIFICATIONS
2006.0 Fiesta 1212006 GI 54208en
Ib-in
-
-
-
-
-
-
-
-
-
80
-
80
-
35
-
80
-
-
-
-
-
-
80
80
-
-
-
53
-
80
80
Ib-ft
41
35
66
35 35 18
30
18
35
-
20
-
15
-
21
-
11
-
-
13
-
35
-
-
11
15
15
-
-
-
-
Description
Engine front mount bracket to cylinder block
retaining bolts
Engine front mount retaining nuts and bolts
Engine rear mount center retaining nut
Engine rear mount outer retaining nuts
Engine support insulator retaining bolts Power steering line support bracket retaining bolts
Power steering line to power steering pump
Air conditioning
(AIC) compressor to cylinder block
retaining bolts
Generator to cylinder block top rear and lower
retaining bolts
Water pump retaining bolts
Water pump pulley retaining bolts
Oil pump to cylinder block retaining bolts
Oil pan to cylinder block retaining bolts
Oil level indicator tube bracket retaining bolt
Engine oil drain plug
Oil pump pickup pipe to cylinder block retaining
bolts
Oil pressure switch
Cylinder head bolts
Valve cover retaining bolts
Intake manifold to cylinder head retaining bolts
Exhaust manifold to cylinder head
Exhaust manifold to cylinder block
Camshaft position (CMP) sensor
Timing belt rear cover retaining bolts
Spark plugs Engine rear lifting eye retaining bolts
Coolant distribution housing retaining bolts
Ignition coil to coolant distribution housing
Camshaft bearing cap retaining bolts
Timing belt upper cover to cylinder block retaining
bolts
Timing belt lower cover to cylinder block retaining
bolts
Nm
55
48 90
48
48 25
40 25
47
9
27 9
20 4
28 9
15
a)
a)
18
a)
47 9
9
15
20
20
6
a)
9
9
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01 A-9 Duratec-1 6V (Sigma)/l .6L
Duratec-1 6V (Sigma) 303-01 A-9
DESCRIPTION AND OPERATION
Engine
i
1.4U1.6L Duratec 16V engine
Overview
The 1.4L and 1.6L Duratec 16V inline engines have The intake air routing and the air cleaner housing
already been installed on Focus vehicles under the have
also been changed. The pistons and piston
name of the Zetec-SE engine. rings
have been modified. The cylinder head cover
Details of this engine have been modified. The is
made of plastic.
routing of the pipes in the intake manifold has been
In addition, the auxiliary drive belt is an elastic
revised, and for the first time the throttle valve is multi-groove belt without a separate tensioning
electronically controlled. roller.
2006.0 Fiesta 1212006 GI 7901 7en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01A-I 9 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-OIA-I 9
IN-VEHICLE REPAIR
Intake Manifold(21 183 0)
Removal 6. Remove the intake manifold lower retaining
bolt.
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable mixtures
are always present and may ignite. Failure
to follow these instructions may result in
personal injury.
1. Release the fuel system pressure. For
additional information, refer to
Section
31 0-00 [Fuel System - General
Information].
2. Disconnect the battery ground cable. For
additional information, refer to
Section
414-01 [Battery, Mounting and 7. Disconnect the engine wiring harness
Cables]. electrical connector.
3. Remove the air cleaner. For additional
information, refer to Section
303-1 2 [Intake
Air Distribution and Filtering].
4. Detach the power steering fluid reservoir
from the bracket and position
it to one side.
5. Remove the accessory drive belt. For
additional information, refer to
Section
303-05 [Accessory Drive].
8. Disconnect the positive crankcase ventilation
(PCV) hose from the PCV.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llm4L
303-01 A120 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 Am20
IN-VEHICLE REPAIR
9. Disconnect the brake booster vacuum line
from the intake manifold. 12. Detach the oil level indicator tube from the
intake manifold.
/'-
10. Disconnect the evaporate emission (EVAP) 13. Disconnect the temperature and manifold
hose from the EVAP valve. absolute pressure (T-MAP) sensor electrical
connector.
11. Disconnect the knock sensor (KS) electrical
connector.
14. Disconnect the throttle plate control motor
(DC-ISC) electrical connector.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll14L
Duratec-1 6V (Sigma)ll16L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
15. Disconnect the generator electrical 17. Disconnect the fuel injector electrical
connector. connectors and
position it with the engine
i wiring harness to one side.
16. Detach the generator from the engine.
1. Remove the bolts.
2. Remove the nut and the stud.
18. Disconnect the engine coolant temperature
(ECT) sensor electrical connector.
2006.0 Fiesta 1~12006 GI 83728en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
IN-VEHICLE REPAIR
19. Disconnect the fuel supply line quick Discard the O-ring seals.
release coupling. For additional
information, refer to Section
31 0-00 [Fuel
System
- General Information].
20. Disconnect the fuel return line quick release
coupling. For additional information, refer
to Section
31 0-00 [Fuel System - General
Information].
21. Detach the fuel line from the intake
manifold and position
it to one side.
Remove the cable tie.
22.
Remove the fuel supply manifold.
23. Detach the wiring harness and the coolant
hose from the intake manifold.
24. Detach the wiring harness from the intake
manifold.
25. Remove the intake manifold.
2006.0 Fiesta 1212006 GI 83728en
procarmanuals.com