2007 CHEVROLET IMPALA lock

7. Turn the bulb socket counterclockwise to
remove it.
8. Install a new bulb.
9. Turn the bulb socket clockwise to reinstall it.
10. Reverse Steps 1 through 6 to reinstall the
taillamp assembly.
When reinstalling the taillamp assembly, make
sure that you line up the four posts on the
assembly with the slots in the vehicle.License Plate Lamp
To replace one of these bulbs:
1. Turn the lamp assembly counterclockwise and
pull the lamp assembly out of the connector.
2. Pull the old bulb from the lamp assembly,
keeping the bulb straight as you pull it out.
3. Install the new bulb.
4. Reverse Steps 1 through 3 to reinstall the
license plate lamp.
348

Vehicles that have a tire pressure monitoring
system may give an inaccurate low-pressure
warning if non-TPC Spec rated tires are installed
on your vehicle. Non-TPC Spec rated tires
may give a low-pressure warning that is higher or
lower than the proper warning level you would
get with TPC Spec rated tires. SeeTire Pressure
Monitor System on page 360.
Your vehicle’s original equipment tires are listed
on the Tire and Loading Information Label.
This label is attached to the vehicle’s center pillar
(B-pillar). SeeLoading Your Vehicle on page 277,
for more information about the Tire and Loading
Information Label and its location on your vehicle.
Different Size Tires and Wheels
If you add wheels or tires that are a different size
than your original equipment wheels and tires, this
may affect the way your vehicle performs, including
its braking, ride and handling characteristics,
stability, and resistance to rollover. Additionally,
if your vehicle has electronic systems such as,
anti-lock brakes, traction control, and electronic
stability control, the performance of these systems
can be affected.
{CAUTION:
If you add different sized wheels, your
vehicle may not provide an acceptable
level of performance and safety if tires
not recommended for those wheels are
selected. You may increase the chance
that you will crash and suffer serious
injury. Only use GM specic wheel and
tire systems developed for your vehicle,
and have them properly installed by a GM
certied technician.
SeeBuying New Tires on page 366and
Accessories and Modications on page 296for
additional information.
368

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your vehicle’s hazard warning ashers. SeeHazard
Warning Flashers on page 152for more information.
{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire. To
help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will
not move, you should put blocks at the
CAUTION: (Continued)
CAUTION: (Continued)
front and rear of the tire farthest away
from the one being changed. That would
be the tire, on the other side, at the
opposite end of the vehicle.
When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.
374

Removing the Spare Tire and Tools
The equipment you will need is located in
the trunk.
1. Open the trunk. SeeTrunk on page 102for
more information.
2. Remove the convenience net if the vehicle
has one.
3. Lift the handle on the spare tire cover. The
handle may hook on the front edge of the
trunk’s weatherstrip to hold the cover out of
the way.4. Turn the wing nut counterclockwise and
remove it.
5. Remove the compact spare tire.
375

6. Turn the nut holding the jack counterclockwise
and remove it. Then remove the jack and
wrench.The tools you will need to change a tire include
the jack (A), extension and protection guide (B),
and wheel wrench (C).
376

Removing the Flat Tire and
Installing the Spare Tire
Your vehicle may have aluminum wheels with
exposed wheel nuts. Use the wheel wrench to
loosen all the wheel nuts. Do not remove them yet.
Or, your vehicle may have steel wheel covers.
To remove the steel wheel covers and wheel nut
caps, loosen the plastic nut caps with the wheel
wrench in a counterclockwise direction. If needed,
you can nish loosening them with your ngers.
The plastic nut caps will not come off.Use the at end of the wheel wrench and pry
along the edge of the cover until it comes off.
The edge of the wheel cover could be sharp,
so do not try to remove it with your bare hands.
Do not drop the cover or lay it face down, as
it could become scratched or damaged. Store the
wheel cover in the trunk until you have the at
tire repaired or replaced.
Once you have removed the wheel cover, use the
following procedure to remove the at tire and
install the spare tire.
1. It is recommended that you do a safety check
before preceding. SeeChanging a Flat Tire
on page 374for more information.
2. Turn the wheel
wrench once on
each wheel nut to
loosen them. Do not
remove them yet.
377

{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off
the ground to install the compact spare tire.
6. Remove all wheel nuts and take off the at tire.
379

{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a
serious accident.
9. Reinstall the wheel
nuts with the
rounded end of the
nuts toward the
wheel. Tighten each
nut by hand until the
wheel is held against
the hub.10. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
381