2007 CADILLAC SRX Owners Manual

CAUTION: (Continued)
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
To be even more certain the vehicle will
not move, you should put blocks at the
front and rear of the tire farthest away
from the one being changed. That would
be the tire, on the other side, at the
opposite end of the vehicle.When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.
425

Removing the Spare Tire and Tools
The equipment you will need is located in the
rear of the vehicle. To access the equipment, do
the following:
1. Remove the storage bin to access the jack
if your vehicle has the cargo management
system.
If your vehicle has the third row seat, remove
the head rest storage tray to access the jack.
2. Turn the wing nut (A) holding the jack (B) (and
storage tray, if applicable) counterclockwise
and remove it.
3. Remove the jack and wheel wrench (C).
426

Removing the Spare Tire
The compact spare tire is located under the
vehicle, ahead of the rear bumper. SeeCompact
Spare Tire on page 442for more information
about the compact spare.
To remove the spare tire from the vehicle, do the
following:
A. Wheel Wrench
B. Cable
C. Retainer
D. Compact Spare Tire1. Open the liftgate. SeePower Liftgate on
page 104for more information.
2. Open the storage compartment door of the
cargo management system that is nearest
the liftgate and remove the container.
3. Attach the wheel wrench (A) into the hoist
shaft.
4. Turn the wheel wrench counterclockwise to
lower the spare tire to the ground. Continue
turning the wrench until the spare tire (D) can
be pulled out from under the vehicle.
427

5. Tilt the retainer (C) and slip it through the
wheel opening to remove the spare tire
from the cable (B).
6. Turn the wrench clockwise until you feel two
slips or hear two clicks after removing the
spare tire to raise the cable back up.
Do not store a full-size or a at road tire under
the vehicle. SeeStoring a Flat or Spare Tire
and Tools on page 439.To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 429.
If the spare tire will not lower, the secondary latch
may be engaged causing the tire not to lower.
Do the following to check the cable:
1. Check under the
vehicle to see if the
cable is visible. If
it is not visible, see
Secondary Latch
System on
page 436.
428

2. If it is visible, rst try to tighten the cable by
turning the wheel wrench clockwise until you
hear two clicks or feel it skip twice. You
cannot over-tighten the cable.
3. Loosen the cable then by turning the wrench
counterclockwise three or four turns.
4. Tighten the cable all the way and then loosen
it at least two times, if the spare tire has not
lowered.
If the spare tire did lower to the ground,
continue with Step 4 underRemoving the
Spare Tire and Tools on page 426.
If you still cannot lower the spare tire to the
ground, seeSecondary Latch System on
page 436.Removing the Flat Tire and
Installing the Spare Tire
To remove the at tire and install the spare, do
the following:
1. Loosen the wheel nuts, but do not remove
them yet, using the wheel wrench. Turn the
handle about 180 degrees, then ip the handle
back to the starting position. This avoids
taking the wrench off the lug nut for each turn.
429

2. Find the jacking
location using the
hoisting notches
located in the plastic
molding. The
notches in the
plastic molding are
marked with a
triangle shape to
help you nd them.
3. Attach the wheel wrench to the jack.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall.
To help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising the
vehicle.
430

{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
4. Turn the wheel wrench clockwise to raise the
jack lift head until the jack just ts under the
vehicle.5. Raise the jack by turning the wheel wrench
clockwise until the slots in the jack head t
into the metal ange located behind the
triangle on the plastic molding as shown.
Notice:Using a jack to raise the vehicle
without positioning it correctly could damage
your vehicle. When raising your vehicle on
a jack, be sure to position it correctly under the
frame and avoid contact with the plastic
molding.
431

6. Put the compact spare tire near you.
7. Raise the vehicle by turning the wheel wrench
clockwise. Raise the vehicle far enough off
the ground for the compact spare tire to
t under the vehicle.8. Remove all the wheel nuts and take off the
at tire.
9. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces and spare
wheel.
432