DOOR LOCK – DOOR CONTROL RECEIVERDL–109
DL
6. INSTALL TETHER ANCHOR BRACKET SUB-
ASSEMBLY (w/o Rear No. 2 Seat)
(a) Install the tether anchor bracket with the bolt.
7. INSTALL RECLINING REMOTE CONTROL LEVER
BEZEL RH (w/o Rear No. 2 Seat) (See page SE-105)
8. INSTALL REAR DECK TRIM COVER RH (w/ Rear No.
2 Seat)
(a) Attach the 4 claws to install the trim cover.
(b) Install the belt.
9. INSTALL REAR FLOOR FINISH PLATE (See page IR-
55)
10. INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE
PLATE (See page IR-55)
11. INSTALL REAR FLOOR NO. 3 BOARD
12. INSTALL REAR FLOOR NO. 2 BOARD
13. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear
No. 2 Seat) (See page SE-121)
14. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear
No. 2 Seat)
HINT:
Use the same procedures described for the LH side.
15. INSTALL NO. 2 SEAT LEG COVER LH (w/ Rear No. 2
Seat) (See page SE-123)
16. INSTALL NO. 2 SEAT LEG COVER RH (w/ Rear No. 2
Seat)
HINT:
Use the same procedures described for the LH side.
17. INSTALL NO. 2 SEAT HINGE COVER LH (w/ Rear No.
2 Seat) (See page SE-123)
18. INSTALL NO. 2 SEAT HINGE COVER RH (w/ Rear No.
2 Seat)
HINT:
Use the same procedures described for the LH side.
19. INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2
Seat)
20. INSTALL REAR FLOOR NO. 1 BOARD (w/o Rear No.
2 Seat)
21. INSTALL REAR DOOR OPENING TRIM
WEATHERSTRIP RH
B137550
SUPPLEMENTAL RESTRAINT SYSTEM – REAR AIRBAG SENSORRS–387
RS
20. REMOVE RECLINING REMOTE CONTROL LEVER
BEZEL LH (w/o Rear No. 2 Seat)
21. DISCONNECT REAR NO. 1 SEAT OUTER BELT
ASSEMBLY LH (See page SB-48)
22. DISCONNECT REAR NO. 2 SEAT OUTER BELT
ASSEMBLY LH (w/ Rear No. 2 Seat) (See page SB-48)
23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
(w/o Rear No. 2 Seat) (See page IR-32)
24. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
(w/ Rear No. 2 Seat) (See page IR-32)
25. REMOVE AIRBAG SENSOR REAR LH
(a) Disconnect the connector.
(b) Remove the bolt and airbag sensor.
B127923E01
RS–388SUPPLEMENTAL RESTRAINT SYSTEM – REAR AIRBAG SENSOR
RS
INSTALLATION
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
CAUTION:
Be sure to read the precautionary notices concerning the
SRS airbag system before servicing it (see page RS-1).
1. INSTALL AIRBAG SENSOR REAR LH
(a) Install the airbag sensor with the bolt.
Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf)
NOTICE:
• If the airbag sensor has been dropped, or
there are any cracks, dents or other defects in
the case, bracket or connector, replace it with
a new one.
• When installing the airbag sensor, be careful
that the SRS wiring does not interfere with
other parts and that it is not pinched between
other parts.
2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/
Rear No. 2 Seat) (See page IR-53)
3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/
o Rear No. 2 Seat) (See page IR-52)
4. CONNECT REAR NO. 2 SEAT OUTER BELT
ASSEMBLY LH (w/ Rear No. 2 Seat)
5. CONNECT REAR NO. 1 SEAT OUTER BELT
ASSEMBLY LH (See page SB-51)
6. INSTALL RECLINING REMOTE CONTROL LEVER
BEZEL LH (w/o Rear No. 2 Seat)
7. INSTALL REAR FLOOR FINISH PLATE (See page IR-
55)
8. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE
PLATE (See page IR-55)
9. INSTALL REAR FLOOR NO. 3 BOARD
10. INSTALL REAR FLOOR NO. 2 BOARD
11. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear
No. 2 Seat) (See page SE-121)
12. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear
No. 2 Seat) (See page IR-55)
13. INSTALL NO. 2 SEAT LEG COVER LH (w/ Rear No. 2
Seat) (See page SE-123)
14. INSTALL NO. 2 SEAT LEG COVER RH (w/ Rear No. 2
Seat) (See page IR-56)
15. INSTALL NO. 2 SEAT HINGE COVER LH (w/ Rear No.
2 Seat) (See page SE-123)
16. INSTALL NO. 2 SEAT HINGE COVER RH (w/ Rear No.
2 Seat) (See page IR-56)
B127923E01
