2006 SUZUKI SX4 Exhaus

Downloaded from www.Manualslib.com manuals search engine 1D-20 Engine Mechanical:
6) Install engine right mounting bracket (1) and engine
left mounting bush bolt (2), and then tighten bolt and
nuts to specified torque.
Tightening torque
Engine right mounting bracket nut (a): 65 N·m (
6.5 kgf-m, 47.0 lb-ft)
Engine right mounting bush bolt (b): 55 N·m (5.5
kgf-m, 40.0 lb-ft)
Engine left mounting bush bolt (c): 85 N·m (8.5
kgf-m, 61.5 lb-ft)
7) Install suspension frame mounting bolts (1) and front
lower cross member bolts (2). And then tighten bolts
to specified torque.
Tightening torque
Suspension frame mounting bolt (a): 150 N·m (
15.0 kgf-m, 108.5 lb-ft)
Front lower cross member bolt (b): 55 N·m (5.5
kgf-m, 40.0 lb-ft)8) Connect steering lower shaft from pinion shaft
referring to “Steering Lower Shaft Removal and
Installation in Section 6B”.
9) Connect propeller shaft referring to “Propeller Shaft
Assembly Removal and Installation in Section 3D”
(for 4WD model)
10) Install exhaust No.1, No.2 and center pipes referring
to “Exhaust System Components in Section 1K”.
11) Reverse disconnected hoses, cables and electric
wires for connection noting the following.
• Tighten bolts and nuts to specified torque.
Tightening torque
Starting motor terminal nut (a): 11 N·m (1.1 kgf-
m, 8.0 lb-ft)
Generator terminal nut (b): 5 N·m (0.5 kgf-m, 4.0
lb-ft)
Battery ground bolt (c): 25 N·m (2.5 kgf-m, 18.0
lb-ft)
Ground terminal bolt (d): 11 N·m (1.1 kgf-m, 8.0
lb-ft)
1
(b)(a)
2,(c)
I5RW0C140031-01
2,(b)
1,(a)
I5RW0A140016-01
[A]: For M/T model [B]: For A/T model
(d)
(a)
(b)
(c)
(c)
[A]
[B]
I5RW0C140013-02

Downloaded from www.Manualslib.com manuals search engine Engine Mechanical: 1D-21
12) Install oil pressure switch bracket (1).
13) Connect right and left drive shaft joints to differential
gear referring to “Front Drive Shaft Assembly
Removal and Installation in Section 3A”.
14) Install suspension control arm referring to
“Suspension Control Arm / Bushing Removal and
Installation in Section 2B”.
15) Install cylinder upper cover (1).16) Install A/C compressor to its bracket (if equipped)
referring to “Compressor Assembly Removal and
Installation in Section 7B” or “Compressor Assembly
Removal and Installation in Section 7B”.
17) Adjust A/C compressor drive belt referring to
“Compressor Drive Belt Removal and Installation in
Section 7B” or “Compressor Drive Belt Removal and
Installation in Section 7B”.
18) Install air cleaner assembly referring to “Air Cleaner
Assembly Removal and Installation”.
19) Check to ensure that all removed parts are back in
place. Reinstall any necessary parts which have not
been reinstalled.
20) Refill cooling system with coolant referring to
“Cooling System Flush and Refill in Section 1F”.
21) Refill engine with engine oil referring to “Engine Oil
and Filter Change in Section 0B”.
22) Refill transaxle oil referring to “Manual Transaxle Oil
Change in Section 5B” or “A/T Fluid Change in
Section 5A”.
23) Refill transfer oil referring to “Transfer Oil Change in
Section 3C”.
24) Install battery and battery tray with ECM.
25) Connect ECM wire harness.
26) Connect positive and negative cable at battery.
27) Install right and left side engine under covers.
28) Verify that there is no fuel leakage, coolant leakage,
oil leakage and exhaust gas leakage at each
connection.
2. Exhaust manifold
1
2
I5RW0A140011-01
1
I5RW0A140009-01

Downloaded from www.Manualslib.com manuals search engine Engine Mechanical: 1D-27
Timing Chain and Chain Tensioner ComponentsS6RW0D1406019
Timing Chain and Chain Tensioner Removal
and Installation
S6RW0D1406020
Removal
CAUTION!
After timing chain is removed, never turn
crankshaft and camshafts independently
more than its allowable turning range
described in “Installation”.
If turned, interference may occur between
piston and valves and valves themselves,
and parts related to piston and valves may be
damaged.

1) Remove timing chain cover referring to “Timing
Chain Cover Removal and Installation”.
2) By turning crankshaft, align camshafts and
crankshaft at specific position as follows.
a) Align both intake and exhaust camshaft timing
sprocket marks (1) with notches (2) of cylinder
head respectively.
b) Position crankshaft sprocket key (3) at upside of
crankshaft as shown in figure.
3) Remove timing chain tensioner adjuster assembly
(5).4) Remove timing chain tensioner (6).
5) Remove timing chain No.1 guide (7).
6) Remove timing chain (8) with crankshaft timing
sprocket (9).
I5RW0C140044-01
1. Crankshaft timing sprocket 5. Timing chain tensioner adjuster assembly : 25 N⋅m (2.5 kgf-m, 18.0 lb-ft)
2. Timing chain
: Apply engine oil.6. Chain tensioner adjuster mounting bolt : 11 N⋅m (1.1 kgf-m, 8.0 lb-ft)
3. Timing chain No.1 guide
: Apply engine oil to sliding surface.7. Timing chain tensioner bolt
4. Timing chain tensioner
: Apply engine oil to sliding surface.8. Timing chain No.1 guide bolt
3
1
1
2
5
67
8
9
I5RW0C140016-01

Downloaded from www.Manualslib.com manuals search engine 1D-28 Engine Mechanical:
Installation
CAUTION!
After timing chain is removed, never turn
crankshaft and camshafts independently
more than such an extent (“a”, “b”) as shown
in figure.
If turned, interference may occur between
piston and valves and valves themselves,
and parts related to piston and valves may be
damaged.

1) Check that match marks (1) on intake and exhaust
camshaft timing sprockets are in match with notches
(2) on cylinder head as shown in figure.
2) Set key (3) and turn crankshaft to position key on
upside of crankshaft.3) Install timing chain to camshaft timing sprockets as
follows.
• For engine with VVT
Install timing chain by aligning dark blue plates (1)
of timing chain and triangle mark (2) on camshaft
timing sprockets.
• For engine without VVT
Install timing chain by aligning dark blue plates (1)
of timing chain and circle mark (5) on intake
camshaft timing sprocket and triangle mark (5) on
exhaust camshaft timing sprocket.
4) Fit crankshaft timing sprocket to timing chain by
aligning gold plate (3) of timing chain and circle mark
(4) on crankshaft timing sprocket. Then install
crankshaft timing sprocket fitted with chain to
crankshaft.
“a”: 90°4. Camshaft (IN and EX) allowable turning range.
By marks on camshaft timing sprocket within 15° from notches
on cylinder head on both right and left.
“b”: 15°5. Crankshaft allowable turning range.
By key on crankshaft, within 90° from top on both right and left.
“a”
“b” “b”“b” “b”
“a”
1
12
4
3
5
I4RS0A140021-01
[A]: For engine with VVT [B]: For engine without VVT
34
1 1
Approx. 60 Approx. 30 [A]
1
Appro x. 60 Approx. 30 1 [B]
2
2
2
5
I5RW0C140018-01

Downloaded from www.Manualslib.com manuals search engine Engine Mechanical: 1D-29
5) Apply engine oil to sliding surface of timing chain
No.1 guide (1) and install it as shown in figure.
Tighten guide bolts to specified torque.
Tightening torque
Timing chain No.1 guide bolt (a): 11 N·m (1.1
kgf-m, 8.0 lb-ft)
6) Apply engine oil to sliding surface of chain tensioner
(1) and install chain tensioner and spacer.
Tighten tensioner bolt to specified torque.
Tightening torque
Timing chain tensioner bolt (a): 25 N·m (2.5 kgf-
m, 18.0 lb-ft)7) Check that triangle mark (2) and/or circle mark (5) on
intake and exhaust camshaft timing sprockets are in
match with dark blue plates (1) of timing chain and
match mark (4) on crankshaft timing sprocket is in
match with gold plate (3) of timing chain.
I2RH0B140062-01
I2RH0B140063-01
[A]: For engine with VVT [B]: For engine without VVT
2
1
Appro x. Approx.
1 [B]
34
1 12
2
Approx. Approx.
C [A]
[C]
I4RS0B140012-04

Downloaded from www.Manualslib.com manuals search engine 1D-30 Engine Mechanical:
8) Screw in plunger (1) by turning body (2) in arrow
direction and install a retainer (3) (wire) to hold
plunger in place.
9) Install timing chain tensioner adjuster assembly (1)
with a retainer (2).
Tighten adjuster bolts to specified torque and then
remove a retainer from chain tensioner adjuster
assembly.
Tightening torque
Timing chain tensioner adjuster bolt (a): 11 N·m
(1.1 kgf-m, 8.0 lb-ft)10) Apply engine oil to timing chain, and then turn
crankshaft clockwise by 2 revolutions and check that
match marks (1) are at the following specific
positions.
• Intake and exhaust camshaft timing sprockets are
in match with notches (2) on cylinder head.
• Crankshaft sprocket key (3) is on upside of
crankshaft as shown in figure.
11) Install timing chain cover referring to “Timing Chain
Cover Removal and Installation”.
12) Perform Steps 10) to 14) of “Installation” of “Timing
Chain Cover Removal and Installation”.
I2RH0B140065-01
I2RH0B140066-01
[A]: For engine with VVT [B]: For engine without VVT
1
1
2
3
21
1
3
[A]
[B]
I5RW0C140022-01

Downloaded from www.Manualslib.com manuals search engine 1D-32 Engine Mechanical:
Camshaft, Tappet and Shim ComponentsS6RW0D1406022
I4RS0B140014-03
[A]: For engine with VVT 4. Exhaust camshaft 9. Camshaft bearing
: Install a bearing half with some holes to upper side of intake
camshaft No.1 bearing.
[B]: For engine without VVT 5. Shim
: Shim No. on it faces tappet side.: 60 N⋅m (6.0 kgf-m, 43.5 lb-ft)
1. Intake camshaft 6. Tappet : Tighten 11 N⋅m (1.1 kgf-m, 8.0 lb-ft) by the specified procedure
2. Intake camshaft sprocket assembly 7. Camshaft housing : Apply engine oil to sliding surface of each part.
3. Intake camshaft sprocket bolt 8. Camshaft housing bolt

Downloaded from www.Manualslib.com manuals search engine Engine Mechanical: 1D-33
Camshaft, Tappet and Shim Removal and
Installation
S6RW0D1406023
CAUTION!
• Keep working table, tools and hands clean
while overhauling.
• Use special care to handle aluminum parts
so as not to damage them.
• Do not expose removed parts to dust.
Keep them always clean.

Removal
1) Remove timing chain cover referring to “Timing
Chain Cover Removal and Installation”.
2) Remove timing chain referring to “Timing Chain and
Chain Tensioner Removal and Installation”.
3) For engine with VVT, with hexagonal section (1) of
intake camshaft (2) held stationary with spanner or
the like, loosen mounting bolt of intake cam timing
sprocket assembly (3) and remove it.
CAUTION!
Never attempt to loosen mounting bolt with
intake cam timing sprocket assembly held
stationary. Failure to follow this could result
in damage to lock pin.
Do not loosen bolt “a” because intake cam
timing sprocket assembly is not serviceable.

4) Loosen camshaft housing bolts in such order as
indicated in figure and remove them.
5) Remove camshaft housings.
6) Remove intake and exhaust camshafts.
7) For engine with VVT, remove camshaft bearings (1).
8) Remove tappets (2) with shims (1).
3“a”
1
2
I3RM0A140030-01
“12”“13”
“20”“21”
“16”“17” “8”“9”
“2”
“5”
“3”
“4”
“1”
“10”
“11”“18”
“19” “14”“15” “6” “7”
I3RM0A140031-01
I5RW0C140023-01
I2RH0B140074-01