2006 SUZUKI SX4 PPL

Downloaded from www.Manualslib.com manuals search engine Transfer: 3C-2
Repair Instructions
Transfer Oil Level CheckS6RW0D3306001
1) Lift up vehicle and check oil leakage. Repair leaky
point, if any.
2) Remove oil level / filler plug (1) and check oil
contamination and oil level is lower end of oil level /
filler plug hole (2).
If oil is excessive dirty or insufficient, replace oil or
pour specified oil up to plug hole.
3) Apply sealant to thread of level / filler plug, and then
tighten it to specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Transfer oil level / filler plug (a): 23 N·m (2.3 kgf-
m, 17.0 lb-ft)
Transfer Oil ChangeS6RW0D3306002
1) Before changing or inspecting oil, be sure to stop
engine and lift vehicle horizontally.
2) Check leakage.
If leakage exists, correct it.
NOTE
Whenever vehicle is hoisted for any other
service work than oil change, also be sure to
check for oil leakage.

3) Remove oil filler plug (2).
4) Remove drain plug (1), and drain oil.5) Apply sealant to thread of drain plug (1), and tighten
it to specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Transfer oil drain plug (a): 23 N·m (2.3 kgf-m,
17.0 lb-ft)
6) Pour new specified oil up to lower end of oil level /
filler plug hole (3).
NOTE
It is highly recommended to use API GL-5
80W-90 gear oil.

Transfer oil specification
: API GL-5 (For SAE classification, refer to
viscosity chart [A] in figure.)
Transfer oil capacity
Reference: 0.6 liters (1.2/1.0 US/lmp. pt)
7) Apply sealant to thread of level / filler plug, and then
tighten it to specified torque.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
Tightening torque
Transfer oil level / filler plug (b): 23 N·m (2.3 kgf-
m, 17.0 lb-ft)
I5RW0A330002-01
I5RW0A330003-01

Downloaded from www.Manualslib.com manuals search engine 3C-3 Transfer:
Transfer Dismounting and RemountingS6RW0D3306003
Dismounting
1) Disconnect negative cable at battery.
2) Drain transaxle oil and transfer oil.
3) Remove drive shafts assembly referring to “Front
Drive Shaft Assembly Removal and Installation in
Section 3A”.
4) Remove exhaust No.1, No.2 and center pipes
referring to “Exhaust Pipe and Muffler Removal and
Installation in Section 1K”.
5) Remove suspension frame, engine front mounting
member and mounting member referring to “Front
Suspension Frame, Stabilizer Bar and/or Bushing
Removal and Installation in Section 2B” and “Engine
Assembly Removal and Installation in Section 1D”.
6) Remove engine rear mounting bracket (1) and
stiffeners (2) from transfer.
7) Support transfer with transmission jack.
8) Remove transfer to transaxle bolts (1), and then
lower transfer assembly (2).Remounting
Reverse dismounting procedure for remounting of
transfer, noting the following points.
• Apply grease to left case (1) as shown in figure.
“A”: Grease 99000–25010 (SUZUKI Super Grease
A)
• Tighten engine rear mounting bracket nut to specified
torque referring to “Engine Mountings Components in
Section 1D”.
• Tighten bolts to specified torque as follows.
Tightening torque
Stiffener No.1 bolt and No.2 bolt (a): 55 N·m (5.5
kgf-m, 40.0 lb-ft)
Transfer to transaxle bolt (b): 98 N·m (9.8 kgf-m,
71.0 lb-ft)
2
2
1I5RW0A330004-01
1
1
2
I5RW0A330005-02
I5RW0C330001-01
(a)
(a)
(b)
(b)
2
I5RW0A330006-02

Downloaded from www.Manualslib.com manuals search engine Transfer: 3C-4
• Pour transaxle oil and transfer oil referring to “Manual
Transaxle Oil Change in Section 5B” and “Transfer Oil
Change”.
Transfer Assembly ComponentsS6RW0D3306004
1
2
6
9
1110
8
7
3A
4
5
36
OIL
(a) 5
(a)
OIL
28
18
30
27
25
21
28
13
12
22OIL
OIL
32A
31A
1322(d)
34A
33
23A
2019
(c)1217G
291217G
(b)
35
15A
26
26 14
24
17
161217G(b)
A
I5RW0A330007-05
1. Transfer output flange nut
: After tightening nut so as rotational torque
of bevel pinion to be in specified value,
caulk nut securely.15. Dowel pin 29. Transfer right case
: Apply sealant 99000-31260 to
mating surface with right case.
2. Transfer output flange 16. Oil drain plug
: Apply sealant 99000-31260 to thread
part.30. Oil level / filler plug
: Apply sealant 99000-31260 to
thread part.
3. Oil seal
: Apply grease 99000-25010 to oil seal lip.17. Transfer left case
: Apply grease 99000-25010 to left case.31. Left case oil seal No.1
: Apply grease 99000-25010 to oil
seal lip.
4. Pinion shaft rear taper roller bearing 18. Transfer case bolt 32. Left case oil seal No.2
: Apply grease 99000-25010 to oil
seal lip.
5. Transfer output retainer bolt 19. Reduction drive gear left bearing 33. Right case oil seal No.3
: Apply grease 99000-25010 to oil
seal lip.
6. O-ring
: Apply grease 99000-25010 to all around
surface.20. Reduction drive gear 34. Right case oil seal No.2
: Apply grease 99000-25010 to oil
seal lip.
7. Shim 21. Reduction driven gear left taper roller
bearing35. Right case oil seal No.1
: Apply grease 99000-25010 to oil
seal lip.
8. Spacer 22. Reduction driven gear right taper roller
bearing36. Transfer output retainer

Downloaded from www.Manualslib.com manuals search engine 3C-5 Transfer:
Transfer Assembly Disassembly and
Reassembly
S6RW0D3306005
Disassembly
NOTE
It is possible to disassemble transfer
assembly without removing intermediate
shaft with Step 1) to 4) performed if not
necessary.

1) Remove right case oil seal No.1 (1) from transfer
right case using special tool.
Special tool
: 09913–50121
2) Remove snap ring (2) by using snap ring pliers.
3) Remove intermediate shaft (4) with intermediate
shaft bearing (3) from transfer assembly.
4) Remove intermediate shaft bearing (3) from
intermediate shaft (4) by using bearing puller and
hydraulic press.
5) Remove transfer output retainer assembly (1) and
shim (3) by removing retainer bolts (2).
6) Remove transfer case bolts (4).
7) Separate transfer right case (5) from transfer left
case (6) by using special tool.
Special tool
(A): 09912–34510
8) Remove reduction drive gear assembly (7) and
reduction driven gear assembly (9).
9) Remove shim (10) and bearing outer races (8).
NOTE
When it is difficult to remove bearing outer
races from cases, remove them with special
tool.

Special tool
(B): 09944–96011Reassembly
1) Select appropriate shim as follows.
a) Measure distance “a” between taper roller
bearing outer races of reduction driven gear
assembly (1).
b) Measure depth “b” of left case (2) and “c” of right
case (3).
c) Obtain adjusting shim thickness by the following
equation.
9. Pump seal 23. Reduction drive gear right bearing : 55 N⋅m (5.5 kgf-m, 40.0 lb-ft)
10. Pinion shaft front taper roller bearing 24. Intermediate shaft : 21 N⋅m (2.1 kgf-m, 15.5 lb-ft)
11. Bevel pinion 25. Oil protect plate bolt
: Apply thread lock cement 99000-32110
to thread part.: 23 N⋅m (2.3 kgf-m, 17.0 lb-ft)
12. Bevel gear 26. Snap ring : 9 N⋅m (0.9 kgf-m, 6.5 lb-ft)
13. Reduction driven gear 27. Oil protect plate : Do not reuse.
14. Intermediate shaft bearing 28. Shim : Apply transfer oil.
4
3
2
1
I5RW0A330008-01
11. Dowel pin
Necessary
shim
thickness=Depth
“b”+Depth
“c”–Distanc
e “a”+0.1 mm
(0.004
in.)
7
(B)
5
11
310 9 10
8 64
8
(A)
12
2
I5RW0A330009-03
23
1
“b”
“a”“c”
I5RW0A330010-01

Downloaded from www.Manualslib.com manuals search engine Transfer: 3C-6
d) Select a shim which is close to half thickness of
the calculated value (necessary shim thickness)
from among the available shims to install it
between bearing and case at each of right and
left sides.
For example:
Measure distance “a” is 110.75 mm (4.360 in.).
Measure depth “b” is 85.8 mm (3.378 in.).
Measure depth “c” is 26.55 mm (1.045 in.).
Necessary shim thickness = 85.8 mm (3.378 in.)
+ 26.55 mm (1.045 in.) – 110.75 mm (4.360 in.) +
0.1 mm (0.004 in.) = 1.7 mm (0.067 in.)
1.7 mm (0.067 in.) ÷ 2 = 0.85 mm (0.033 in.)
Calculated thickness of new shim = 0.85 mm
(0.033 in.)
Available reduction driven gear shim
thickness
0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90, 0.95,
1.00 and 1.05 mm (0.024, 0.026, 0.028, 0.030,
0.031, 0.033, 0.035, 0.037, 0.039 and 0.041 in.)
2) Clean mating surface of right and left cases, and
apply sealant to right case (1) as shown in figure by
such amount that its section is 1.2 mm (0.047 in.) in
diameter.
“A”: Sealant 99000–31260 (SUZUKI Bond
No.1217G)
3) Assemble the following parts in right and left cases
by reversing disassembling procedure.
• Reduction drive gear assembly (1)
• Reduction driven gear assembly (3)
• Bearing outer races (2)
• Reduction driven gear shims (5)
• Dowel pin (6)
4) Tighten transfer case bolts (4) to specified torque.
Tightening torque
Transfer case bolt (a): 23 N·m (2.3 kgf-m, 17.0 lb-
ft)5) Select bevel pinion shim (3) referring to step 1) of
“Reassembly” under “Transfer Output Retainer
Assembly Disassembly and Reassembly”.
6) Inspect tooth contact according to “Bevel Gear Tooth
Contact Inspection”.
7) Install transfer output retainer assembly (2) with
bevel pinion shim (3) to transfer left case (4) by
tightening retainer bolt (1) to specified torque.
Tightening torque
Transfer output retainer bolt (a): 55 N·m (5.5 kgf-
m, 40.0 lb-ft)
8) Install bolt to bolt hole of flange (2), set dial gauge
measuring tip at right angles to bolt (1) as shown in
figure. Holding reduction driven gear by hand, take
measurement backlash of pinion and bevel gear.
NOTE
If backlash exceeds specification given
below, adjust it by changing thickness ratio
of shims assembled in right and left cases in
Step 3).

Special tool
(A): 09900–20607
(B): 09900–20701
Bevel pinion & bevel gear backlash
: 0.1 – 0.2 mm (0.0039 – 0.0078 in.)
1
“A”
I5RW0A330011-01
6
4, (a) 5 2
31
2
5
I5RW0A330012-02
4
3
21, (a)
1, (a)
I5RW0A330013-02
(A)
1
(B)
2
I5RW0A330014-02

Downloaded from www.Manualslib.com manuals search engine 3C-7 Transfer:
9) Install intermediate shaft bearing (1) to intermediate
shaft (2) by using special tool.
Special tool
(A): 09913–84510
10) Install intermediate shaft (2) with bearing (3) in
transfer.
11) Install new snap ring (1) to transfer right case by
using snap ring pliers.
12) Apply grease to new right case oil seal No.1 lip.
“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
13) Drive right case oil seal No.1 (1) in transfer right
case (2) by using special tool and hammer.
Special tool
(A): 09925–15410
Intermediate output oil seal installing depth
“a”: 1.0 – 1.5 mm (0.04 – 0.06 in.)
Reduction Drive Gear Assembly Disassembly
and Reassembly
S6RW0D3306006
Disassembly
Remove bearings (1) from reduction drive gear (2) using
special tool, bearing puller (3) and hydraulic press (4).
Special tool
(A): 09913–85230
Reassembly
1) Clean all components thoroughly, inspect them for
any abnormality and replace with new one as
necessary.
2) Install bearings (1) to reduction drive gear (2) using
special tool, bearing puller (3) and hydraulic press
(4).
Special tool
(A): 09913–85230
(A)
1
2
I5RW0A330015-01
132
I5RW0A330016-02
(A)
1, “A”
2
2
“a”
I5RW0A330017-02
4
(A)2
1
3I5RW0A330018-01
(A)
2
4
1
3I5RW0A330019-01

Downloaded from www.Manualslib.com manuals search engine 3C-9 Transfer:
3) Install left bearing (1) to reduction driven gear (2)
using special tools and hydraulic press.
Special tool
(A): 09913–84510
(B): 09924–84510–005
Transfer Right Case and Left Case Disassembly
and Reassembly
S6RW0D3306008
Disassembly
1) Remove oil seals from right case (1) using special
tool, if necessary.
Special tool
(A): 09925–15410
2) Remove oil plate (1) from right case (2), if necessary.
3) Remove oil seals from left case using flat end rod or
the like, if necessary.Reassembly
1) When installing oil seal No.2 (1) and No.3 (2) to right
case (3) using special tool, use care so that oil seals
in proper direction and position as shown in figure.
Apply grease to oil seal lip.
Special tool
(A): 09925–15410
“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
Oil seals installing depth
“a”: 23.5 – 24.0 mm (0.925 – 0.945 in.)
“b”: 38.0 – 39.0 mm (1.496 – 1.535 in.)
2) Install oil plate to right case.
Tightening torque
Oil plate bolt: 9 N·m (0.9 kgf-m, 6.5 lb-ft)
3) When installing new oil seal No.1 (1) and No.2 (2) to
left case (3) using special tool, use care so that oil
seals in proper direction as shown in figure.
Apply grease to oil seal lip.
Special tool
(A): 09913–85210 (For oil seal No.1)
(A): 09944–88210 (For oil seal No.2)
“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
(A)
1
2
(B)I5RW0A330025-02
(A)
1
I5RW0A330026-01
1
2
I5RW0A330027-01
1, “A”
2, “A”“a”
(A)
3 “b”
I5RW0A330028-01
3
(A)
2, “A”1, “A”I5RW0A330029-01

Downloaded from www.Manualslib.com manuals search engine 3C-13 Transfer:
2) Press-fit outer races (front and rear) by using special
tool and hydraulic press.
Special tool
(A): 09913–75520
3) Press-fit front taper roller bearing (1) by using
special tool and hydraulic press.
Special tool
(A): 09925–18011
4) Install bevel pinion with new pinion shaft spacers (1)
and new pump seal (2) to transfer output retainer (3).5) Drive in rear taper roller bearing by using special tool
and tapping lightly with plastic hammer.
Special tool
(A): 09913–84510
6) Apply grease to new oil seal lip.
“A”: Grease 99000–25010 (SUZUKI Super
Grease A)
7) Drive in oil seal (1) by using special tools and
hammer.
Special tool
(A): 09940–54910
(B): 09913–76010
Transfer output flange oil seal installing depth
“a”: 21.0 – 22.0 mm (0.82 – 0.86 in.)
(A)
I5RW0A330038-01
(A)
1
I5RW0A330039-01
1
2
3
I5RW0A330040-02
(A)
I5RW0A330041-02
(B)
(A)
1, “A”
“a”
I5RW0A330042-02