2006 NISSAN VERSA ignition

REAR WINDOW DEFOGGER
GW-59
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: June 20062007 Versa
5. CHECK CONDENSER
Check continuity between condenser terminals.
OK or NG
OK >> GO TO 6.
NG >> Replace condenser.
6. CHECK CONDENSER HARNESS CONTINUITY
1. Disconnect IPDM E/R.
2. Check continuity between condenser connector and IPDM E/R
connector.
3. Check continuity between condenser connector and ground.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace harness.
7. CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1. Connect IPDM E/R.
2. Turn ignition switch ON.
3. Check voltage between IPDM E/R connector E48 terminal 60
and ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace IPDM E/R. Refer to PG-29, "
Removal and Installation of IPDM E/R" .
AB
Continuity
Terminal Terminal
12Yes
PIIB6487E
AB
Continuity
Connector Terminal Connector Terminal
D409 1 E48 60 Yes
A
GroundContinuity
Condenser
connectorTerminal
D409 1 No
LIIA2644E
ConnectorTe r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
E48 60 GroundRear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF0
LIIA2190E

GW-60
REAR WINDOW DEFOGGER
Revision: June 20062007 Versa
Door Mirror Defogger Circuit CheckEIS009CX
1. CHECK FUSE
Check if the following fuse in the fuse block (J/B) is blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2. CHECK HEATED MIRROR RELAY POWER SUPPLY CIRCUIT
1. Disconnect heated mirror relay.
2. Turn ignition switch ON.
3. Check voltage between heated mirror relay connector and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK HEATED MIRROR RELAY GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between heated mirror relay connector M48
terminal 2 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. INSPECTION OF HEATED MIRROR RELAY
Check continuity between heated mirror relay terminals 3 and 5.
OK or NG
OK >> GO TO 5.
NG >> Replace heated mirror relay.
Component Parts Ampere Fuse No.
Fuse block (J/B) 10A 5
ConnectorTe r m i n a l s
Voltage (V)
(Approx.)
(+) (-)
M481
Ground Battery voltage
3
LIIA2647E
2 - Ground : Continuity should exist.
LIIA2646E
Condition Continuity
12V direct current supply between
terminals 1 and 2Ye s
No current supply No
SEF 1 45 X

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Collision diagnosis .......................................... SRS-54
Combination lamp, rear, removal and installation LT-87
Combination meter ................................................ DI-5
Combination meter removal and installation - See Instru-
ment panel .......................................................... IP-11
COMBSW - Wiring diagram ............................... LT-67
Component Location (manual A/C) ................ MTC-25
Compression pressure ...................................... EM-62
Compressor mounting .................................... MTC-84
Compressor special service tool .................... MTC-12
Condenser ...................................................... MTC-88
Connecting rod .................................................. EM-97
Connecting rod bearing clearance .................. EM-101
Connecting rod bushing clearance .................... EM-97
CONSULT for ABS .......................................... BRC-20
CONSULT general information .......................... GI-37
CONSULT-II for engine ................................... EC-113
CONSULT-II function (EPS) ............................ STC-13
CONSULT-II Reference value (CVT) .............. CVT-57
Control lever (M/T) ............................................ MT-12
Control units (terminal arrangement) ................ PG-72
Control valve (CVT) ......................................... CVT-29
Converter housing installation ............ AT-254, AT-369
COOL/F - Wiring diagram ............................... EC-448
Coolant mixture ratio ......................................... MA-12
Cooling circuit (engine) ....................................... CO-7
Cooling fan ........................................................ CO-15
Cooling fan motor ............................................ EC-443
Corrosion protection ......................................... BL-237
Coupling sleeve (M/T) ....................................... MT-18
Crankcase ventilation system - See Positive crankcase
ventilation .......................................................... EC-44
Crankshaft ......................................................... EM-77
Crankshaft position sensor (POS) ................... EC-319
Crash zone sensor .......................................... SRS-49
CVT air breather hose ................................... CVT-205
CVT control system ......................................... CVT-22
CVT cross-sectional view ................................ CVT-21
CVT Electrical parts location ........................... CVT-40
CVT fluid checking ............... CVT-16, CVT-43, MA-20
CVT fluid cooler cleaning ................................ CVT-18
CVT fluid replacement ........................ CVT-17, MA-21
CVT fluid temparature sensor ......................... CVT-85
CVT hydraulic control system ......................... CVT-23
CVT indicator ...................................................... DI-42
CVT self-diagnoses ........................... CVT-60, CVT-67
CVT shift lock system .................................... CVT-197
CVT trouble diagnoses .................................... CVT-34
CVTIND - Wiring diagram ................................... DI-43
Cylinder block .................................................... EM-77
Cylinder head .................................................... EM-62
Cylinder head bolt tightening ............................. EM-65
D
D/LOCK - Wiring diagram ...................... BL-26
, BL-31
Data link connector ............. EC-115, EC-127, EC-592
DEF - Wiring diagram ....................................... GW-52
Diagnosis sensor unit ...................................... SRS-52
Diagnostic trouble code (DTC) for OBD system . EC-8,
EC-48
Diagnostic trouble code (DTC) inspection priority chart
EC-89
, CVT-34
Differential gear (FF M/T) .................................. MT-22
Differentil side oil seal .................................... CVT-206
DLC - Wiring diagram ...................................... EC-592
Door glass .......................................... GW-43, GW-47
Door glass Fitting Adjustment(Front) ................ GW-46
Door glass Fitting Adjustment(Rear) ................ GW-49
Door mirror ....................................................... GW-65
Door trim .............................................................. EI-27
Door, front ......................................................... GW-43
Door, rear ......................................................... GW-47
Drive shaft ......................................................... MA-27
Driver air bag ................................................... SRS-41
Dropping resistor (A/T) .................................... AT-150
DTC work support ............................................ EC-122
DTRL - Wiring diagram ....................................... LT-31
Duct and grilles ............................................... MTC-75
E
ECM input/output signal .................................. EC-105
ECM power supply .......................................... EC-144
ECTS - Wiring diagram .................................... EC-202
Electric sunroof .................................................. RF-10
Electric throttle control actuator .. EM-18, EC-499, EC-
506, EC-511
Electrical load signal circuit ............................. EC-562
Electrical unit ..................................................... PG-72
Electrical units location ...................................... PG-64
Electronic ignition (EI) system ........................... EC-25
Electronic key ..................................................... BL-80
ENG SS - Wiring diagram ................................ AT-114
Engine control circuit diagram ......................... EC-103
Engine control component parts location .......... EC-96
Engine control module (ECM) ......................... EC-427
Engine control system diagram ......................... EC-22
Engine coolant ..................................................... CO-8
Engine coolant temperature sensor (ECTS) ... EC-200,
EC-212
Engine fail-safe system ..................................... EC-91
Engine oil ............................................................. LU-5
Engine oil precautions .......................................... GI-7
Engine removal .................................................. EM-73
EPS - Wiring diagram ........................................ STC-9
EPS control unit input/output signal reference values ..
STC-11
EPS system description ..................................... STC-5
EPS system diagram ......................................... STC-6
ETC1 - Wiring diagram .................................... EC-500
ETC2 - Wiring diagram .................................... EC-495
ETC3 - Wiring diagram .................................... EC-507
EVAP canister ................................................... EC-34
EVAP canister purge volume control solenoid valve ....
EC-354
, EC-362
EVAP canister vent control valve ...... EC-369, EC-376
EVAP control system (small leak) diagnosis .. EC-346,

IDX-4
ALPHABETICAL INDEX
EC-398, EC-406
EVAP control system pressure sensor .... EC-382, EC-
385, EC-391
EVAP control system purge flow monitoring diagnosis
EC-340
EVAP vapor lines inspection ............................. MA-19
Evaporative emission (EVAP) system ............... EC-31
Evaporator ...................................................... MTC-90
Exhaust manifold .............................................. EM-21
Exhaust system inspection ................... MA-20, MA-22
Expansion valve .............................................. MTC-91
F
F/FOG - Wiring diagram ..................................... LT-43
F/PUMP - Wiring diagram ................................ EC-571
Final drive (FF M/T) ........................................... MT-22
Floor trim ............................................................. EI-37
Flow charts ......................................................... GI-27
Fluid temparature sensor (CVT) ...................... CVT-85
Fluid temperature sensor (A/T) ........................ AT-106
Fluids ................................................................ MA-11
Fluorescent leak detector ............................... MTC-92
Flywheel (clutch) ................................................ CL-13
Flywheel runout .............................................. EM-103
Fork rod (M/T) .................................................... MT-21
Freeze frame data ............................... EC-52, EC-116
Front bumper ...................................................... EI-14
Front door ......................................................... GW-43
Front passenger air bag .................................. SRS-46
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-51
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ......................... AT-103, CVT-86
FTTS - Wiring diagram ...................... EC-293, EC-298
FUEL - Wiring diagram ...................... EC-278, EC-286
Fuel cut control (at no load high engine speed) . EC-26
Fuel gauge ............................................................ DI-5
Fuel injection system ......................... EC-276, EC-284
Fuel injector ..................................................... EC-564
Fuel injector and fuel tube ................................ EM-33
Fuel level sensor ................. EC-415, EC-417, EC-419
Fuel line inspection .................................. FL-4, MA-15
Fuel precautions ................................................... GI-6
Fuel pressure check .......................................... EC-81
Fuel pressure release ........................................ EC-81
Fuel pump ........................................................ EC-570
Fuel systemCommercial Service Tools ................ FL-3
Fuel systemPREPARATION ................................. FL-3
Fuel tank temperature sensor ............ EC-291, EC-297
Fuel tank vacuum relief valve ............................ EC-34
Fuse ................................................................... PG-16
Fuse and fusible link box ................................... PG-77
Fusible link ......................................................... PG-16
G
Gauges ................................................................. DI-5
Gear components (M/T) .................................... MT-18
Generic scan tool (GST) ................................. EC-126
Glass ...................................... GW-11, GW-43, GW-47
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-30
H
H/LAMP - Wiring diagram .................................... LT-8
H/PHON - Wiring diagram .................................. AV-52
Handling precautions for plastics ..................... BL-255
Harness connector ............................................ PG-68
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-51
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 2 ..... EC-248, EC-257, EC-267
Heated oxygen sensor 2 heater ...................... EC-166
HEATER - Wiring diagram .............................. MTC-28
Heater system - Wiring diagram ..................... MTC-28
HFC134a (R134a) system precaution .............. MTC-4
HFC134a (R134a) system service procedure . MTC-80
HFC134a (R134a) system service tools ......... MTC-12
HFC134a system service equipment precaution MTC-9
HO2S2 - Wiring diagram ..... EC-251, EC-260, EC-270
HO2S2H - Wiring diagram .............................. EC-168
Horn ................................................................. WW-46
HORN - Wiring diagram ................................... WW-46
How to erase DTC for OBD system .................. EC-60
I
IATS - Wiring diagram ..................................... EC-197
Idle air volume learning ..................................... EC-78
Idle speed ......................................................... EC-75
Idle speed control (ISC) .................... EC-423, EC-425
Ignition coil ...................................................... EC-576
Ignition control system .................................... EC-576
Ignition timing .................................................... EC-75
IGNSYS - Wiring diagram ............................... EC-577
ILL - Wiring diagram ......................................... LT-111
Illumination control ........................................... LT-108
In-cabin Microfilter ............................................. MA-20
INJECT - Wiring diagram ................................ EC-565
Input shaft (FF M/T) .......................................... MT-18
Input/Output signal of TCM ............................. CVT-25
Instrument panel ................................................. IP-10
INT/L - Wiring diagram ....................................... LT-96
Intake air temperature sensor ........... EC-195, EC-215
Intake door control linkage adjustment ........... MTC-69
Intake manifold .................................................. EM-18
Intake valve timing control .............................. EC-156
Intake valve timing control solenoid valve ....... EC-173
Interior ................................................................. EI-32
Interior lamp ....................................................... LT-91
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-174

PRECAUTIONS
LAN-3
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: June 20062007 Versa
PRECAUTIONSPFP:00001
Precautions When Using CONSULT-IIUKS005XZ
Use CONSULT-II CONVERTER when connecting CONSULT-II to data link connector.
CAUTION:
CAN communication does not function properly if CONSULT-II is used without connecting CONSULT-II
CONVERTER.
Precautions for Trouble DiagnosisUKS005Y0
CAUTION:

Never apply 7.0 V or more to the measurement terminal.

Use a tester with open terminal voltage of 7.0 V or less.

Turn the ignition switch OFF and disconnect the battery cable from the negative terminal when
checking the harness.
Precautions for Harness RepairUKS005Y1

Solder the repaired area and wrap tape around the soldered
area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).

Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause CAN communication error. The
spliced wire becomes separated and the characteristics of
twisted line are lost.

Replace the applicable harness as an assembly if error is detected on the shield lines of CAN communi-
cation line.
SKIB8766E
SKIB8767E

TROUBLE DIAGNOSIS
LAN-7
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: June 20062007 Versa
TROUBLE DIAGNOSISPFP:00004
Condition of Error DetectionUKS005Y4
“U1000” or “U1001” is indicated on SELF-DIAG RESULTS on CONSULT-II if CAN communication signal is not
transmitted or received between units for 2 seconds or more.
CAN COMMUNICATION SYSTEM ERROR

CAN communication line open (CAN-H, CAN-L, or both)

CAN communication line short (ground, between CAN communication lines, other harnesses)

Error of CAN communication control circuit of the unit connected to CAN communication line
WHEN INDICATED “U1000” OR “U1001” IS INDICATED EVEN THOUGH CAN COMMUNICA-
TION SYSTEM IS NORMAL

CONSULT-II CONVERTER not connected: Error may be detected by the self-diagnosis when not using
CONSULT-II CONVERTER (Depending on the control unit which carries out CAN communication).

Removal/installation of parts: Error may be detected when removing and installing CAN communication
unit and related parts while turning the ignition switch ON. (A DTC except for CAN communication may be
detected.)

Fuse blown out (removed): CAN communication of the unit may cease.

Voltage drop: Error may be detected if voltage drops due to discharged battery when turning the ignition
switch ON (Depending on the control unit which carries out CAN communication).

Error may be detected if the power supply circuit of the control unit, which carries out CAN communica-
tion, malfunctions (Depending on the control unit which carries out CAN communication).

Error may be detected if reprogramming is not completed normally.
NOTE:
CAN communication system is normal if “U1000” or “U1001” is indicated on SELF-DIAG RESULTS of CON-
SULT-II under the above conditions. Erase the memory of the self-diagnosis of each unit.

LAN-10
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Example: Main Line Between Data Link Connector and ABS Actuator and Electric Unit (Con-
trol Unit) Open Circuit
SKIB8740E
Unit name Symptom
ECM Engine torque limiting is affected, and shift harshness increases.
BCM

Reverse warning chime does not sound.

The front wiper moves under continuous operation mode even though the front
wiper switch being in the intermittent position.
EPS control unit The steering effort increases.
Combination meter

The shift position indicator and OD OFF indicator turn OFF.

The speedometer is inoperative.

The odo/trip meter stops.
ABS actuator and electric unit (control unit) Normal operation.
TCM No impact on operation.
IPDM E/RWhen the ignition switch is ON,

The headlamps (Lo) turn ON.

The cooling fan continues to rotate.

TROUBLE DIAGNOSIS
LAN-11
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: June 20062007 Versa
Example: CAN-H, CAN-L Harness Short Circuit
SKIB8741E
Unit name Symptom
ECM

Engine torque limiting is affected, and shift harshness increases.

Engine speed drops.
BCM

Reverse warning chime does not sound.

The front wiper moves under continuous operation mode even though the front
wiper switch being in the intermittent position.

The room lamp does not turn ON.

The engine does not start (if an error or malfunction occurs while turning the igni-
tion switch is OFF.)

The steering lock does not release (if an error or malfunction occurs while turning
the ignition switch is OFF.)
EPS control unit The steering effort increases.
Combination meter

The tachometer and the speedometer do not move.

Warning lamps turn ON.

Indicator lamps do not turn ON.
ABS actuator and electric unit (control unit) Normal operation.
TCM No impact on operation.
IPDM E/RWhen the ignition switch is ON,

The headlamps (Lo) turn ON.

The cooling fan continues to rotate.