2006 NISSAN VERSA height

DTC P2A00 A/F SENSOR 1
EC-547
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 Versa
11 . REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace air fuel ratio (A/F) sensor 1.
CAUTION:

Discard any air fuel ratio (A/F) sensor which has been dropped from a height of more than 0.5 m
(19.7 in) onto a hard surface such as a concrete floor; use a new one.

Before installing new air fuel ratio (A/F) sensor, clean exhaust system threads using Heated Oxy-
gen Sensor Thread Cleaner tool J-43897-18 or J-43897-12 and approved anti-seize lubricant.
>> GO TO 12.
12. CONFIRM A/F ADJUSTMENT DATA
1. Turn ignition switch ON.
2. Select “A/F ADJ-B1” in “DATA MONITOR” mode with CON-
SULT-II.
3. Make sure that “0.000” is displayed on CONSULT-II screen.
OK or NG
OK >>INSPECTION END
NG >> GO TO 13.
PBIB3201E

EM-2Revision: June 20062007 Versa Components ........................................................... 37
Removal and Installation ........................................ 38
REMOVAL ........................................................... 38
INSPECTION AFTER REMOVAL ........................ 41
INSTALLATION .................................................... 42
CAMSHAFT ............................................................... 47
Components ........................................................... 47
Removal and Installation ........................................ 47
REMOVAL ........................................................... 47
INSPECTION AFTER REMOVAL ........................ 49
INSTALLATION .................................................... 51
INSPECTION AFTER INSTALLATION ................ 54
Valve Clearance ...................................................... 55
INSPECTION ....................................................... 55
ADJUSTMENT .................................................... 57
OIL SEAL .................................................................. 59
Removal and Installation of Valve Oil Seal ............. 59
REMOVAL ........................................................... 59
INSTALLATION .................................................... 59
Removal and Installation of Front Oil Seal ............. 60
REMOVAL ........................................................... 60
INSTALLATION .................................................... 60
Removal and Installation of Rear Oil Seal .............. 61
REMOVAL ........................................................... 61
INSTALLATION .................................................... 61
CYLINDER HEAD ..................................................... 62
On-Vehicle Service ................................................. 62
CHECKING COMPRESSION PRESSURE ......... 62
Components ........................................................... 63
Removal and Installation ........................................ 63
REMOVAL ........................................................... 63
INSPECTION AFTER REMOVAL ........................ 64
INSTALLATION .................................................... 65
Components ........................................................... 66
Disassembly and Assembly .................................... 66
DISASSEMBLY ................................................... 66
ASSEMBLY ......................................................... 67
Inspection After Disassembly ................................. 68
VALVE DIMENSIONS .......................................... 68
VALVE GUIDE CLEARANCE .............................. 68
VALVE GUIDE REPLACEMENT ......................... 69
VALVE SEAT CONTACT ..................................... 70
VALVE SEAT REPLACEMENT ........................... 70
VALVE SPRING SQUARENESS ......................... 71
VALVE SPRING DIMENSIONS AND VALVE
SPRING PRESSURE LOAD ............................... 72
ENGINE ASSEMBLY ................................................ 73
Components ........................................................... 73
Removal and Installation ........................................ 73
REMOVAL ........................................................... 74
INSTALLATION .................................................... 76
INSPECTION AFTER INSTALLATION ................ 76
CYLINDER BLOCK ................................................... 77
Components ........................................................... 77
Disassembly and Assembly .................................... 78
DISASSEMBLY ................................................... 78ASSEMBLY ..........................................................81
How to Select Piston and Bearing ..........................87
DESCRIPTION ....................................................87
HOW TO SELECT PISTON .................................87
HOW TO SELECT CONNECTING ROD BEAR-
ING .......................................................................88
HOW TO SELECT MAIN BEARING ....................91
Inspection After Disassembly ..................................95
CRANKSHAFT END PLAY ..................................95
CONNECTING ROD SIDE CLEARANCE ...........95
PISTON TO PISTON PIN OIL CLEARANCE .......95
PISTON RING SIDE CLEARANCE .....................96
PISTON RING END GAP ....................................96
CONNECTING ROD BEND AND TORSION .......97
CONNECTING ROD BIG END DIAMETER ........97
CONNECTING ROD BUSHING OIL CLEAR-
ANCE ...................................................................97
CYLINDER BLOCK TOP SURFACE DISTOR-
TION ....................................................................98
MAIN BEARING HOUSING INNER DIAMETER ...98
PISTON TO CYLINDER BORE CLEARANCE ....99
CRANKSHAFT MAIN JOURNAL DIAMETER ... 100
CRANKSHAFT PIN JOURNAL DIAMETER ...... 100
OUT-OF-ROUND AND TAPER OF CRANK-
SHAFT ............................................................... 100
CRANKSHAFT RUNOUT .................................. 100
CONNECTING ROD BEARING OIL CLEAR-
ANCE ................................................................. 101
MAIN BEARING OIL CLEARANCE ................... 101
MAIN BEARING CRUSH HEIGHT .................... 102
CONNECTING ROD BEARING CRUSH
HEIGHT ............................................................. 102
MAIN BEARING CAP BOLT OUTER DIAMETER . 103
CONNECTING ROD BOLT OUTER DIAMETER . 103
CLOGGED OR DAMAGED OIL FILTER (FOR
INTAKE VALVE TIMING CONTROL) ................. 103
FLYWHEEL DEFLECTION (M/T MODELS) ...... 103
MOVEMENT AMOUNT OF FLYWHEEL (M/T
MODELS) ........................................................... 103
SERVICE DATA AND SPECIFICATIONS (SDS) .... 105
Standard and Limit ................................................ 105
GENERAL SPECIFICATIONS ........................... 105
DRIVE BELT ...................................................... 105
WATER CONTROL VALVE ................................ 105
EXHAUST MANIFOLD ...................................... 105
THERMOSTAT ................................................... 105
SPARK PLUG .................................................... 105
CYLINDER HEAD .............................................. 105
VALVE ................................................................ 106
CAMSHAFT AND CAMSHAFT BEARING ......... 109
CYLINDER BLOCK ............................................110
PISTON, PISTON RING AND PISTON PIN ...... 111
CONNECTING ROD ..........................................112
CRANKSHAFT ...................................................112
MAIN BEARING .................................................114
CONNECTING ROD BEARING .........................114

CAMSHAFT
EM-49
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: June 20062007 Versa
12. Remove camshafts.
13. Remove valve lifters.
NOTE:
Identify installed positions, and store them without mixing them up.
INSPECTION AFTER REMOVAL
Camshaft Runout
1. Put V-block on a precise flat table, and support No. 2 and 5 jour-
nal of camshaft.
CAUTION:
Never support No. 1 journal (on the side of camshaft
sprocket) because it has a different diameter from the other
four locations.
2. Set dial indicator (A) vertically to No. 3 journal.
3. Turn camshaft to one direction with hands, and measure the
camshaft runout on dial indicator. (Total indicator reading)
4. If it exceeds the limit, replace camshaft.
Camshaft Cam Height
1. Measure the camshaft cam height with a micrometer (A).
2. If it exceeds the limit, replace camshaft.
Camshaft Journal Oil Clearance
CAMSHAFT JOURNAL OUTER DIAMETER
Measure the outer diameter of camshaft journal with a micrometer
(A).
CAMSHAFT BRACKET INNER DIAMETER

Tighten camshaft bracket bolts with specified torque. Refer to EM-51, "INSTALLATION" for the tightening
procedure.Standard : Less than 0.02 mm (0.0008 in).
Limit : 0.05 mm (0.0020 in)
PBIC3177J
Standard:
Intake : 44.605 - 44.795 mm (1.7560 - 1.7635 in)
Exhaust : 43.175 - 43.365 mm (1.6997 - 1.7072 in)
Limit:
Intake : 44.405 mm (1.7482 in)
Exhaust : 42.975 mm (1.6919 in)
PBIC3178J
Standard:
No. 1 : 27.935 - 27.955 mm (1.0998 - 1.1006 in)
No. 2, 3, 4, 5 : 24.950 - 24.970 mm (0.9823 - 0.9831 in)
PBIC3179J

OIL SEAL
EM-59
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: June 20062007 Versa
OIL SEALPFP:12279
Removal and Installation of Valve Oil SealEBS00T6H
REMOVAL
1. Remove camshafts. Refer to EM-47, "Components" .
2. Remove valve lifters. Refer to EM-47, "
CAMSHAFT" .
3. Rotate crankshaft, and set piston whose valve oil seal is to be removed to TDC. This will prevent valve
from dropping into cylinder.
CAUTION:
When rotating crankshaft, be careful to avoid scarring front cover with timing chain.
4. Remove valve collet.

Compress valve spring using Tool, the attachment and the
adapter (A). Remove valve collet with a suitable magnet hand
(B).
CAUTION:
When working, be careful not to damage valve lifter holes.
5. Remove valve spring retainer, valve spring and valve spring seat.
6. Remove valve oil seal using Tool (A).
INSTALLATION
1. Apply new engine oil to valve oil seal joint surface and seal lip.
2. Press in valve oil seal to the height “H” shown using Tool (A).
3. Installation of the remaining components is in the reverse order of removal.Tool number : KV101092S0 (J-26336-B)
PBIC3727E
Tool number :KV10107902 (J-38959)
PBIC3728E
Height “H” : 15.1 - 15.7 mm (0.594 - 0.618 in)
Tool number : KV10115600 ( — )
PBIC3 211 J

CYLINDER HEAD
EM-67
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: June 20062007 Versa

Compress valve spring using Tool, attachment and adapter
(A). Remove valve collet using a suitable magnet hand.
CAUTION:
When working, be careful not to damage valve lifter holes.
4. Remove valve spring retainer and valve spring (with valve spring seat).
CAUTION:
Never remove valve spring seat from valve spring.
5. Push valve stem to combustion chamber side, and remove valve.
NOTE:
Identify installed positions, and store them without mixing them up.
6. Remove valve oil seal using Tool (A).
7. When valve seat must be replaced, refer to EM-70, "
VALVE SEAT REPLACEMENT" to removal.
8. When valve guide must be replaced, refer to EM-69, "
VALVE GUIDE REPLACEMENT" to removal.
ASSEMBLY
1. Install valve guide if removed. Refer to EM-69, "VALVE GUIDE REPLACEMENT" .
2. Install valve seat if removed. Refer to EM-70, "
VALVE SEAT REPLACEMENT" .
3. Install valve oil seal.

Install with a valve oil seal using Tool (A) to match dimension
as shown.
NOTE:
Dimension “H” is height that measured before installing valve
spring (with valve spring seat).
4. Install valve.

Install larger diameter to intake side.Tool number : KV101092S0 (J-26336-B)
PBIC3209J
Tool number : KV10107902 (J-38959)
PBIC3210J
Tool number : KV10115600 (J-38958)
Height “H” : 15.1 - 15.7 mm (0.594 - 0.618 in)
PBIC3 211 J

EM-72Revision: June 2006
CYLINDER HEAD
2007 Versa
VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD

Check valve spring pressure with valve spring seat installed at
the specified spring height.
CAUTION:
Never remove valve spring seat from valve spring.
Standard:

If the installation load or load with valve open is out of the standard, replace valve spring (with valve spring
seat).
SEM 113
Items Intake Exhaust
Free height 44.90 - 45.10 mm (1.7677 - 1.7755 in) 45.74 - 45.94 mm (1.8007 - 1.8086 in)
Installation height 35.30 mm (1.390 in) 35.30 mm (1.390 in)
Installation load 153 - 173 N (15.6 - 17.6 kg, 34 - 39 lb) 139 - 157 N (14.2 - 16 kg, 10 - 35 lb)
Height during valve open 26.36 mm (1.0377 in) 27.80 mm (1.0944 in)
Load with valve open 335 - 377 N (34.2 - 38.5 kg, 75 - 85 lb) 266 - 297 N (27.1 - 3.03 kg, 60 - 67 lb)
Identification color White Orange

EM-102Revision: June 2006
CYLINDER BLOCK
2007 Versa

If clearance exceeds the limit, select proper main bearing according to main bearing inner diameter and
crankshaft main journal diameter to obtain specified bearing oil clearance. Refer to EM-91, "
HOW TO
SELECT MAIN BEARING" .
Method of Using Plastigage

Remove engine oil and dust on crankshaft main journal and the surfaces of each bearing completely.

Cut a plastigage slightly shorter than the bearing width, and place it in crankshaft axial direction, avoiding
oil holes.

Install main bearings to cylinder block and main bearing cap, and tighten main bearing cap bolts to the
specified torque. Refer to EM-81, "
ASSEMBLY" for the tightening procedure.
CAUTION:
Never rotate crankshaft.

Remove main bearing cap and bearings, and using the scale (A)
on the plastigage bag, measure the plastigage width.
NOTE:
The procedure when the measured value exceeds the limit is
same as that described in the “Method by Calculation”.
MAIN BEARING CRUSH HEIGHT

When main bearing cap is removed after being tightened to the
specified torque with main bearings (1) installed, the tip end of
bearing must protrude (B). Refer to EM-81, "
ASSEMBLY" for
the tightening procedure.

If the standard is not met, replace main bearings.
CONNECTING ROD BEARING CRUSH HEIGHT

When connecting rod bearing cap is removed after being tight-
ened to the specified torque with connecting rod bearings (1)
installed, the tip end of bearing must protrude. Refer to EM-81,
"ASSEMBLY" for the tightening procedure (B).

If the standard is not met, replace connecting rod bearings.: 0.012 - 0.022 mm (0.0005 - 0.0009 in)
Limit : 0.065 mm (0.0026 in)
PBIC3278J
A : Example
Standard : There must be crush height.
PBIC3279J
A : Example
Standard : There must be crush height.
PBIC3279J

EM-106Revision: June 2006
SERVICE DATA AND SPECIFICATIONS (SDS)
2007 Versa
VA LV E
Va lv e Tim in g
Unit: degree
( ): Valve timing control “ON”
Valve Dimensions
Unit: mm (in) Normal cylinder head height “H” 130.9 (5.15) — Items Standard Limit
PBIC0924E
Va l v e t i m i n g
ab c de f
212 224 -8 (32) 52 (12) 7 25
PBIC4542E
Valve head diameter “D”Intake 33.8 - 34.1 (1.331 - 1.343)
Exhaust 27.6 - 27.9 (1.087 - 1.098)
Valve length “L”Intake 106.21 (4.181)
Exhaust 105.26 (4.144)
Valve stem diameter “d”Intake 5.465 - 5.480 (0.2152 - 0.2157)
Exhaust 5.455 - 5.470 (0.2148 - 0.2154)
Valve seat angle “α”45°15′ - 45°45′
Valve margin “T”Intake 1.1 (0.043)
Exhaust 1.2 (0.047)
SEM 18 8A