2006 MERCEDES-BENZ SPRINTER check engine

Symptom List:
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P1630-IMMOBILIZER
P2201-IMMOBILIZER CAN MESSAGE ERROR
P2243-NO MESSAGE RECEIVED FROM SKREEM
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1630-IMMOBILIZER.
POSSIBLE CAUSES
CHECKING SKREEM DTC'S
OPEN CAN BUS CIRCUITS
SKREEM MODULE
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off for 10 seconds.
Turn the ignition on.
Monitor the DRB for ECM DTCs.
Did this DTC set again?All
Ye s!Go To 2
No!Go To 4
2 Turn the ignition on.
With the DRBIIIt, attempt to communicate with the SKREEM and read SKREEM
DTCs.
NOTE: If the DRB is unable to communicate with the SKREEM, refer to the
appropriate test in the Communication category
Are there any SKREEM DTC's?All
Ye s!Repair SKREEM DTC's as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No!Go To 3
102
DRIVEABILITY - DIESEL

Symptom List:
P1681-ACM CIRCUIT FAULT
P1681-ACM CIRCUIT SHORT TO VOLTAGE
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P1681-ACM CIRCUIT FAULT.
POSSIBLE CAUSES
AIRBAG CONTROL MODULE
INTERMITTENT CONDITION
ACM SIGNAL CIRCUIT SHORTED TO VOLTAGE
ENGINE CONTROL MODULE
TEST ACTION APPLICABILITY
1NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
With the DRB, check the Airbag Module for proper communication and DTCs. If
there are any ACM DTCs, repair them prior to continuing this test.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Start the engine.
With the DRB, read ECM DTCs.
Did this DTC set again?All
Ye s!Go To 2
No!Go To 4
2 Turn the ignition off.
Disconnect the ECM harness connectors.
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Turn the ignition on.
Measure the voltage of the ACM Signal circuit.
Is the voltage below 1.0 volt?All
Ye s!Replace the Engine Control Module in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
No!Go To 3
104
DRIVEABILITY - DIESEL

Symptom List:
P2009-WATER IN FUEL SENSOR - WATER IN FUEL
P2009-WATER IN FUEL SENSOR SIGNAL ERROR
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2009-WATER IN FUEL SENSOR
- WATER IN FUEL.
POSSIBLE CAUSES
12-VOLT SUPPLY CIRCUIT OPEN
CHECKING ECM POWER AND GROUNDS
CHECKING THE ENGINE CONTROL RELAY SYSTEM
ECM - WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
ECM - WATER IN FUEL SENSOR SIGNAL SHORT TO GROUND
SENSOR GROUND CIRCUIT OPEN
WATER IN FUEL SENSOR FAILURE
WATER IN FUEL SENSOR SIGNAL CIRCUIT OPEN
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO 12-VOLT SUPPLY
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND
WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose
DTCs P1611, P2306 or P2332 before diagnosing this DTC.
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
NOTE: If you are here due to a P2009 indicating(Water In The Fuel Filter(
DTC, ensure that the fuel system is not contaminated with water or other
fluids before continuing.
NOTE: If the fuel system is contaminated, refer to the Service Information
to remove fuel, clean system and refill with known good fuel.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Start the engine several times, letting the engine run for at least 30 seconds at a
time.
With the DRB, read ECM DTCs.
Did this DTC set again?All
Ye s!Go To 2
No!Go To 11
106
DRIVEABILITY - DIESEL

TEST ACTION APPLICABILITY
2 Turn the ignition off.
Disconnect the ECM harness connectors.
Connect a jumper wire between ground and the Engine Control Relay Control circuit
in ECM C2 harness connector cavity 44.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Fused Engine Control Relay
Output circuits at the ECM C2 harness connector cavities 1, 3 and 5.
Choose the appropriate result.All
Test light is on for all circuits.
Go To 3
Test light is on for 1 or 2 circuits
Repair the Engine Control Relay Output circuit(s) that did not
illuminate brightly for an open.
Perform ROAD TEST VERIFICATION - VER-2.
Light off for all circuits.
Refer to symptom Checking the ECM Power and Grounds.
Perform ROAD TEST VERIFICATION - VER-2.
3 Turn the ignition off.
Disconnect the Water In Fuel Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Water In Fuel Sensor Signal circuit.
Select the appropriate voltage reading.All
Voltage is above 5.4 volts.
Go To 4
Voltage is between 4.7 and 5.4 volts.
Go To 6
Voltage is below 4.7 volts.
Go To 8
4 Turn the ignition off.
Disconnect the In Fuel Level Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Turn the ignition on.
Measure the voltage of the Water In Fuel Sensor Signal circuit.
Is the voltage below 1.0 volt?All
Ye s!Go To 5
No!Repair the Water In Fuel Sensor Signal circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.
107
DRIVEABILITY - DIESEL
P2009-WATER IN FUEL SENSOR - WATER IN FUEL ÐContinued

TEST ACTION APPLICABILITY
1NOTE: Inspect the turbocharger inlet tube between the MAF Sensor and the
turbocharger for damage, restriction or poor connection. Any of these
conditions can cause a MAF Plausibility DTC.
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
Turn the ignition on.
With the DRBIIIt, erase the ECM DTCs.
Test drive the vehicle.
With the DRBIIIt, read the ECM DTCs.
Does the DRB III display a Mass Air Flow Sensor DTC?All
Ye s!Replace the MAF Sensor.
Perform ROAD TEST VERIFICATION - VER-2.
No!Go To 2
2WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running and at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?All
Ye s!Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No!Test Complete.
111
DRIVEABILITY - DIESEL
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION ÐContinued

TEST ACTION APPLICABILITY
1NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose
DTCs P1611, P2306 or P2332 before diagnosing this DTC.
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
NOTE: The engine oil must be at the proper level for this test to be valid.
Refer to the Service Information and ensure the engine oil level is at the
specified level.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Start the engine several times, letting the engine run for at least 30 seconds at a
time.
With the DRB, read ECM DTCs.
Did this DTC set again?All
Ye s!Go To 2
No!Go To 10
2WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Refer to any Technical Service Bulletins (TSB) that may apply.
Turn the ignition off.
NOTE: This DTC implies that the engine may be contaminated by water,
engine coolant or other material due to a mechanical or service failures
such as failed gaskets, seals, cracks or incorrectly installed components.
Inspect the engine for conditions referred to in the above note.
Were any of the above conditions present?All
Ye s!Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No!Go To 3
3 Turn the ignition off.
Disconnect the Engine Oil Sensor harness connector.
Turn the ignition on.
Measure the voltage of the Engine Oil Sensor Signal circuit.
Select the appropriate voltage reading.All
Voltage is above 5.4 volts.
Go To 4
Voltage is between 4.7 and 5.4 volts.
Go To 5
Voltage is below 4.7 volts.
Go To 7
11 4
DRIVEABILITY - DIESEL
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY Ð
Continued

Symptom List:
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL
FLOW EXCEEDED
P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION
ERROR
P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BE-
LOW MINIMUM QUANTITY
P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS
TOO LOW
P2018-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS
TOO HIGH
P2019-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL
PRESSURE EXCEEDED
P2019-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS
TOO LOW
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS
TOO LOW
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE
TOO HIGH
P2021-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE
TOO LOW
P2023-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE
TOO HIGH
P2047-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL
PRESSURE EXCEEDED
P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION
ERROR
P2051-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL
PRESSURE EXCEEDED
P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY
WITH FUEL PRESSURE SOLENOID
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2015-FUEL RAIL PRESSURE
MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED.
POSSIBLE CAUSES
AIR IN FUEL SYSTEM
CHECKING ELECTRICAL CIRCUITS-ENGINE RUNNING
CHECKING ELECTRICAL CIRCUITS-NO START
CHECKING FOR OTHER DTC'S
CHECKING THE FUEL DELIVERY SYSTEM
11 7
DRIVEABILITY - DIESEL

POSSIBLE CAUSES
CHECKING THE FUEL DELIVERY SYSTEM
CORRECTION QUANTITY CHECK
CYLINDER SPEED CHECK
FUEL INJECTION PUMP CHECK
FUEL LEAK QUANTITY CHECK
FUEL LEAK QUANTITY CHECK
FUEL PRESSURE SOLENOID
FUEL PRESSURE SOLENOID CHECK
FUEL PRESSURE VARIATION CHECK
FUEL PUMP
FUEL QUANTITY SOLENOID
FUEL SYSTEM CONTAMINATION
FUEL SYSTEM LEAK
INTERMITTENT CONDITION
TEST ACTION APPLICABILITY
1WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UN-
DER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL
INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE
EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL
LEAKS.
WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENE-
TRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR
HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR
SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN
SERVICING FUEL SYSTEM.
Turn the ignition on.
With the DRBIIIt, read the ECM DTCs.
Are there any other DTCs present?All
Ye s!Refer to symptom list for problems related to the DTC other than
this DTC.
Perform ROAD TEST VERIFICATION - VER-2.
No!Go To 2
2 Turn the ignition on.
With the DRBIIIt, erase the ECM DTCs.
Attempt to start the engine.
Does the engine start and idle?All
Ye s!Go To 3
No!Go To 17
11 8
DRIVEABILITY - DIESEL
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW
EXCEEDED Ð
Continued