2006 Lexus GS430 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2006 PROD. OWNER'S MANUAL (OM30786U)

CHASSIS
545
– BRAKES
Pedal clearance *
165 mm (2.6 in.) Min.
Pedal free play1.0 − 2.0 mm (0.04 − 0.08 in.)
Brake pad wear limit1.0 mm (0.04 in.)
Parking brake lining wear limit1.0 mm (0.04 in.)
Parking brake adjustment *25 − 7 clicks
Fluid typeSAE J1703 or FMVSS No. 116 DOT 3
*1Minimum pedal clearance when depressed with the force of 490 N (50 kgf,\
110 lbf.) with the engine running
*
2Parking brake adjustment when depressed with the force of 300 N (30.6 k\
gf, 67.4lbf.)
– STEERING
Free play
Less than 30 mm (1.2 in.)

CHASSIS
546
– TIRES AND WHEELS
Front and rear:Tire size
225/50R17 94W or P225/50R17 93V
Tire inflation pressure
Recommended cold tire inflation pressure
Front 230 kPa (2.3 kgf/cm2 or bar, 33 psi)
Rear 230 kPa (2.3 kgf/cm2 or bar, 33 psi)
For sustained high speeds above 160 km/h (100 mph), in
countries where such speeds are permitted by law, add 50 kPa
(0.5 kgf/cm
2 or bar, 7 psi) to the front tires and rear tires, but
never exceed the maximum cold tire inflation pressure molded
on the tire sidewall.
Wheel size17 x 7 1/2 JJ
Wheel nut torque103 N·m (10.5 kgf·m, 76 ft·lbf.)
Spare (Vehicles with standard tires only):
Tire size
T155/70D17 110M
Tire inflation pressure420 kPa (4.3 kgf/cm2, 4.2 bar, 60 psi)
Wheel size17 x 4T
Wheel nut torque103 N·m (10.5 kgf·m, 76 ft·lbf.)
NOTE:
For complete information on tires (e.g. replacing tires or replacing wh\
eels), see “Checking tire inflation pressure”
through “Aluminum wheel precautions” on page 548 through 570.

CHASSIS
547
CHECKING BRAKE FLUID
G62010
GS430
G62011
GS300
To check the fluid level, simply look at the seethrough
reservoir. The level should be between the ”MAX” and
”MIN” lines on the tank. It is normal for the brake fluid level to go down slightly as the
brake pads wear or when the fluid level in the accumulator is
high.
If the level is low, take your vehicle to a Lexus dealer as
soon as possible. Do not drive your vehicle if the brake
system warning light (red) is on. Call a Lexus dealer for
assistance.
If the fluid level goes down soon after your vehicle is
serviced, it may indicate a serious mechanical problem.
Have your vehicle checked by your Lexus dealer.
CAUTION
Brake
fluid can harm your hands or eyes. If fluid gets on
your hands or in your eyes, flush the affected area with
clean water immediately. If you still feel uncomfortable
with your hands or eyes, go to the doctor.
NOTICE
If brake fluid is spilled on the vehicle, be sure to wipe it
off to prevent damage to parts or paint.

CHASSIS
548
CHECKING TIRE INFLATIONPRESSURE
G63015
The recommended cold tire inflation pressure, tire
size and the combined weight of occupants and
cargo (vehicle capacity weight) are described on the
tire and loading information label.
You should check the tire inflation pressure every two
weeks, or at least once a month. And do not forget the
spare! The inflation pressure for the spare tire should be
420 kPa (4.3 kgf/cm
2, 4.2 bar, 60 psi).
The following instructions for checking tire inflation
pressure should be observed:
 The pressure should be checked only when the
tires are cold. If your vehicle has been parked for at
least 3 hours and has not been driven for more than
1.5 km or 1 mile since, you will get an accurate cold
tire inflation pressure reading.
 Always use a tire pressure gauge. The appearance
of the tire can be misleading. Besides, tire inflation
pressures that are even just a few pounds off can
degrade ride and handling.
 Do not bleed or reduce tire inflation pressure after
driving. It is normal for the tire inflation pressure to
be higher after driving.
 Never exceed the vehicle capacity weight.
Passengers and luggage weight should be located so
that the vehicle is balanced.

CHASSIS
549
Inspection and adjustment procedure
G63001
 1Tire valve
2Tire pressure gauge
1. Remove the tire valve cap.
2. Press the tip of the tire pressure gauge to the tire
valve.
3. Read the pressure using the graduations of the
gauge.
4. In case the tire inflation pressure is not within the
prescribed range, insert the compressed air from the
valve. In case of applying too much air, press the center
of the valve and release the air to adjust.
5. After completing the tire inflation pressure
measurement and adjustment, apply soapy water to the
valve and check for leakage. 6. Install the tire valve cap.
If a gauge and air pump are not available, have your
vehicle checked by your Lexus dealer.
CAUTION
Be sure to reinstall the tire valve caps. W
ithout the
valve caps, dirt or moisture could get into the
valve core and cause air leakage. If the caps have
been lost, have new ones put on as soon as
possible.
Incorrect tire inflation pressure may waste fuel, reduce
the comfort of driving, reduce tire life and make your
vehicle less safe to drive.
If a tire needs frequent refilling, have it checked by your
Lexus dealer.

CHASSIS
550
CAUTION
Keep your tires properly inflated. Otherwise, the
following conditions may occur and cause an
accident resulting in death or serious injuries.
Low tire pressure (underinflation):
Excessive wear
 Uneven wear
 Poor handling
 Possibility of blo wouts from an overheated tire
 Poor sealing of the tire bead
 Wheel deformation and/or tire separation
 A greater possibility of tire damage from road
hazards
High tire pressure (overinflation):
 Poor handling
 Excessive wear
 Uneven wear
 A greater possibility of tire damage from road
hazards

CHASSIS
551
TIRE INFORMATION
Tire symbols (Standard and runflat tire)
G63006
The illustration indicates typical tire symbols.

CHASSIS
552
1 Tire size: For details, see “Tire size” on page
555.
2 DOT and Tire Identification Number (TIN): For
details, see “DOT and Tire Identification Number
(TIN)” on page 555.
3 Tire ply composition and materials : Plies
mean a layer of rubber −coated parallel cords.
Cords mean the strands forming the plies in the
tire.
4 Load limit at maximum cold tire inflation
pressure: For details, see “Checking and
replacing tires” on page 563.
5 Uniform tire quality grading For details, see
“Uniform tire quality grading” on page 557.
6 Maximum cold tire inflation pressure: This
means the pressure to which a tire may be
inflated. For recommended cold tire inflation
pressure, see “Specifications” on page 546.
7 “TUBELESS” or “TUBE TYPE”: A tubeless tire
does not have a tube inside the tire and air is
directly filled in the tire. A tube type tire has a
tube inside the tire and the tube maintains the air
pressure.
8 Radial tires or biasply tires : A radial tire has
“RADIAL” on the sidewall. A tire not marked with
“RADIAL” is a bias −ply tire.
9 Runflat tire (RFT) or standard tire: This
vehicle can be equipped with either run −flat tires
(RFT) or standard tires. A “RFT” or “DSST” mark
is molded on the sidewall of the run −flat tire. For
details, see “Run −flat tires” on page 561.
10 Location of tread wear indicators: For details,
see “Checking and replacing tires” on page 563.
11 Summer tire or all season tire: An all season
tire has “M+S” on the sidewall. The tire not
marked with “M+S” is a summer tire. For details,
see “Types of tires” on page 562.