2006 INFINITI QX56 key

BL-102
AUTOMATIC BACK DOOR SYSTEM
Revision: November 20092006 QX56
Back Door Close Switch Operation (Fully Open → Fully Closed Operation)

When the back door close switch is pressed, the back door control unit terminal 8 receives the signal.

The back door control units checks back door close switch terminal 13 status and door position (must be
fully opened), through rotary encoder and battery voltage.

When the back door control unit receives the signal, if the auto back door operating enable conditions are
met, it sends a signal through terminal 6 and grounds terminal 9 to sound the warning chime and sends a
signal to the BCM through terminal 4 to flash the hazard lamps.

The back door control unit supplies power to the magnetic clutch and the back door motor and move the
back door in the close direction. (At this time, it also executes speed control, input reverse, and anti-pinch
detection control.)

When the back door reaches the half-latch state, the half-latch switch detects this and the signal is sent to
the back door control unit terminal 22.

When the back door control unit receives the half latch switch signal, it switches OFF the back door motor
and the magnetic clutch and operates the cinch latch motor.

When the back door latch operates and full close is detected through terminal 14 of the back door control
unit, the cinch latch motor reverses to the neutral position and the back door auto closure operation ends
and the door is fully closed.
Reversal
The door will reverse direction during power open or close operation if the automatic door main switch, keyfob
or back door close switch is operated. A chime will sound to announce the reversal.
Anti-Pinch Function

During auto operation, if an object is detected in the door's path, a warning chime sounds and the back
door operates in the reverse direction to prevent pinching.

During auto close operation, if an object is detected by the pinch strips in the door's path, a warning chime
sounds and the back door operates in the open direction until it is fully open.
Gas Stay Check

During each power open operation, the back door control unit monitors motor current draw to determine if
the gas stays are functioning properly.

If a malfunction of the gas stays is detected, the back door control unit will close the back door while
sounding the warning chime. The back door cannot be opened using the switches until the gas stay mal-
function is repaired.
Warning Functions

The hazard warning lamps flash and a warning chime is sounded according to the back door operating
state, operations, and conditions.

AUTOMATIC BACK DOOR SYSTEMBL-103
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
Auto Back Door Operation Enable Conditions
Control When Operating Enable Conditions Not Met During Power Open/Close
Control When Operating Enable Conditions No Longer Met
Operation Power liftgate switchRemote keyless entry Back door handle switch Back door
close switch
Operating direction Fully closed
→
open Fully open
→
closed Fully closed
→
open Fully open
→ closed Fully closed
→
open Fully open
→
closed Fully open
→
closed
Close
switch CANCEL or NEUTRAL
NEUTRALNEUTRAL
Vehicle stop
condition A/T selector
lever in P or N
range and vehi-
cle speed less
than 2 km/h or ignition switch
in OFF position —A/T selector
lever in P or N
range and vehi-
cle speed less
than 2 km/h or ignition switch
in OFF position —A/T selector
lever in P or N
range and vehi-
cle speed less
than 2 km/h or ignition switch
in OFF position ——
Battery volt-
age Approx. 11V or more
Back door
lock status ————
Unlocked——
Glass hatch Closed
ItemsOperation condition Not met caseControl
A/T selector lever P position P or N position with ignition ON
or any position with ignition
OFFOther
Continue power open or close,
but sounds warning chime.
Back door close switch NEUTRAL CANCEL
Cancels power open/close
operation or door will release to
manual mode.
Voltage drop
11V or more11 > V > 9
9 > V > reset voltage
reset voltage > V
No power function available
Handle switch Normal (GND)Error (OPEN) No operation. Cancel power
open/close release to manual.
Glass hatch ClosedOFF Cancels power door open oper-
ation, door will release to man-
ual mode.
Description
Operation Control
Back door close switch turned to CANCEL Warning chime active
→
Shift to manual mode after full open or
close operation is complete
(Recovery to power mode when main
switch turned OFF or door fully closed) →
Shift to manual mode
A/T selector lever P or N position with igni-
tion switch ON Warning chime active and one-way opera-
tion continuous
(Warning chime inactive and door fully
open or fully closed or operating conditions
recovered)Full open: power close operation allowed
Full close: operating conditions not met
→
no power open function.
Voltage drop 11 - 9V One-way operation continued (equivalent
to the case of starting voltage
← 11 V f o r
handle operation with warning chime
active) Not allowed
Voltage drop less than 9V
(Microcomputer reset voltage - clutch hold
voltage)

Motor stopped

Clutch may slip

Control not possible because microcom-
puter being reset Control not possible because microcom-
puter being reset

BL-104
AUTOMATIC BACK DOOR SYSTEM
Revision: November 20092006 QX56
Warning Chime Active Conditions
The warning chime uses two types of audio warnings, a friendly chime and a warning chime. The friendly
chime consists of dings lasting 0.66 seconds each immediately followed by the next ding. The warning chime
consists of beeps lasting 0.33 seconds with a pause of 0.33 seconds between each beep.
Reverse Conditions
Operation statusOperation or conditions Warning chime pattern
When auto operation starts Power liftgate switch operation
Friendly chime
2 seconds, 3 dings
Remote keyless entry operation
Back door handle switch operation
Back door close switch operation
When reverse operation starts When reverse request is detected from
power liftgate switch, remote keyless
entry or back door close switch
Friendly chime
1.3 seconds, 2 dings
When obstacle is detected Warning chime
2 seconds, 3 beeps
Operating at low voltage While opening or closing Warning chime
2 seconds, 3 beeps
A/T selector lever not in P position Back door close operation
Friendly chime
Continuously dings
Back door open operation Warning chime
Continuously beeps
(until close operation is started)
Type Overload reverse
Operation covered Both directions
Detection method Operation speed and motor current change direction
Pinch strips during back door close operation
Non-reversed area

For about 0.5 seconds immediately after drive motor operation
starts

Between full open and approx. 7 ° from full open

Closure operation area (half switch - close switch)
Number of times reverse allowed One reversal is allowed (if a second obstacle is detected during a
power open or close operation, the door reverts to manual
mode).

AUTOMATIC BACK DOOR SYSTEMBL-113
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
Trouble Diagnosis ProcedureEIS00612
1. Check the trouble symptom and customer's requests.
2. Understand outline of system. Refer to BL-45, "
System Description" .
3. Confirm system operation.
4. Perform self-diagnosis procedures. Refer to BL-113, "
Self-Diagnosis Procedures" .
5. Refer to diagnosis chart by symptom, repair or replace any malfunctioning parts. Refer to BL-114, "
Diag-
nosis Chart" .
6. Inspection End.
Self-Diagnosis ProceduresEIS00613
INPUT SIGNAL CHECK MODE
Input signal check mode allows testing of switch input signal to the back door control unit.
To activate input signal check mode on the automatic back door, perform the following steps:
1. Turn ignition switch OFF.
2. Turn back door close switch to CANCEL (system cancelled).
3. Place A/T selector lever in P position.
4. Using the inside emergency release lever, open the back door.
5. Have an assistant press and hold the back door handle switch.
6. While the assistant continues to hold the back door handle switch, turn ignition switch ON (DO NOT start engine).
7. After approximately 5 seconds, the back door warning chime will sound for 0.5 seconds.
8. Release the back door handle switch.
9. Within 8 seconds of the back door warning chime sounding, press and hold the power liftgate switch.
10. After approximately 5 seconds, the back door warning chime will sound for 1 second.
11. Release the power liftgate switch.
12. The input signal check mode is now initialized.
The input signal check mode can test the following inputs. The back door warning chime will sound for approx-
imately 0.5 seconds each time a switch signal input occurs. Use this test when one of these inputs is not
responding during normal automatic back door operation.
*Back door warning chime should sound as soon as vehicle moves.
Turn ignition switch OFF to end input signal check mode.
OPERATING CHECK MODE
Operating check mode allows self-diagnosis of the automatic back door system.
To activate operating check mode on the automatic back door, perform the following steps:
1. Turn ignition switch OFF.
2. Turn back door close switch to CANCEL (system cancelled).
3. Place A/T selector lever in P position.
Switch signal OperationRefer to
Power liftgate switch OFF → ON BL-116
Back door close switch (CLOSE) OFF → ON BL-118
Back door close switch (CANCEL) OFF → ON BL-119
Back door handle switch OFF → ON BL-125
Glass switch OFF → ON BL-117
A/T device (park switch) P position → other than P position AT- 6 1
Vehicle speed* Vehicle speed—
Remote keyless entry signal Keyfob switch OFF → ON BL-44
Door lock/unlock signal LOCK → UNLOCK BL-16
Pinch strip LH signal OFF → ON BL-121
Pinch strip RH signal OFF → ON BL-121

AUTOMATIC BACK DOOR SYSTEMBL-115
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
Back Door Power Supply and Ground Circuit InspectionEIS00615
1. BACK DOOR POWER SUPPLY CIRCUIT INSPECTION
1. Turn ignition switch OFF.
2. Disconnect back door control unit.
3. Check voltage between back door control unit connector B55 terminals 3, 10 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. BACK DOOR GROUND CIRCUIT INSPECTION
Check continuity between back door control unit connector B55 ter-
minal 1, 2 and ground.
OK or NG
OK >> Circuit is OK.
NG >> Repair or replace harness.
During auto closing operations, if obstruction is detected, the
door does not operate in reverse. Back door motor assembly
—
During close or cinch operations, the door does not operate in
reverse if the back door handle is operated. Handle switch system
BL-125
When the keyfob is operated, the back door does not operate
automatically. Remote keyless entry system inspection
BL-44Power window serial linkBL-112
Pinch strip system inspectionBL-121
Auto closure does not operate. Half-latch switch system
BL-122Cinch latch motor systemBL-126
Handle switch systemBL-125
The back door does not open.
(Closure motor rotation is not reversed.) Open switch system
BL-123
Handle switch systemBL-125
Warning chime does not sound. Back door warning chime systemBL-122
Auto closure operation works, but the back door is not fully
closed Close switch system
BL-124Handle switch systemBL-125
Cinch latch motor systemBL-126
Back door latch assembly mechanism dam-
aged or worn. —
Symptom
Suspect systemsRefer to
3 - Ground: Approx. battery voltage
10 - Ground : Approx. battery voltage
WIIA0567E
1 - Ground: Continuity should exist.
2 - Ground : Continuity should exist.
LIIA0801E

FRONT DOOR LOCKBL-131
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
FRONT DOOR LOCKPFP:80502
Component StructureEIS00629
Removal and InstallationEIS0062A
REMOVAL
1. Remove front door speaker. Refer to AV- 5 6 , "FRONT DOOR SPEAKER" .
2. Remove the front door speaker housing and vapor sheet.
3. Remove the door side grommet, and the bolt (TORX T30) from the grommet hole.
4. While pulling the outside handle, remove the door key cylinder assembly or escutcheon.
1. Grommet 2. Front door striker3. Door lock assembly
4. Outside handle cable 5. Inside handle assembly6. Inside handle cable
7. Door lock cable 8. Key cylinder rod (Driver side only) 9. Key cylinder
10. Outside handle bracket 11. Front gasket12. Outside handle
13. Door key cylinder assembly (Driver side) Outside handle escutcheon
(Passenger side) 14. Rear gasket
WIIA0891E
Torx bolt
5.3 N·m (0.54 kg-m, 47 in-lb)
PIIA3553E
PIIA3554E

BL-132
FRONT DOOR LOCK
Revision: November 20092006 QX56
5. Separate the key cylinder rod from the door key cylinder assembly (if equipped).
6. While pulling the outside handle, slide it toward rear of vehicle to
remove.
7. Remove the front and rear gaskets.
8. Remove the TORX bolts (T30), and the door lock assembly.
9. While pulling the outside handle bracket, slide it toward the rear of vehicle to remove it and the door lock assembly.
10. Disconnect the door lock actuator electrical connector.
LIIA0532E
PIIA3557E
Door lock assembly bolts 7.5 N·m (0.77 kg-m, 00 in-lb)
PIIA1090E
PIIA3558E

FRONT DOOR LOCKBL-133
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
11. Separate the outside handle cable connection from the outside
handle bracket.
INSTALLATION
Installation in the reverse order of removal.
CAUTION:
To install each rod, be sure to rotate the rod holder until a click is felt.
Disassembly and AssemblyEIS0062B
DOOR KEY CYLINDER ASSEMBLY
Remove the key cylinder escutcheon pawl and remove the door key cylinder.
PIIA5059E
PIIA4136E