AV-1
AUDIO, VISUAL, NAVIGATION & TELEPHONE SYS-TEM
K ELECTRICAL
CONTENTS
C
D
E
F
G H
I
J
L
M
SECTION
A
B
AV
Revision: November 2009 2006 QX56
PRECAUTIONS .....................................................
..... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
PREPARATION ...................................................... ..... 5
Commercial Service Tool .................................... ..... 5
AUDIO .................................................................... ..... 6
Component Parts and Harness Connector Location ..... 6
System Description ............................................. ..... 8
REAR AUDIO REMOTE CONTROL UNIT ...... ..... 8
SATELLITE RADIO TUNER (PRE-WIRING) ... ..... 9
SATELLITE RADIO TUNER (FACTORY
INSTALLED) .................................................... ..... 9
SPEED SENSITIVE VOLUME SYSTEM ......... ..... 9
Schematic ........................................................... ... 10
Wiring Diagram — AUDIO — .............................. .... 11
Terminals and Reference Value for Audio Unit .... ... 22
Terminals and Reference Value for BOSE Speaker
Amp. .................................................................... ... 25
Terminals and Reference Value for Rear Audio
Remote Control Unit ............................................ ... 28
Terminals and Reference Value for AV Switch .... ... 29
Terminals and Reference Value for Satellite Radio
Tuner (Factory Installed) ..................................... ... 30
AV Switch Self-Diagnosis Function ..................... ... 31
STARTING THE SELF-DIAGNOSIS MODE .... ... 31
EXITING THE SELF-DIAGNOSIS MODE ........ ... 31
DIAGNOSIS FUNCTION .................................. ... 31
Trouble Diagnosis ............................................... ... 32
MALFUNCTION WITH RADIO AND CD .......... ... 32
FOR RADIO ONLY ........................................... ... 32
FOR CD ONLY ................................................. ... 33
FOR SATELLITE RADIO TUNER (FACTORY
INSTALLED) ONLY .......................................... ... 33
Noise Inspection .................................................. ... 33
TYPE OF NOISE AND POSSIBLE CAUSE ..... ... 33
Power Supply Circuit Inspection ......................... ... 35
Satellite Radio Tuner (Factory Installed) Power and
Ground Supply Circuit Inspection ........................ ... 37
Satellite Radio Tuner (Factory Installed) Commu- nication Circuit Inspection ....................................
... 38
Satellite Radio Tuner (Factory Installed) Left Chan-
nel Audio Signal Circuit Inspection ...................... ... 40
Satellite Radio Tuner (Factory Installed) Right
Channel Audio Signal Circuit Inspection ............. ... 41
Steering Switch Check ......................................... ... 41
AV Switch Check ................................................. ... 43
Audio Communication Line Check ...................... ... 44
Sound Is Not Heard From Front Door Speaker or
Front Tweeter ...................................................... ... 44
Sound Is Not Heard From Rear Door Speaker or
Rear Door Tweeter ................................................. 48
Sound Is Not Heard From Center Speaker ......... ... 51
Sound Is Not Heard From Subwoofer .................... 52
Removal and Installation ..................................... ... 55
AUDIO UNIT ..................................................... ... 55
AV SWITCH ...................................................... ... 55
BOSE SPEAKER AMP. .................................... ... 55
CENTER SPEAKER ......................................... ... 56
FRONT DOOR SPEAKER ............................... ... 56
FRONT TWEETER .......................................... ... 56
REAR AUDIO REMOTE CONTROL UNIT ....... ... 57
REAR DOOR SPEAKER .................................. ... 57
REAR DOOR TWEETER ................................. ... 57
SATELLITE RADIO ANTENNA ........................ ... 58
SATELLITE RADIO TUNER ............................. ... 58
STEERING WHEEL AUDIO CONTROL
SWITCHES ...................................................... ... 59
SUBWOOFER .................................................. ... 59
AUDIO ANTENNA ................................................. ... 60
System Description .............................................. ... 60
Wiring Diagram — W/ANT — .............................. ... 61
Location of Antenna ............................................. ... 62
Window Antenna Repair ...................................... ... 62
ELEMENT CHECK ........................................... ... 62
ELEMENT REPAIR .......................................... ... 63
TELEPHONE .......................................................... ... 64
Component Parts and Harness Connector Location ... 64
System Description .............................................. ... 65
BLUETOOTH® HANDS-FREE PHONE SYS-
AV-3
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
*** ” is Shown) .....................................................
. 153
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) ............................................................ . 154
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ...................................... . 154
WARNING DOOR OPEN Screen is Not Shown . . 154
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ........................................... . 155
Audio Does Not Work .......................................... . 155
Navigation System Does Not Activate ................ . 155
Previous NAVI Conditions are Not Stored ........... . 156
Previous Vehicle Conditions are Not Stored ....... . 156
Position of Current Location Mark is Not Correct . 156
Radio Wave From GPS Satellite is Not Received . 156
Driving Test ......................................................... . 157
Example of Symptoms Judged Not Malfunction . . 158
BASIC OPERATION ........................................ . 158
VEHICLE MARK .............................................. . 158
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............ . 159
VOICE GUIDE .................................................. . 159
ROUTE SEARCH ............................................. . 160
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ............................................. . 161
CURRENT-LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ....... . 164CURRENT-LOCATION MARK JUMPS ............
.164
CURRENT-LOCATION MARK IS IN A RIVER OR
SEA .................................................................. .165
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE .............................................................. .165
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ................................................... .165
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ............................... .165
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED ............................................................ .165
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ....... .165
Program Loading of NAVI Control Unit ................ .166
Removal and Installation ..................................... .167
AV SWITCH ...................................................... .167
DISPLAY CONTROL UNIT ............................... .167
DISPLAY UNIT ................................................. .167
GPS ANTENNA ................................................ .167
NAVI CONTROL UNIT ..................................... .168
STEERING WHEEL AUDIO CONTROL
SWITCHES ...................................................... .168
AUDIOAV-9
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
through audio unit terminals 26, 27, 28 and 29
to terminals 1, 2, 3, and 4 of rear audio remote control unit.
SATELLITE RADIO TUNER (PRE-WIRING)
NOTE:
The satellite radio pre-wiring allows connection of a satellite radio tuner.
Power is supplied at all times
through 20A fuse [No. 31, located in the fuse and fusible link box]
to satellite radio tuner terminal 32.
With the ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No. 4, located in the fuse block (J/B)]
to satellite radio tuner terminal 36.
Audio signals are supplied
through satellite radio tuner terminals 21, 22, 23 and 24
to terminals 41, 42, 43 and 44 of audio unit.
Ground is supplied through the case of the satellite radio tuner.
SATELLITE RADIO TUNER (FACTORY INSTALLED)
NOTE:
Factory installed satellite radio systems may be identified by the location of the satellite radio tuner (factory
installed) antenna. Factory installed satellite radio antennas are installed on the front of the roof. Dealer
installed antennas may be installed anywhere on the roof.
Power is supplied at all times
through 20A fuse [No. 31, located in the fuse and fusible link box]
to satellite radio tuner (factory installed) terminal 32.
With the ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No. 4, located in the fuse block (J/B)]
to satellite radio tuner (factory installed) terminal 36.
Radio signals are supplied from the satellite radio antenna to satellite radio tuner (factory installed) terminal
37.
Audio signals are supplied
through satellite radio tuner (factory installed) terminals 21, 22, 23 and 24
to terminals 41, 42, 43 and 44 of audio unit.
Ground is supplied through the case of the satellite radio tuner (factory installed).
SPEED SENSITIVE VOLUME SYSTEM
Volume level of this system goes up and down automatically in proportion to the vehicle speed. The control
level can be selected by the customer. Refer to Owner's Manual for operating instructions.
AV-22
AUDIO
Revision: November 20092006 QX56
Terminals and Reference Value for Audio UnitEKS00BIB
Terminal
(Wire color) ItemSignal
input/
output Condition
Reference value
(Approx.) Example of symptom
+ – Ignition
switch Operation
2 (W) 1 (B) Audio sound
signal front
LHOutput ON
Receive audio
signal No sound from front
door speaker LH or
tweeter LH.
4 (Y) 3 (BR) Audio sound
signal front
RHOutput ON
Receive audio
signal No sound from front
door speaker RH or
tweeter RH.
5 (G/W) Ground Antenna
signal
Output ON
–More than 10V Poor radio reception.
6 (Y) Ground Battery
powerInput
–– Battery voltageSystem does not
work properly.
7 (BR) Ground Illumination
control sig-
nalInput ON Illumination con-
trol switch is
operated by light-
ing switch in 1st
position. Changes between 0 and 12V
Audio unit illumina-
tion cannot be con-
trolled.
8 (R/L) Ground Illumination
signal
Input OFF Lighting switch is
in 1st position.
Battery voltageAudio unit illumina-
tion does not come
on when lighting
switch is in 1st posi-
tion.
Lighting switch is
OFF.
3V or less
9 –Shield –– – 0VInterference and dis-
tortion heard from
speakers.
10 (V) Ground ACC signal Input ON –Battery voltage System does not
work properly.
12 (G/W) Ground Amp. ON
signalOutput ON
–More than 6.5V Amp. does not work
properly.
14 (BR) 13 (B/R) Audio sound
signal rear
LHOutput ON
Receive audio
signal No sound from rear
door speaker LH or
rear door tweeter LH.
16 (L) 15 (B/W) Audio sound
signal rear
RH
Output ON
Receive audio
signal No sound from rear
door speaker RH or
rear door tweeter
RH.
SKIA0177E
SKIA0177E
SKIA0177E
SKIA0177E
AV-30
AUDIO
Revision: November 20092006 QX56
Terminals and Reference Value for Satellite Radio Tuner (Factory Installed)EKS00GB2
17 (Y/B) GroundCD LOAD
signal Output ON Pressed
0V
CD load does
not function.
Released 5V
Terminal No.
(Wire color) ItemSignal
input/
output Condition
Voltage
(Approx.) Example of
symptom
+ – Ignition
switch Operation
Te r m i n a l
(Wire color) ItemSignal
input/
output Condition
Voltage
(approx.)
+ – Ignition
switch Operation
22 (R) 21 (G) Audio signal LH Output ON Receive audio signal.
24 (W) 23 (B) Audio signal RH Output ON Receive audio signal.
25 –Shield ––
– –
26 ONApprox. 0 V
28 (L) Ground REQ1
(SAT-AUDIO) Output ON
Set to the satellite radio
mode
29 (O/L) Ground Communication signal
(SAT-AUDIO)
Output ONSet to the satellite radio
mode
30 (W/L) Ground Communication signal
(AUDIO-SAT)
Input ONSet to the satellite radio
mode
32 (Y) GroundBattery power supply
InputOFF
− Battery voltage
36 (V) ACC power supply ACC
37 –Antenna signal –– –
SKIB3609E
SKIB3609E
SKIB3825E
SKIB3824E
SKIB3826E
AV-32
AUDIO
Revision: November 20092006 QX56
Trouble DiagnosisEKS00BIG
The majority of the audio troubles are the result of outside causes (bad CD, electromagnetic interference,
etc.). Check the inspection items below to diagnose the malfunction.
MALFUNCTION WITH RADIO AND CD
Before proceeding, confirm that other AV switch functions (except audio functions) operate. If not, refer to AV-
155, "Unable to Operate All of AV Switches (Unable to Start Self-Diagnosis)" .
FOR RADIO ONLY
SymptomPossible cause
Inoperative
Audio unit power circuit check. Refer to AV- 3 5 , "Power Supply Circuit
Inspection" .
Audio communication line check. Refer to AV-136, "Audio Communication
Line Check (Between Display Control Unit and Audio Unit)" .
AV switch check. Refer to AV- 4 3 , "AV Switch Check" .
If above check is OK, replace audio unit.
Steering switch does not operate
Steering switch check. Refer to AV-41, "Steering Switch Check" .
AV switch check. Refer to AV- 4 3 , "AV Switch Check" .
If above check is OK, replace audio unit.
Audio information is not displayed on screen
Display unit check. Refer to AV- 11 2 , "Self-Diagnosis Mode (DCU)" .
All speakers do not sound
Audio unit
BOSE speaker amp. power supply and ground circuit check. Refer to AV- 3 5 ,
"Power Supply Circuit Inspection" .
BOSE speaker amp. ON signal
BOSE speaker amp.
One or several speakers do not sound
Front door speaker check. Refer to AV-44, "Sound Is Not Heard From Front
Door Speaker or Front Tweeter" .
Rear door speaker check. Refer to AV- 4 8 , "Sound Is Not Heard From Rear
Door Speaker or Rear Door Tweeter" .
Subwoofer check. Refer to AV- 5 2 , "Sound Is Not Heard From Subwoofer" .
Center speaker check. Refer to AV- 5 1 , "Sound Is Not Heard From Center
Speaker" .
Poor sound
Audio unit
BOSE speaker amp.
Speaker
Noisy
Audio unit
BOSE speaker amp.
Electrical equipment (generator, bonding wire, etc.)
Symptom Possible cause
No sound
Audio unit
Antenna feeder, wiring or connections
Antenna amplifier, power supply, wiring or connections
Noisy
Audio unit
Audio unit case ground
Antenna feeder, wiring or connections
Antenna amplifier, power supply, wiring or connections
Noise prevention parts
Each electrical equipment
Wire harness of each piece of electrical equipment
All radio stations stored in memory are deleted
Audio unit power circuit check. Refer to AV-35, "Power Supply Cir-
cuit Inspection" .
Audio unit
AUDIOAV-33
C
DE
F
G H
I
J
L
M A
B
AV
Revision: November 2009 2006 QX56
NOTE:
1. The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.
Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.
Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the
antenna at a different time from the waves which reflect off mountains or buildings.
FOR CD ONLY
FOR SATELLITE RADIO TUNER (FACTORY INSTALLED) ONLY
NOTE:
Pressing the SAT button, the display unit will display `NO SAT' when the following conditions exist:
Loss of power to the satellite radio tuner (factory installed)
Open or short in the REQ1, TXD, or RXD circuits.
If the satellite antenna is disconnected or inoperative, the display unit will display ANTENNA.
Noise InspectionEKS00BIH
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Symptom Possible cause
CD cannot be inserted.
CD
Audio unit
CD cannot be ejected.
The CD cannot be played.
The sound skips, stops suddenly, or is distorted.
Symptom
Possible cause
Inoperative
Satellite radio tuner (factory installed) power and ground circuit inspection.
Refer to AV- 3 7 , "
Satellite Radio Tuner (Factory Installed) Power and Ground
Supply Circuit Inspection" .
Satellite radio tuner (factory installed) communication circuit inspection.
Refer to AV- 3 8 , "
Satellite Radio Tuner (Factory Installed) Communication
Circuit Inspection" .
If above check is OK, replace satellite radio tuner (factory installed). Refer
to AV- 5 8 , "
SATELLITE RADIO TUNER" .
Right or left channel does not sound
Satellite radio tuner (factory installed) right channel audio signal circuit
inspection. Refer to AV-41, "
Satellite Radio Tuner (Factory Installed) Right
Channel Audio Signal Circuit Inspection" .
Satellite radio tuner (factory installed) left channel audio signal circuit
inspection. Refer toAV- 4 0 , "
Satellite Radio Tuner (Factory Installed) Left
Channel Audio Signal Circuit Inspection" .
If above check is OK, replace satellite radio tuner (factory installed). Refer to
AV- 5 8 , "
SATELLITE RADIO TUNER" .
Poor reception
Location of vehicle. Make certain vehicle is in an open area.
Satellite radio antenna or antenna feeder. Refer to AV- 6 2 , "Location of
Antenna" .
Noisy
Satellite radio tuner (factory installed) ground.
Satellite radio tuner (factory installed) harness shield wires.
Electrical equipment (generator, bonding wire, etc.). Refer to AV-33, "Noise
Inspection" .
AV-58
AUDIO
Revision: November 20092006 QX56
2. Remove rear door tweeter screws and remove rear door
tweeter.
3. Disconnect rear door tweeter connector.
Installation
Installation is in the reverse order of removal.
SATELLITE RADIO ANTENNA
Removal
1. Lower headliner. Refer to EI-38, "HEADLINING" .
2. Disconnect satellite radio antenna connector.
3. Remove satellite radio antenna nut.
4. Remove satellite radio antenna.
Installation
Installation is in the reverse order of removal.
SATELLITE RADIO TUNER
Removal
1. Remove BCM. Refer to BCS-20, "BCM" .
2. Remove the accelerator pedal. Refer to ACC-3, "
ACCELERATOR CONTROL SYSTEM" .
3. Disconnect Bose speaker amp. and satellite radio tuner connectors.
4. Remove Bose speaker amp./satellite radio tuner bracket screws and slide Bose speaker amp./satellite radio tuner bracket down.
WKIA1494E
LKIA0679E
WKIA1605E