2006 INFINITI M35 stall

FLOOR SIDE FAIRING
EI-23
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 January2006 M35/M45
FLOOR SIDE FAIRINGPFP:74586
Removal and Installation of Under Cover (for V6 Engine Models)NIS0024M
Removal and Installation of Under Cover (for V8 Engine Models)NIS0024N
FRONT UNDER COVER
Removal
1. Remove front under cover mounting bolts and clip.
2. Remove front under cover.
Installation
Install in the reverse order of removal.
1. Front under cover 2. Front under cover (rear) 3. Floor under cover (RH)
4. Floor under cover (LH) 5. Rear under cover (RH) 6. Rear under cover (LH)
7. Rear diffuser
PIIB6282E
1. Front under cover 2. Front under cover (rear) 3. Floor under cover (RH)
4. Floor under cover (LH) 5. Rear under cover (RH) 6. Rear under cover (LH)
7. Rear diffuser
PIIB6283E

EI-24
FLOOR SIDE FAIRING
Revision: 2006 January2006 M35/M45
FRONT UNDER COVER (REAR)
Removal
1. Remove front under cover (rear) mounting bolts.
2. Remove front under cover (rear).
Installation
Install in the reverse order of removal.
FLOOR UNDER COVER
Removal
1. Remove floor under cover mounting bolts, nuts and clips.
2. Remove floor under cover.
Installation
Install in the reverse order of removal.
REAR UNDER COVER
Removal
1. Remove rear under cover mounting bolts.
2. Remove rear under cover.
Installation
Install in the reverse order of removal.
REAR DIFFUSER
Removal
1. Remove rear diffuser mounting bolts, nuts and clips.
2. Remove rear diffuser.
Installation
Install in the reverse order of removal.

ROOF SIDE MOLDING
EI-25
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 January2006 M35/M45
ROOF SIDE MOLDINGPFP:73854
Removal and InstallationNIS0024O
REMOVAL
1. Apply protective tape around roof side molding.
2. Disengage clips while pinching molding from rear end of rear
window to front end of front window, and then remove roof side
molding.
CAUTION:
Front and rear ends of roof side molding are placed under
the body side. Pull them out after disengaging plastic clip
joints.
NOTE:
Molding fasteners of front windshield glass and rear window glass are secured with rivet. Remove and
install front windshield glass and rear window glass when replacing the molding fasteners.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
1. Roof side molding 2. Roof outer panel 3. Windshield glass
4. Clip (body side) 5. Molding fastener 6. Rivet
7. Clip (molding side) 8. Body side outer clip
PIIB2753J
PIIB2749J

EI-26
ROOF SIDE MOLDING
Revision: 2006 January2006 M35/M45
INSTALLATION
1. Place roof side molding on roof groove, and then insert the end into front fender.
2. Align roof side molding clips (molding side) (2),(3), and (4) of front pillar with fastener position, and then
insert roof side molding clip (molding side) (1).
3. Insert roof side molding clips (molding side) of front pillar in order of (2) to (4) into molding fastener.
4. Insert body side outer clips of roof in the order of (5) to (9).
5. Insert rear end of roof side molding into trunk lid.
6. Temporarily set roof side molding clips (molding side) of rear pillar on fasteners and insert them in the
order of (10) to (13).
CAUTION:
Be careful not to damage the body.
PIIB4179J

DOOR SASH MOLDING
EI-27
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 January2006 M35/M45
DOOR SASH MOLDINGPFP:80282
Removal and InstallationNIS0024P
FRONT DOOR SASH MOLDING
Removal
1. Remove front door weather-strip. Refer to BL-194, "Door Weatherstrip" .
2. Release roof portion of glass run.
3. Remove screw of front door sash molding.
4. Remove door sash molding connection between door panel and molding from glass run side and remove
molding.
Installation
Install in the reverse order of removal.
REAR DOOR SUSH MOLDING
Removal
1. Remove rear door weather-strip. Refer to BL-194, "Door Weatherstrip" .
2. Release roof portion of glass run.
3. Remove screw of rear door sash molding.
4. Remove door sash molding connection between door panel and molding from glass run side and remove
molding (front).
Installation
Install in the reverse order of removal.
1. Front door sash molding 2. Front door sash outer cover 3. Rear door sash molding
4. Rear door sash outer cover 5. Rear door corner cover 6. Door glass run
7. Door glass
PIIB5694E

EI-28
DOOR SASH MOLDING
Revision: 2006 January2006 M35/M45
DOOR SASH OUTER COVER
Removal
1. Remove front door weather-strip, rear door weather-strip. Refer
to
2. Remove double-faced adhesive tape with (wide) plastic spatula
and remove door sash outer cover.
Installation
Install in the reverse order of removal.
NOTE:
If door sash outer cover is reused, remove double-faced adhesive tape from molding and body sides, clean
the applied area, and then install the parts shown in the figure into the body after applying new double-sided
tape to it.
CAUTION:
Do not let air between contact surfaces when installing.
To secure contact, do not wash vehicle within 24 hours after installation.
REAR DOOR CORNER COVER
Removal
1. Remove rear door finisher. Refer to EI-34, "DOOR FINISHER" .
2. Remove rear door sash cover inner. Refer to EI-36, "
REAR DOOR SASH COVER INNER" .
3. Remove bolts of rear door corner cover and remove rear door corner cover.
Installation
Install in the reverse order of removal.
PIIB4515E

DOOR OUTSIDE MOLDING
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 January2006 M35/M45
DOOR OUTSIDE MOLDING PFP:82820
Removal and InstallationNIS0024Q
FRONT DOOR OUTSIDE MOLDING
Removal
1. Fully open door window.
2. Remove door trim. Refer to EI-34, "
DOOR FINISHER" .
3. Remove front door sash cover inner. Refer to EI-36, "
FRONT DOOR SASH COVER INNER" .
4. Disconnect harness connector for tweeter (only for models with tweeter). Refer to AV- 2 8 6 , "
Tw e e t e r" .
5. Remove door mirror. Refer to GW-120, "
Removal and Installation" .
6. Disengage pawls by inserting a screwdriver to front and rear of
pawl inter grated with cap.
7. Remove door outside molding while pulling up molding using plastic spatula after disengaging.
1. Door outside molding (front) 2. Door outside molding (rear) 3. Door mirror
4. Front door outer 5. Rear door outer
PIIB2754J
PIIB4192J

EI-30
DOOR OUTSIDE MOLDING
Revision: 2006 January2006 M35/M45
CAUTION:
Be careful not to apply excessive force when removing because it is easy to deform parts.
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
Installation
Install in the reverse order of removal.
NOTE:
Molding rear end is flush with door sash rear end when installing.
REAR DOOR OUTSIDE MOLDING
Removal
1. Fully open door window.
2. Remove door trim. Refer to EI-34, "
DOOR FINISHER" .
3. Remove rear door sash cover inner. Refer to EI-36, "
REAR DOOR SASH COVER INNER" .
4. Disengage pawls by inserting a screwdriver to front and rear of pawl integrated with cap.
5. Remove door outside molding while pulling up molding using plastic spatula after disengaging.
CAUTION:
Be careful not to apply excessive force when removing because it is easy to deform parts.
After removal, visually inspect molding, and if it is deformed, replace it with new molding.
Installation
Install in the reverse order of removal.
NOTE:
Molding rear end is flush with door sash rear end when installing.