2006 GREAT WALL HOVER clock

Safety airbag-28
SRS translation wiring harness
releases wring harnessshorting site
6m plus
the shroud
protection tube
Safety airbag module abandoning instruction
Carry out the operation according to the following procedure to abandon a safety airbag module or a vehicle with the SRS
safety airbag. First of all, release the safety airbag.
Unreleased safety airbag module abandoning
Caution
First release the SRS safety airbag when abdbdon it.
Release the safety airbag outside the vehicle to replace the safety airbag module.
Conduct the operation somewhere next to a smoke tester due to the smoke during the safety airbag’s release.
Tell the people to cover their ears and try to conduct the operation somewhere far away from the residential area due
to the big noise during the safety airbag’s release.
Remove the accumulator positive and negative and remove the accumulator off the vehicle.
Caution
Continue the operation 60 seconds after the removal of accumulator positive and negative.
Release the safety airbag module according to the following procedure.
1. Driver’s side safety airbag module
a. Remove the blocking lever
b. Remove the clock spring 2# joint and instrument panel wiring harness joint (yellow)(figure 8.6)
Caution
The clock spring joint will short automatically after the removal of clock spring from the instrument wiring harness,
which can prevent any possible major accident caused by the incorrect release of driver’s side safety airbag module duo
to the static interference from happening.
c. Connect the SRS safety airbag translation wring harness with 2 6m plus release wiring harnesses, wrap the joint part with
insulating tape for insulation.

Safety airbag-29
auto body outer panel.
release wiring harness
auto body outer panel.
releases wring harness. Mutually connect (short) the other end of release wring harness to avoid the possible incorrect release caused by the static
interference.
d. At the clock spring’s 2# joint, tract the translation wiring harness out of the vehicle with the release wiring harness (Figure 9.2)
e. Close all the windows and doors and wear the guard to reduce the noises.
Caution
The guard should be worn because the glass with cracks is very fragile.
f. Shut off the joint of driver’s side safety airbag release wiring harness somewhere far from the vehicle, and connects the joint
with the accumulator and makes the safety airbag release.
clock spring connector clipclock spring
srs translation wiring harness
release wiring harness
Caution
Continue the operation after the confirmation of nobody is in or next to the vehicle.
Its gas generator is quite hot after the driver’s side safety airbag’s release, it can be used after its cooling down for more
than 30 minutes.
Contact with the local service station of the Great Wall Auto Stock Corporation if the driver’s side safety airbag module
cannot be released.
g. Abandon the released driver’s side safety airbag module according to the instructions.

Safety airbag-15
Y esPr
esen t f
ailu re codes
R e plac e S R S saf ety airb ag system unit
S e e h e removal/ins talla tion ofS R
S
sa f ety airb ag system unit
Hi stor y a ccum ulated failu re code
s
T h e e nd offailur e d iagn osis4 Pl
ac e t he i gnition switch i nL O C K position
R e l eas e a ccum ulator negative wire and w ait f or 1 m inut
e
pl us
R e mo vethe l eft t rim c over
Sh ut off S R S safety airb ag system unit tran slat io
n
co nn ecto r cl ips
I n stal l b ack t he
accu mulato r n egativ e w ire, plac e t he
ig nition switch inON position
I s the p oten tial of S R S s afety a irba g s ystem u nit c
onne ctor
cl ip s s titc h 5 , 6( g roun ding ) a bove 9V
? No
R eplac e w irin g h arne ss
Drive side failure
Failure code
$9021
$9022
$9024
$9025
Driver’s side safety airbag failure (high or low resistance, shorting grounding, etc.)
Test
condition
Warning
If not correctly handled, the safety airbag module as well as pretension safety belt may possibly be trigged, released
and tensioned, thus make serene damage to people. Therefore, please carefully read the repairing warning before
trouble handling. Please take references in safety airbag system repairing warning
Driver’s side safety airbag
The resistance between the SRS safety airbag system connector clips connectors not within the designated scope
SRS safety airbag system driver’s side airbag relative wiring harness shorting or shutoff
Possible
causes
Driver’s side safety airbag module failure
Clock spring internal failure
Failure of circuit connector clips between clock spring and SRS safety airbag system electronic-control unit
Shutoff or shorting of wiring harness between clock spring and SRS safety airbag system electronic-control unit.
Misconnection of SRS safety airbag system driver’s side airbag generator connector clip
Procedure Test Operation
Normal Next step
1
Check the clock spring
Warning
If not correctly handled, the safety airbag module may possibly be
trigged and released thus make serene damage to people. Therefore,
please carefully read the repairing warning before trouble handling.
Please take references in safety airbag system repairing warning.
Are the relative parts of clock spring normal? (The relation between
stitches, unnecessary shutoff or shorting?) if the present clock spring can
be replaced by a better one.
Abnormal
Replace the clock spring
Take references in the
removal/installation for
safety airbag system and
clock spring
Can
Replace the driver’s side
safety airbag module
Take references in the
removal/installation for
driver’s side safety airbag
in safety airbag system
2
Confirm the failure in driver’s side safety airbag module or other parts.
Replace the DAB module with a better one
Install back accumulator negative wire
Place the ignition switch in ON position
Is the failure code still in display or can be debugged?
No Next step
Normal Next step
3
Check clock spring wiring harness connector clip
Place the ignition switch in LOCK position
Release accumulator negative wire and wait for 1 minute plus
Remove steering pillar shell
Release the clock spring connector clip, is it in normal condition? Abnormal Replace the wiring
harness

Safety airbag-16
Yes Next step
4 Confirm the failure in clock spring or other parts
configure the special tools fuel and t emperature diagnostic instrument
at 2Ω position
Install back the accumulator negative wire
Place the ignition switch in ON place
Any failure code in display? No Replace clock spring
Take references in the removal
and installation for safety airbag
system and clock spring.
Nor mal Replace SRS safety airbag
system unit; take references in
removal/installation of SRS
safety airbag system unit.
5 Check the wiring harness between clock spring and SRS safety airbag
system electronic-control unit
Place the ignition switch in LOCK position
Release accumulator negative wire and wait for 1 minute plus
Remove PAB trim cover, glove box (passengers’ side safety airbag is
under the trim cover)
Release the passengers’ side safety airbag module connector clip
Release all SRS safety airbag system unit connector clips
Check whether the following troubles are with the harness between
connector clips terminals of SRS safety airbag system unit and clock
spring
Grounding
Power-supply shorting
Shutoff
Is the previous wiring harness normal? Abnormal Replace the wire harness
Nor mal Next step
6 Check the clock spring connector clip
Remove the steering pillar shell
Release the clock spring connector clip
Is the clock spring connector clip normal? Abnormal Replace the wiring harness or
connector clips

Nor mal Next step
7 Check clock spring
Remove clock spring
Take references in removal/installation of safet y airbag system as
well as clock spring
Check clock spring
Take references in the test for safety airbag system and clock spring.
Is the clock spring normal? Abnormal Replace clock spring
Take references in the
removal/installation of safety
airbag system and clock spring.
Nor mal Next step
8 Check the wiring harness between clock spring and SRS safety airbag
system electronic-control unit
Place the ignition switch in LOCK position
Release accumulator negative wire and wait for 1 minute plus
Remove PAB trim cover, glove box (passengers’ side safety airbag is
under the trim cover)
Release the passengers’ side safety airbag module connector clip
Release all SRS safety airbag system unit connector clips.
Check whether the following troubles are with the harness between
connector clips terminals of SRS safety airbag system unit and spring
clock.
Grounding
Power-supply shorting
Shutoff
Is the previous harness normal? Abnormal Replace clock spring
Take references in the
removal/installation of safety
airbag system, and clock spring

Safety airbag-18
Nor mal Present failure code
Replace SRS safety airbag system
unit
Take references in
removal/installation of SRS
safety airbag system unit in safety
airbag system.
History-accumulated failure
codes
The end of failure diagnosis
4 Check the wiring harness between passengers’ side safety airbag
module and SRS safet y airbag system electronic-control unit
Place the ignition switch in LOCK position
Release accumulator negative wire and then wait for about 1
minute plus
Remove steering pillar shell
Release clock spring connector clip
Release driver’s and passengers’ side safety airbag module
connector clips
Release all SRS safety airbag system unit connector clips
Check whether the following troubles are with the circuit of the
connector clips terminals between SRS safety airbag system
electronic-control unit and passengers’ side safety airbag
module
Grounding
Power-supply shorting
Shutoff
Is the previous circuit normal? Abnormal Replace the relative wiring
harness
Impact-vehicle diagnosis
Test SRS-ECU diagnostic signals
1. Connect the (X-431 diagnostic test’s) diagnostic joint
2. Read the diagnostic results with X-431 diagnostic tester
Repairing procedure
1.When safety airbag is released.
The following parts should be replaced with new ones
a. Passengers’ side safety airbag module
b. SRS-ECU
c. Driver’s side safety airbag module
2 Check the following parts; replace them with new ones providing something wrong with them.
a. Clock spring
b. Steering-wheel, steering column, bottom steering shaft module
3.Driver’s side safety airbag module’s installation status towards the steering wheel.
a. Check whether abnormal knocking is with the steering wheel, its activity is in good condition and its clearance is normal.
b. Check whether the wiring harness joint is broken and its terminal is deformed.
Caution: Due to the impact, the diagnostic instrument cannot communicate with SRS-ECU when accumulator is lack of
power, in this case, check and maintain the instrument panel wiring harness or utilize the extension power supply.