2006 GREAT WALL HOVER diagram

Instroduction-5
e. Mount the cable terminal onto the binding post of the loosened nut,
then tighten the nut. Does not use hammer to knock at the terminal
onto the post.
f. Do remember to check whether the positive pole (
) terminal cap
is in its position.
4. Check all the soft tubes and wire terminal, check to see whether
they are connected correctly and firmly.
5. Used component which can not be used any more.
a. The following spare parts needs always to be renewed: split pin,
seal gasket, O ring and oil seal, etc.
b. For the used component which can not be used any more, it is
indicated by symbol “¦” in elements diagram.
6. Precoated component
The precoated component includes the bolt and nut which is precoated
with the locking sealant in factory.
a. If the precoated component is tightened, loosed or moved by any
reason, it must be recoated with the specified sealant.
b. Coating procedure of precoated component
Remove the old sealant from the screw of component by washing.
Dry it by compressed air.
Coat the screw of components with the specified locking sealant.
c. The precoated component is indicated by symbol “?” in elements
diagram.
7. It can use the sealant or seal ring to prevent the leakage if
necessary.
8. Abide by all specifications for bolt torque strictly. It should use
the torque wrench.
Comprehensive maintenance instruction
1. Use the protection plate, seat and floor covering cloth to make
the car clean and prevent it from being damaged.
2. During the disassembling, place the components in order for the
convenience of assembly.
Observe the following issues:
a. Before conducting the electrical work, remove the negative pole of
the cable from the accumulator terminal.
b. When it is necessary to remove the accumulator for checking or
maintenance, the cable shall be removed from the negative pole
(
) connected to the car body.
c. In order to avoid the damage of accumulator terminal, when removing
the cable, loosen the terminal nut, then pull the cable upwards
vertically, do not twist or pry it.
d. Please use cleaning cloth to clean the accumulator terminal. Do not
use file or other similar tools, which may scuff them.

Preface
Table of Contents
Instruction How to use the manual
Chapter 1 Overview of the entire car (parameters)
Chapter 2 Fuel supply system and exhaust air system
Chapter 3 Clutch
Chapter 4 Transmission
Chapter 5 Automatic transmission
Chapter 6 Driving shaft
Chapter 7 Suspension and vehicle axle
Chapter 8 Brake (ABS)
Chapter 9 Steering
Chapter 10 Car body electric appliance
Chapter 11 CD player and air-conditioning system
Chapter 12 Safety airbag
Annex:
Important components guarantee and requirement
List of non-metal material consumption
Special tools
D Important working components and tightening torque
E Electric wiring diagram

Structure diagram of SC5M2D-C and SC5M4D-C transmission: shown in figure
Structure diagram of SC5M2D-C transmission
Structure diagram of SC5M4D-C transmission
Specification of transmission

2. Operation of 4WD
The operating auxiliary steering column can be shifted to 4WD status.
For position of auxiliary steering column and corresponding operating
condition refer to table.
3. Caution for operation:
a. Do not use 4WD in good surface, otherwise the tyre and components
of drive system will be damaged easily and increase the consumption
of fuel, and cause the noise of drive system.
b. Please run in 1st-Gear under “4L” gear position when run in very
low speed in field.
Operating instruction of transmission SC5M4D-C
1.The schematic diagram of transmission operating gear position
is on the handle of steering column.
During the process after vehicle is started and in traveling, it must
step the clutch pedal to bottom before the shifting. If need shift from
5
th-Gear to reverse-Gear, it should move the shifting bar to the neutral
position of 3rd/4th-Gear. Shift to R-Gear after stop the vehicle stably,
otherwise, it can not shift.
During the traveling process. It should always pay attention to the
shifting to make the vehicle matches to the speed of engine. The
correct shifting can improve the economical efficiency and prolong
the service life of engine. Do not shift from high-Gear to low-Gear on
the condition that the pointer of tachometer may enter into red area,
otherwise, the engine will be damaged.
Warning: Do not shift to reverse-Gear when the vehicle moves
forwardly, otherwise the transmission will be damaged.
hand hall of main steering column
hand ball of auxiliary steering column
Auxiliary steering
column position drive Operating condition
2H 2WD Use this gear position when run in the general railway and high speed highway.
4H High speed 4WD Use this gear position when run in the deep snowland, sand ground or uneven road
in normal speed.
N Neutral gear When use the gear position during using of winch, it could not drive the vehicle.
4L Low speed 4WD Use this gear-position when run in uneven road such as mud land or climbing or
downward （especially when need increas e the power）.

Automatic transmission-10
Figure 3.3 Schematic diagram of temperature sensor position and solenoid valve wiring
2.Throttle position sensor
Figure 3.4 gear sensor
solenoid valve 4 (orange )
ground wire (2)
solenoid valve 7 power supply connectorolenoid valve 6 (violet ) ground wiretemperature sensor solenoid valve (red ) ground wire
solenoid
valve (green )
solenoid valve (yellow )
solenoid valve (blue ) ground wire
ground wire
ground wire

special tools
diagram of special tools
grease
4. Remove the oil seal and inner bearing
a. Use the screwdriver to pry out the oil seal.
b .Remove the inner race of inner bearing from the hub.
Check and repair of front hub
1. Check each bearing
Wash the inner and outer race of each bearing and check them for
damage or wear.
2. Replace the bearing outer race
a. Use the brass bar and hand hammer to knock out the bearing outer
race.
b. Use the special tools to knock in the new bearing outer race.
Assembly of front hub
1. Coat the inner surface of hub and bearing outer race
with the grease.
The grease is the Jin HP-R grease or the grease met the requirement in
following table.
Item Typical data
Dropping point, C
289
Leakage amount (104
C, 6h), g 0.48
EP performance OK value , N
178

2. Place in the bearing inner race; use the fill the gap
between the inner and outer race of the bearing up
with the HP-R grease.grease
grease
3. Install the inner bearing and oil seal
a. Place the inner bearing in the hub.
b. Use the special tools to knock the new oil seal into the hub.
c. Coat the oil seal lip with HP-R grease.
4. Install the hub on the steering knuckle
a. Install the hub on the steering knuckle.
b. Install the external bearing.
diagram of spe-
cial tools
special tools
5. Adjust the pre-applied load
a. Use the special tools to screw on the locknut to specified torque.
Tightening force: 80-100N
m
b. Rotate the hub to right and left 1/3
1/4 round respectively.
c. Screw off the nut until the nut can be loosed by hand.
d. Use the special tools to retighten the lock nut.
Tightening force: 28N
m
e. Use the spring tension meter to check the pre-applied load.
Pre-applied load (for starting): 28-56N
diagram of spe-
cial tools
special tools

special tools
diagram of
special tools
Front hub
Disassembly of front hub
1. Remove the disc brake
Remove the brake caliper and hang it by steel cable.
Remarks: Do not remove the brake pipe and brake hose.
2. Remove the hub cap and flange
a. Use the inner hexagon spanner to screw off the fastening blot
and remove the hub cap.
b. Use the pliers to remove the circlip and remove the adjusting
washer.
c. Remove the flange.
3. Remove the hub and brake disc
a. Use the Philips screwdriver to screw off the tight screw;
remove the lock washer.
b. Use the special tools to remove the lock nut.
c. Remove the hub and brake disc with the outer bearing.