2006 GREAT WALL HOVER torque

Appendix A-2
the fixed torque of nut 2 in the Figure is 7010Nm
the torque is: 70
10Nm the fixed
Connection of steering linkage co-
assembly and fixed torque of nut 1 in the Figure is 25Torque wrench
connection of steering linkage co-
assembly and left carriageTorque wrench
Torque wrench
Connection of left right long longitudinal
tie assembly and carriage and rear axle the fixed torque of nut 1 in the Figure isTorque wrench
the fixed torque of nut 2 in the Figure isTorque wrench
Connection of left right short longitudi-
nal tie assembly and carriagethe fixed torque of nut 3 in the Figure is
Torque wrench
Connection of cross tie assembly and rear
axle assemblythe fixed torque of nut 1 in the Figure isTorque wrench
the fixed torque of nut 1 in the Figure isTorque wrench
steering linkage co-assemblycross universal joint
integral power steering general assembly
Connection of left right short longitudinal
tie assembly and rear axle assembly.
Connection of cross tie assembly and
carriage.
short longitudinal tie assembly (R)
long longitudinal tie assemblyshort longitudinal tie
assembly (L)

Appendix A-3
1. (upper suspension arm steering knuckle ball pin nut) bolt
Locate the rear transverse stabilizer rob in the corresponding
position of carriage, symmetries the left and right during
installation.
Connection of rear transverse
stabilizer rod and rear axleViewing confirmation
the fixed torque of nut 2 in the Figure is 23
3NmTorque wrench
Connection of rear transverse
stabilizer rod and rear transverse
stabilizer robs connecting bar
assembly.the fixed torque of nut 1 in the Figure is 63
5NmTorque wrench
rear transverse stabilizer
rear transverse stabilizer rod connecting bar assembly bush
Upper suspension arm and upper suspension
arm steering knuckle ball pin
Steering gear cross tie ball pin
Lower suspension arm and lower suspension
arm steering knuckle ball pinthe fixed torque of nut 1 in the Figure is
145
15Nm
the fixed torque of nut 2 in the Figure is120
10Nm
the fixed torque of nut 3 in the Figure is 230
20Nm
Torque wrench
Torque wrench
Torque wrench
2. (steering gear cross tie ball pin nut) left steering
knuckle and wheel hub brake assembly
3. (lower suspension arm steering knuckle ball pin nut bolt 4. left steering knuckle and steering knuckle
and wheel hub brake assembly.

Appendix A-4
Connection of front transverse stabilizer rod
and carriage.the fixed torque of nut 1in the Figure is 253Nm
the fixed torque of nut 2in the Figure is 63
5Nm Connection of front transverse stabilizer rob
and front transverse stabilizer rod connecting
bar assemblyTorque wrench
Torque wrench
transmission assembly
drive shaft assemblyrear axle assembly
Drive shaft assembly installationPlug the front part of drive shaft into transmission assembly
splinded shaft, after their good meshing, screw the central bearing
hexagon bolt into the corresponding screw hole of the carriage
Center bearing connecting bolt
the fixed torque of bolt 1 in the Figure is 65
5Nm
Drive shaft bolt
the fixed torque of bolt 2in the Figure is 65
5Nm
Torque wrenchTorque wrench Viewing and handle
confirmation
front transverse stabilizer rod
bush
bush clipfront transverse stabilizer rod
connecting bar assembly

Appendix A-5
drive shaft boltthe fixed torque of bolt 1 in the Figure is 785Nm
front axle drive shaft assembly
transmission assemblyrear axle drive shaft assembly
rear axle assembly
petrol lien joint
petrol line joint tightening torque is 162 N torque wrench
petrol pipe joint
two way valve

Appendix A-6
Driver steering oil pump installation
Fixed torque of tubular hexagon bolt 1 in the Figure is
40N
m
Multi-wedge belt
Multi-wedge belt 4PK1100 tension is 500
50NTorque
Torque
multi-wedge belt 4PK1100driver steering oil pump
cover lock mounting bolt
effect
cover lock mounting bolt’s torque is 92Nm
the cover lock can be opened freely, the position is reliable
without any jam.
cover lock cable
cover lock buckle
fastening blot
cover lock mounting bracket

Appendix A-7
The fixed torque of bolt 1 in the Figure is 61Nm
Out handle can be normally and efficiently used, no linkage
falling off, the backup door can be opened and closed freely
without any jam nor unlocking.Handle confirmation
rear door assembly
backup door bottom buckle
backup door lockbackup door out handle
The door can be opened and closed smoothly without any jam nor
unlocking.Torque wrench
door lock assembly

Appendix A-11
Driver seat assembly installationbolt 1 in the Figure tightening torque:is 3343Nm
Wheel nut fixing procedure
Wheel nut fixed torqueInstallation order is A-C-E-B-D-F as showed in the Figure
Torque wrench
Viewing and handle
confirmation The headrest can be up and down smoothly, angle-adjuster
handle can be normally used, driver, co-driver seat can move
freely and transmission trim cover can be freely opened.
seat assembly
the fixed torque of nut 1 in the Figure is 135
15Nm
brake disc assembly

Appendix D-17
Serial
No. Working region and
specification Torque
N·m Serial
No. Working region and specification Torque
N·m
1 upper arm shaft fixed
bolt M14×1.5-10.9 200 25 engine suspension connecting bolt M10×
1.25-10.9 78±10
2 front shaft of lower arm
connecting bolt M16×
1.5-10.9 270±25 26 transmission suspension connecting bolt M10×
1.25-10.9 78±10
3 rear shaft of lower arm
connecting bolt M18×
1.5-10.9 320±30 27 transmission-engine connecting bolt M10×
1.25-10.9 50±5
4 b ottom ar m l imit ing
stopper fixed bolt M10
×1.25-8.8 63±5 28 drive shaft connecting bolt M10×1.25-10.9 78±5
5 upper arm ball pin
pedestal connecting bolt
M10×1.25-10.9 78±10 29 drive shaft bearing fixed bolt M10×1.25-8.8
65±5
6 bottom ar m ball p in
pedestal connecting bolt
M12×1.25-10.9 140±10 30 wheel nut M12×1.25 135±15
7 front twisted bar
pedestal connecting bolt
M12×1.25-10.9 140±10 31 steering wheel lock nut M12×1.25-8 30±5
8 upper arm ball channel
fixing nut M16×1.5-10 145±15 32 steering gear-carriage fixing nut M12×1.25-8 90±10
70±10
9 front vibration damper
upper fixing nut M10×
1.25-8 Bush
co mpr es sed
by 1/3 33
steering angle drive co-carriage bolt M10×
1.5-9.8 50±5
10 bottom ar m ball p in
channel fixing nut M18
×1.5-10 230±20 34 steering system universal-joint lock bolt M8×
1.25-8.8 25±3
11 front vibration damper
bottom connecting bolt
M12×1.25-8.8 90±10 35 steering linkage ball fixing nut M14×1.5-8 120±10
12 rear vibration damper
upper fixing nut M10×
1.25-8 Bush
co mpr es sed
by 1/3 36 steering linkage adjustment lock nut M14×
1.5-8 60±5
13 rear vibration damper
bottom fixing nut M14
×1.5-8 170±15 37 front axle front shackle connecting bolt M14×
1.5-10.9 180±20
14 front cross stabilizer rod
-carriage fixed bolt M8
×1.25-8.8 23±3 38 front axle rear shackle connecting bolt M14
×1.5-10.9 180±20