2006 ACURA CSX rear brake assembly


Î
Î
(#'



)
14-215
Shift Solenoid Valve Test
A A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft) B
A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
1. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
3. Select Shift Solenoid Valves A, B, C, D, and E Test in the Miscellaneous Test Menu with the HDS.
4. Check that shift solenoid valves A, B, C, D, and E operate with the HDS. A clicking sound should be
heard.
 If a clicking sound is heard, the valves are OK. The test is complete, disconnect the HDS.
 If no clicking sound is heard, go to step 5, and test the solenoid valve.
5. Do the battery removal procedure (see page 22-69).
6. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
7. Remove the battery tray, the battery base, and the resonator.
8. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
9. Remove the splash shield. 10. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF).
11. Reinstall the drain plug with a new sealing washer (B).
12. Remove the shift solenoid valve cover (A), the dowel pins (B), and the gasket (C).
(cont’d)
Replace.
Replace.
08/08/21 14:46:44 61SNR030_140_0217
ProCarManuals.com
DYNOMITE -2009-

Î
Î
Î
(#'



 )
14-217
Shift Solenoid Valve and Shift Solenoid Wire Harness Replacement
A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft) B A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
1. Raise the vehicle on a lift, or apply the parking
brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
2. Remove the splash shield.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Do the battery removal procedure (see page 22-69).
6. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
7. Remove the battery tray, the battery base, and the resonator. 8. Remove the shift solenoid valve cover (A), the
dowel pins (B), and the gasket (C).
9. Disconnect the shift solenoid valve connectors.  If replacing the shift solenoid valve(s), go to step10.
 If replacing the shift solenoid wire harness, remove the shift solenoid wire harness connector
(A), and replace it. Install a new O-ring (B) on a
new shift solenoid wire harness connector, and
install it in the transmission housing, then go to
step 15.
(cont’d)
Replace. Replace.
Replace.
08/08/21 14:46:45 61SNR030_140_0219
ProCarManuals.com
DYNOMITE -2009-

Î
Î

(#'




)

14-229
ATF Temperature Sensor Test/Replacement
A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft) B A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
1. Raise the vehicle on a lift, or apply the parkingbrake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
2. Remove the splash shield.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Do the battery removal procedure (see page 22-69).
6. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
7. Remove the battery tray, the battery base, and the resonator. 8. Remove the shift solenoid valve cover (A), the
dowel pins (B), and the gasket (C).
9. Disconnect the shift solenoid wire harness connector, and remove it from the transmission
housing.
(cont’d)
Replace. Replace.
08/08/21 14:46:51 61SNR030_140_0231
ProCarManuals.com
DYNOMITE -2009-


Î

(#'




)
µ
Transmission Range Switch Subharness
Connector
14-265
Transmission Range Switch Test
A Connector Terminal/Signal
25
134
687910
P
R
N
D
S
Posi-
tion
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
ATP
NP
ATP
FWD
GND
ATP
RVS
ATP
D ATP
R ATP
P ATP
SATP
N
1. Remove the intake air duct (see page 11-348) and
the air cleaner assembly (see page 11-345).
2. Disconnect the transmission range switch subharness connector (A).
3. Check for continuity between the terminals at the harness connector. There should be continuity
between the terminals in the following table for
each switch position. 4. Transmission range switch test has completed if
the test results are OK, go to step 12. If there is no
continuity between any terminals, go to step 5.
5. Raise the vehicle on a lift, or apply the parking brake, block the rear wheels, and raise the front of
the vehicle. Make sure it is securely supported.
6. Remove the transmission range switch cover.
(cont’d)
Terminal side of
male terminals
08/08/21 14:49:01 61SNR030_140_0267
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
µµ
Front and rear wheel radial runout:
Standard: 0 0.7 mm (0 0.03 in.)
Service limit: 1.5 mm (0.06 in.) Special Tools Required
Front
18-1018-10Front and Rear Suspension
Wheel Runout Inspection (cont’d) Wheel Bolt Replacement
Press
A
B
C C
4. Reset the dial gauge to the position shown, and
measure the radial runout.
5. If the wheel runout is not within the specification, check the wheel bearing end play (see page 18-9),
and make sure the mating surfaces on the brake
disc and the inside of the wheel are clean.
6. If the bearing end play is within the specification but the wheel runout is more than the service limit,
replace the wheel. Ball joint remover, 28 mm 07MAC-SL0A202
 Do not use a hammer or impact tools (pneumaticor electric) to remove and install the wheel bolts.
 Be careful not to damage the threads of the wheel bolts.
1. Remove the front hub (see page 18-15).
2. Separate the wheel bolt (A) from the hub (B) using a hydraulic press. Support the hub with hydraulic
press attachments (C) or equivalent tools.
NOTE: Before installing the new wheel bolt, clean
the mating surfaces, on the bolt and the hub.
3. Insert the new wheel bolt into the hub while aligning the splined surfaces on the hub hole with
the wheel bolt.
NOTE: Degrease all around the wheel bolt.
 Make sure the wheel bolt is installed vertically in relation to the hub disc surface.
4. Install the wheel bolt using a hydraulic press until the wheel bolt shoulder is fully seated.
5. Install the front hub (see page 18-15). NOTE: If you cannot tighten the wheel nut to the
specified torque value when installing the wheel,
replace the front hub as an assembly.
08/08/21 14:56:47 61SNR030_180_0010
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
µµ
Front and rear wheel radial runout:
Standard: 0 0.7 mm (0 0.03 in.)
Service limit: 1.5 mm (0.06 in.) Special Tools Required
Front
18-1018-10Front and Rear Suspension
Wheel Runout Inspection (cont’d) Wheel Bolt Replacement
Press
A
B
C C
4. Reset the dial gauge to the position shown, and
measure the radial runout.
5. If the wheel runout is not within the specification, check the wheel bearing end play (see page 18-9),
and make sure the mating surfaces on the brake
disc and the inside of the wheel are clean.
6. If the bearing end play is within the specification but the wheel runout is more than the service limit,
replace the wheel. Ball joint remover, 28 mm 07MAC-SL0A202
 Do not use a hammer or impact tools (pneumaticor electric) to remove and install the wheel bolts.
 Be careful not to damage the threads of the wheel bolts.
1. Remove the front hub (see page 18-15).
2. Separate the wheel bolt (A) from the hub (B) using a hydraulic press. Support the hub with hydraulic
press attachments (C) or equivalent tools.
NOTE: Before installing the new wheel bolt, clean
the mating surfaces, on the bolt and the hub.
3. Insert the new wheel bolt into the hub while aligning the splined surfaces on the hub hole with
the wheel bolt.
NOTE: Degrease all around the wheel bolt.
 Make sure the wheel bolt is installed vertically in relation to the hub disc surface.
4. Install the wheel bolt using a hydraulic press until the wheel bolt shoulder is fully seated.
5. Install the front hub (see page 18-15). NOTE: If you cannot tighten the wheel nut to the
specified torque value when installing the wheel,
replace the front hub as an assembly.
08/08/21 14:56:47 61SNR030_180_0010
ProCarManuals.com
DYNOMITE -2009-


µ
µ
Rear
Limited torque:
108 N·m (11.0 kgf·m, 79.6 lbf·ft) max.
18-11
A
B
D
F
E
C
07MAC-SL0A202 A
B
C
E G
F
D
11 14 mm
(0.43 0.55 in.)
1. Raise the vehicle, and support it with safety stands
in the proper locations (see page 1-11).
2. Remove the rear brake disc (see page 19-34).
3. Separate the wheel bolt (A) from the hub (B) using the ball joint remover (C), and keep the jaw (D) of
ball joint remover vertical against the wheel bolt
(see page 18-12).
NOTE: If the angle of the remover against the wheel bolt is not square, readjust the ball joint remover by
turning the head (E) of the adjusting bolt (F).
 Before installing the new wheel bolt, clean the mating surfaces on the bolt and the hub. 4. Insert the new wheel bolt (A) into the hub (B) while
aligning the splined surfaces (C) on the hub hole
with the wheel bolt. Adjust the measurement (D)
with washers (P/N 94101-12800 or equivalent) (E),
then install a nut (P/N 90304-SC2-000 or equivalent)
(F) hand-tight.
NOTE: Degrease all around the wheel bolt and the threaded section of the nut.
 Make sure the wheel bolt is installed vertically in relation to the hub disc surface.
 Do not install the nut and washers that have been used as tools on a vehicle.
5. Tighten the nut until the wheel bolt is drawn fully into the hub. Do not exceed the maximum torque
limit. Make sure there is no gap (G) between the
bolt and the hub.
6. Install the rear brake disc (see page 19-34). NOTE: If you cannot tighten the wheel nut to the specified torque value when installing the wheel,
replace the rear hub bearing unit as an assembly.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
08/08/21 14:56:48 61SNR030_180_0011
ProCarManuals.com
DYNOMITE -2009-



18-23
B
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft)
C
12x1.25mm
59N·m(6.0kgf·m,43lbf·ft) A
D
12x1.25mm
59 N·m (6.0 kgf·m, 43 lbf·ft) E D
C
B
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
A
14x1.5mm
83 N·m
(8.5 kgf·m, 61 lbf·ft)
5. Remove the flange bolt and the self-locking nuts
from the lower arm (A).
NOTE: During installation, install the new flange
bolt and the new self-locking nuts. After lightly
tightening all three fasteners, tighten them to the
specified torque in the following order, the nut on
the front (B), the nut on the rear (C), then the bolt
(D).
6. Disconnect the lower ball joint (E) from the lower arm. 7. Remove the front side of the lower arm mounting
bolt (A).
NOTE: Use the new mounting bolt during
reassembly.
8. Remove the rear side of the lower arm mounting bolt (B), then remove the lower arm (C) from the
front suspension subframe (D).
NOTE: Use the new mounting bolt during
reassembly.
9. Install the lower arm in the reverse order of removal, and note these items:
 First install all of the components, and lightly tighten the bolts and the nuts, then raise the
suspension to load it with the vehicle’s weight
before fully tightening to the specified torque
values.
 Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the
wheel.
10. Check the wheel alignment, and adjust it if necessary (see page 18-5).
(cont’d)
Replace.
Replace.
Replace. Replace.
Replace.
08/08/21 14:57:36 61SNR030_180_0023
ProCarManuals.com
DYNOMITE -2009-