2006 ACURA CSX transmission oil



(#'
")
Special Tools Required
13-54
Manual Transmission
Mainshaft Thrust Clearance Adjustment
A
M B
B
A
C C
A
07GAJ-PG20110
B
07GAJ-PG20130 D
 Catch adapter 07GAJ-PG20110
 Base adapter 07GAJ-PG20130
NOTE:
 Take measurement at normal room temperature.
 Clean all the parts thoroughly before installation.
1. Remove the 72 mm shim (A) and oil guide plate M from the transmission housing (B).
2. Thoroughly clean the 28 mm spring washer (A) and the 28 mm washer (B) before installing them on the
clutch housings side ball bearing (C).
NOTE: Install the spring washer in the direction
shown.
3. Assemble all of the mainshaft components. NOTE: Refer to the Exploded View, as needed,
during the assembly (see page 13-36). 4. Install the mainshaft assembly into the clutch
housing.
5. Place the transmission housing over the mainshaft and onto the clutch housing.
6. Tighten the clutch and transmission housings with several 8 mm bolts.
NOTE: It is not necessary to use sealing agent
between the housing for this procedure.
7. Lightly tap on the mainshaft with a plastic hammer.
8. Attach the catch adapter (A) and the base adapter (B) to the mainshaft as follows:
 Back out the catch adapter bolt (C), and loosen the two hex bolts (D).
 Fit the catch adapter over the mainshaft so its lip is towards the transmission.
 Align the catch adapter lip around the groove at the inside of the mainshaft splines, then tighten
the hex bolts.
9. Fully seat the mainshaft by tapping its end with a plastic hammer.
10. Thread the catch adapter bolt in until it just contacts thewidesurfaceofthebaseadapter.
08/08/21 14:45:50 61SNR030_130_0056
ProCarManuals.com
DYNOMITE -2009-

Î
Î 

13-57
6x1.0mm
15N·m(1.5kgf·m,11lbf·ft)
A
D C
BA
6x1.0mm
15 N·m
(1.5 kgf·m,
11 lbf·ft) A B
A
M
C
Liquid gasket
4. Install the reverse shift fork (A).
5. Install the reverse idler gear (A) and the reverse idler gear shaft (B) by aligning the mark (C) on the
clutch housing with the r everse idler gear shaft
hole (D).
6. Install the reverse lock cam (A). 7. Selectthepropersize72mmshim(A)accordingto
the measurements made during the Mainshaft
Thrust Clearance Adjustment (see page 13-54).
Install the oil gutter plate (B), oil guide plate M, and
the 72 mm shim into the transmission housing (C).
8. Clean any dirt or oil from the mating surface of the transmission housing and the clutch housing.
Apply liquid gasket, P/N 08718-0001 evenly to the
mating surface of the transmission housing and the
clutch housing. Install the component within
5 minutes of applying the liquid gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
(cont’d)
08/08/21 14:45:52 61SNR030_130_0059
ProCarManuals.com
DYNOMITE -2009-

Î
 Î
Î
Specified Torque:
8x1.25mm
27 N·m (2.8 kgf·m, 20 lbf·ft)
13-59
Liquid gasket
D
39 N·m
(4.0 kgf·m,
29 lbf·ft)
C
B
A
B
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
44 N·m
(4.5 kgf·m, 33 lbf·ft)
G
H
F
A
39 N·m
(4.0 kgf·m,
33 lbf·ft)
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft) D
E
C
C
15. Tighten the 8 mm flange bolts in a crisscross pattern in several steps.
16. Clean any dirt or oil from the mating surface of the change lever assembly and the transmission
housing. Apply liquid gasket, P/N 08718-0001
evenly to the mating surface of the change lever
assembly and the transmission housing. Install the
component within 5 minutes of applying the liquid
gasket.
NOTE:  If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket. 17. Installthe8x14mmdowelpins(B)andthechange
lever assembly (C) with harness bracket A.
18. Apply liquid gasket, P/N 08718-0001, evenly to the threads of the inter lock bolt (D). Install the
component within 5 minutes of applying the liquid
gasket.
NOTE: If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.
 If too much time has passed after applying the liquid gasket, remove the old liquid gasket and
residue, then reapply new liquid gasket.
19. Install the drain plug (A) and the 10 mm flange bolt (B) with new washers (C). Install the filler plug (D)
finger-tight with new sealing washer (E).
20. Apply MTF to a new O-ring (F). Then install the output shaft (countershaft) speed sensor (G) with
the O-ring and the plain washer (H).
(cont’d)
Replace.Replace.
Replace.
Replace.
08/08/21 14:46:29 61SNR030_130_0061
ProCarManuals.com
DYNOMITE -2009-

(#'

/)
Reverse Lockout System
Manual TransmissionM/T Differential
6-Speed Manual Transmission
.............................
................
....................... ...
....................................... ..
..........................
...
................
....................... ...
....................................... ..
General Troubleshooting
Information . 13-71
Component Location Index . 13-72
System Description . 13-73
Circuit Diagram . 13-74
Symptom Troubleshooting . 13-74
Reverse Lockout Solenoid Test . 13-77
Reverse Lockout Solenoid Disassembly/Reassembly . 13-77
........................... ...
..................................... ......................
.......... ...........
............................
............................ ..
............................ ..
..........
...........................
...
..................................... ......................
.......... ...........
............................
............................ ..
............................ ..
..........
Special Tools
. 13-70
Component Location Index . 13-79
Symptom Troubleshooting Index . 13-80
Transmission Fluid Inspection and Replacement . 13-82
Back-up Light Switch Test . 13-83
Transmission Removal . 13-84
Transmission Installation . 13-91
Transmission Disassembly . 13-99
Reverse Shift Fork Clearance Inspection . 13-
Change Lever Clearance Inspection . 13-
Change Lever Assembly Disassembly/Reassembly . 13-
Shift Fork Clearance Inspection . 13-
Shift Fork Disassembly/Reassembly . 13-
Mainshaft Assembly Clearance Inspection . 13- ..........
.............. ...........
.......... .....
......... ......
.........................
............................ ........................
........................
.......................... .....
........................ ..........
.............. ...........
.......... .....
......... ......
.........................
............................ ........................
........................
.......................... .....
........................
Mainshaft Disassembly . 13-
Mainshaft Inspection . 13-
Mainshaft Reassembly . 13-
Countershaft Assembly
Clearance Inspection . 13-
Countershaft Disassembly . 13-
Countershaft Inspection . 13-
Countershaft Reassembly . 13-
Synchro Sleeve and Hub Inspection and
Reassembly . 13-
Synchro Ring and Gear Inspection . 13-
Mainshaft Bearing and Oil Seal Replacement . 13-
Countershaft Bearing Replacement . 13-
Mainshaft Thrust Clearance Adjustment . 13-
Transmission Reassembly . 13-
Gearshift Mechanism Replacement . 13-
...
..............
........................ .............
.......................... ...
..............
........................ .............
..........................
Component Location Index . 13-
Differential Carrier, Final Driven
Gear Replacement . 13-
Carrier Bearing Replacement . 13-
Oil Seal Replacement . 13-
Differential Thrust Clearance Adjustment . 13-
104
104
105
106
107
108 111
112
113
117
119
120
121
127
127
129
130
131
133
138
139
140
140
141
142
08/08/21 14:46:36 61SNR030_130_0071
ProCarManuals.com
DYNOMITE -2009-

µ









(#'

%)Ref. No. Tool Number Description Qty
13-70
Manual Transmission
Special Tools
07GAJ-PG20110
Catch Adapter 1
07GAJ-PG20130 Base Adapter 1
07JAD-PL90100 Oil Seal Driver, 65 mm 1
07NAD-P20A100 Oil Seal Driver Attachment 1
07736-A01000B Adjustable Bearing Puller, 20 40 mm 1
07746-0010300 Bearing Driver Attachment, 42 x 47 mm 1
07746-0030100 Inner Driver Handle, 40 mm 1
07746-0030300 Inner Bearing Driver Attachment, 30 mm 1
07749-0010000 Driver Handle, 15 x 135L 1
: Part of Mainshaft Inspection Tool Set, 07GAJ-PG 20102.
: Must be used with commercially available 3/8’’-16 UNF Slide Hammer.
08/08/21 14:46:37 61SNR030_130_0072
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'

)
13-79
Manual Transmission
Component Location Index
GEARSHIFT MECHANISM
TRANSMISSION FLUID BACK-UP LIGHT SWITCH
TRANSMISSION
CHANGE LEVER ASSEMBLY COUNTERSHAFT ASSEMBLY
MAINSHAFT ASSEMBLY
SYNCHRO RING and GEAR SHIFT FORK
COUNTERSHAFT
CHANGE LEVER
SYNCHRO SLEEVE and HUB
REVERSE SHIFT FORK
DIFFERENTIAL
REVERSE IDLER GEAR
MAINSHAFT Replacement, page 13-138
Inspection and Replacement, page 13-82 Test, page 13-83
Removal, page 13-84
Installation, page 13-91
Disassembly, page 13-99
Reassembly, page 13-133
Disassembly/Reassembly, page 13-105 Clearance Inspection, page 13-117
Clearance Inspection, page 13-108
Inspection, page 13-127 Clearance Inspection, page 13-106
Disassembly/Reassembly, page 13-107
Disassembly, page 13-119
Inspection, page 13-120
Reassembly, page 13-121
Bearing Replacement,page 13-130
Clearance Inspection,
page 13-104
Inspection and Reassembly,page 13-127
Clearance Inspection,
page 13-104
Disassembly, page 13-111
Inspection, page 13-112
Reassembly, page 13-113
Bearing and Oil Seal Replacement, page 13-129
Thrust Clearance Adjustment, page 13-131
08/08/21 14:47:17 61SNR030_130_0081
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

!)
Exploded View - Clutch Housing
13-99
Transmission Disassembly
MAINSHAFT ASSEMBLY COUNTERSHAFT ASSEMBLY REVERSE IDLER GEAR BALL BEARING
REVERSE IDLER GEAR SHAFT
14x20mmDOWELPIN
MAGNET DIFFERENTIAL ASSEMBLY
OIL GUIDE PLATE C BEARING SET PLATE
NEEDLE BEARING
28 mm WASHER 28 mm SPRING WASHER
6 mm SPECIAL BOLT
REVERSE SHIFT FORK
SHIFT FORK ASSEMBLY
15 N·m (1.5 kgf·m, 11 lbf·ft)72 mm SNAP RING
6 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft)
35x58x8mmOILSEAL 28x43x7mmOILSEAL 20 mm WASHER BACK-UP LIGHT SWITCH
29N·m(3.0kgf·m,22lbf·ft)
20 mm BOLT
44N·m(4.5kgf·m,33lbf·ft) CLUTCH HOUSING
(cont’d)
Replace. Replace.Replace.
08/08/21 14:47:53 61SNR030_130_0101
ProCarManuals.com
DYNOMITE -2009-

Î
Exploded View - Transmission Housing
13-100Manual Transmission
Transmission Disassembly (cont’d)
TRANSMISSION HOUSING
32 mm SEALING CAP
34 N·m (3.5 kgf·m, 25 lbf·ft)
10 mm SEALING WASHER
FILLER PLUG
44 N·m (4.5 kgf·m, 33 lbf·ft)
40x56x8mmOILSEAL
10 mm FLANGE BOLT
44 N·m (4.5 kgf·m, 33 lbf·ft)
14 mm SEALING WASHER
TRANSMISSION HANGER A 8 mm FLANGE BOLT
27 N·m (2.8 kgf·m, 20 lbf·ft)
INTERLOCK BOLT
39 N·m (4.0 kgf·m, 29 lbf·ft)
OIL GUIDE PLATE M
72 mm SHIM
OIL GUTTER PLATE
DRAIN PLUG
39 N·m (4.0 kgf·m, 29 lbf·ft) 20 mm SEALING WASHER STEEL BALL SPRING
TRANSMISSION HANGER B DETENT BOLT
22 N·m (2.2 kgf·m, 16 lbf·ft)
12 mm SEALING WASHER
HARNESS BRACKET A
6 x 30 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft) 8x14mmDOWELPIN
CHANGE LEVER ASSEMBLY TRANSMISSION HANGER
10 mm FLANGE BOLT
44 N·m (4.5 kgf·m, 33 lbf·ft)
6 x 20 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft) 6 mm FLANGE BOLT
12 N·m (1.2 kgf·m, 9 lbf·ft) OUTPUT SHAFT (COUNTERSHAFT)
SPEED SENSOR
O-RING
80 mm SHIM Replace.
Replace.
Replace. Replace. Replace.Replace.
08/08/21 14:47:54 61SNR030_130_0102
ProCarManuals.com
DYNOMITE -2009-