2006 ACURA CSX tow





(#'
 )
11-329
Fuel Line/Quick-Connect Fitting Removal
A
AA
A AA
A B
D
C
NOTE: Before you work on the fuel lines and fittings,
read the Fuel Line/Quick-Connect Fitting Precautions
(see page 11-328).
1. Relieve the fuel pressure (see page 11-322).
2. Check the fuel quick-connect fittings (A) for dirt, and clean them if needed.
3. Place a rag or shop towel over the quick-connectfitting. Hold the connector (A) with one hand, and
squeeze the retainer tabs (B) with the other hand to
release them from the locking tabs (C). Pull the
connector off.
NOTE: Be careful not to damage the line (D) or other parts.
 Do not use tools.
 If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push
the connector until it comes off easily.
 Do not remove the retainer from the line; once removed, the retainer must be replaced with a
new one.
(cont’d)
* : This illustration shows K20Z2 engine.
08/08/21 14:29:53 61SNR030_110_0329
ProCarManuals.com
DYNOMITE -2009-


(#'
!) µ

(#') Special Tools Required
11-34411-344 Intake Air System
Throttle Body Cleaning
Intake Air Bypass Control Thermal
Valve Test
A A A
B
Do not insert your fingers into the installed throttle
body when you turn the ignition switch to ON (II) or
while the ignition switch is ON (II). If you do, you
will seriously injure your fingers if the throttle valve
is activated.
1. Check for damage to the air cleaner. If the air cleaner element is damaged, replace it (see page
11-346).
2. Remove the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine (see page 11-349).
3. Clean off the carbon from the throttle valve and inside the throttle body with a paper towel soaked
in throttle plate and induction cleaner.
NOTE: Remove the throttle body to clean it.
 Be careful not to pinch your fingers.
 To avoid removing the molybdenum coating, do not clean the bearing area of the throttle shaft (A).
 Do not spray throttle plate and induction cleaner directly on the throttle body.
 Use Honda genuine throttle plate and induction cleaner.
4. Install the throttle body (see page 11- 348).
5. Reset the ECM/PCM with the HDS (see page 11-4).
6. Turn the ignition switch to ON (II), and wait 2 seconds.
7. Do the ECM/PCM idle learn procedure (see page 11-310). Vacuum pump/gauge, 0 30 in.Hg, Snap-on YA4000A
or equivalent, commercially available
1. Start the engine, then let it idle. NOTE: The engine coolant temperature must be
below 65 °C (149 °F).
2. Remove the engine cover (see step 1 on page 9-3).
3. Remove the vacuum hose (A) from the intake air duct, and connect a vacuum pump/gauge (B) to the
hose.
4. Raise and lower the engine speed, and make sure the vacuum gauge reading changes as the engine
speed changes.
If the vacuum reading does not change, check for
these problems:
 Misrouted, leaking, broken, or clogged intake air bypass control system vacuum lines.
 A cracked or damaged intake air bypass control thermal valve. Replace the valve if needed
(see page 11-351).
5. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in neutral) until the radiator fan
comes on, then let it idle.
* : This illustration shows K20Z2 engine.
08/08/21 14:31:08 61SNR030_110_0344
ProCarManuals.com
DYNOMITE -2009-


Î


µ
µ µ
µ
12-12Clutch
Clutch Master Cylinder Replacement (cont’d)
C
DB
A
E
F
(P/N 08C30-B0234M)D
E
B C
A A
UP
13mm
(0.04 0.12 in.) 13mm
(0.04 0.12 in.) LEFT
SIDE
B
C
B
A
11. Remove the reservoir hose (A), then remove the
retaining clip (B) for disconnecting the clutch line
(C) from the clutch master cylinder (D). Plug or
wrap the end of the reservoir hose and the clutch
line with a clean shop towel to prevent brake fluid
from coming out.
NOTE: Inspect the hose. If the hose has damage,
leaks, interference, or twisting, replace it.
12. Remove the O-ring (E) and the clutch master cylinder seal (F) from the clutch master cylinder.
13. Install a new O-ring (A) on the clutch line (B), then apply silicone grease (P/N 08C30-B0234M) to the
end of the clutch line. Install the clutch line in the
clutch master cylinder (C) with a new retaining clip
(D).
NOTE: Make sure not to get any silicone grease on
the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves.
14. Install the reservoir hose (E). 15. Make sure the hose clamps (A) are positioned on
the master cylinder (B) and the reservoir (C) as
shown.
16. To prevent the retaining clip (A) from coming off, pry apart the tip (B) of the clip with a screwdriver.
Replace.
Replace.
08/08/21 14:42:33 61SNR030_120_0014
ProCarManuals.com
DYNOMITE -2009-

Î
 
Î
(#'



 )
5-speed Manual Transmission
12-14 Clutch
Slave Cylinder Replacement
B
A
B C
A A
B
DC
(P/N 08798-9002)
(P/N 08C30-B0234M)
A
B (P/N 08798-9002)
C D
E
22 N·m
(2.2 kgf·m, 16 lbf·ft)
NOTE:
 Use fender covers to avoid damaging painted surfaces.
 Do not spill brake fluid on the vehicle; it may damage the paint or plastic. If brake fluid does contact the
paint or plastic, wash it off immediately with water.
 Make sure not to get any silicone grease on the terminal part of the connectors and switches,
especially if you have silicone grease on your hands
or gloves.
1. Remove the clutch line bracket (A) and the slave cylinder (B).
2. Remove the roll pins (A). Disconnect the clutch line (B), and remove the O-ring (C). Plug or wrap the
end of the clutch line with a clean shop towel to
prevent brake fluid from coming out. 3. Install a new O-ring (A) on the clutch line (B), then
connect the clutch line to the slave cylinder (C).
4. Set in new roll pins (D) to the slave cylinder.
5. Pull back the boot (A), and apply s ilicone grease
(P/N 08C30-B0234M) to the boot and the slave
cylinder pushrod (B). Reinstall the boot.
6. Apply a light coat of super high temp urea grease (P/N 08798-9002) to the pushrod of the slave
cylinder (C) and the release fork (D).
7. Install the slave cylinder and the clutch line bracket (E).
Replace.
Replace.
08/08/21 14:42:34 61SNR030_120_0016
ProCarManuals.com
DYNOMITE -2009-

Î

(#'



 )
6-speed Manual Transmission
12-1512-15
A
B
A CB
8. Do the clutch hydraulic system bleeding (see page12-7).
9. Check the clutch operation and check for leaks.
10. Test-drive the vehicle. NOTE:
 Use fender covers to avoid damaging painted surfaces.
 Do not spill brake fluid on the vehicle; it may damage the paint or plastic. If brake fluid does contact the
paint or plastic, wash it off immediately with water.
 Make sure not to get any silicone grease on the terminal part of the connectors and switches,
especially if you have silicone grease on your hands
or gloves.
1. Remove the clutch line bracket (A) and the slave cylinder (B).
2. Remove the roll pins (A). Disconnect the clutch line (B), and remove the O-ring (C). Plug or wrap the
end of the clutch line with a clean shop towel to
prevent brake fluid from coming out.
(cont’d)
08/08/21 14:42:35 61SNR030_120_0017
ProCarManuals.com
DYNOMITE -2009-

Î

(#'



 )
6-speed Manual Transmission
12-1512-15
A
B
A CB
8. Do the clutch hydraulic system bleeding (see page12-7).
9. Check the clutch operation and check for leaks.
10. Test-drive the vehicle. NOTE:
 Use fender covers to avoid damaging painted surfaces.
 Do not spill brake fluid on the vehicle; it may damage the paint or plastic. If brake fluid does contact the
paint or plastic, wash it off immediately with water.
 Make sure not to get any silicone grease on the terminal part of the connectors and switches,
especially if you have silicone grease on your hands
or gloves.
1. Remove the clutch line bracket (A) and the slave cylinder (B).
2. Remove the roll pins (A). Disconnect the clutch line (B), and remove the O-ring (C). Plug or wrap the
end of the clutch line with a clean shop towel to
prevent brake fluid from coming out.
(cont’d)
08/08/21 14:42:35 61SNR030_120_0017
ProCarManuals.com
DYNOMITE -2009-


(#'

")
13-28Manual Transmission
Change Lever Assembly Disassembly/Reassembly
BREATHER CAP
6x1.0mm
12 N·m
(1.2 kgf·m, 9 lbf·ft)
ROLLER
WASHER
5TH SELECT
SPRING
SELECT STOP
PLATE SHIFT ARM
COVER
INTERLOCK REVERSE LOCK CAM
STRIKER8 mm SPRING WASHER
8mmSPECIALBOLT
31 N·m
(3.2 kgf·m, 23 lbf·ft)
DUST COVER CHANGE LEVER
CHANGE LEVER COVER
SELECT LEVER
DUST SEAL
1ST/2ND SELECT
SPRING SHIFT ARM
OIL SEAL
(P/N 08798-9002)
(P/N 08798-9002)
(P/N 08798-9002)
NOTE: Prior to reassembling, clean all the parts in solvent, dry them, and apply grease to the contact surfaces as
shown.
Turn toward the front of
the vehicle, then install it. Be careful not to damage the
dust seal when installing it.
Replace.
Replace.
08/08/21 14:45:01 61SNR030_130_0030
ProCarManuals.com
DYNOMITE -2009-



(#'
")
Special Tools Required
13-54
Manual Transmission
Mainshaft Thrust Clearance Adjustment
A
M B
B
A
C C
A
07GAJ-PG20110
B
07GAJ-PG20130 D
 Catch adapter 07GAJ-PG20110
 Base adapter 07GAJ-PG20130
NOTE:
 Take measurement at normal room temperature.
 Clean all the parts thoroughly before installation.
1. Remove the 72 mm shim (A) and oil guide plate M from the transmission housing (B).
2. Thoroughly clean the 28 mm spring washer (A) and the 28 mm washer (B) before installing them on the
clutch housings side ball bearing (C).
NOTE: Install the spring washer in the direction
shown.
3. Assemble all of the mainshaft components. NOTE: Refer to the Exploded View, as needed,
during the assembly (see page 13-36). 4. Install the mainshaft assembly into the clutch
housing.
5. Place the transmission housing over the mainshaft and onto the clutch housing.
6. Tighten the clutch and transmission housings with several 8 mm bolts.
NOTE: It is not necessary to use sealing agent
between the housing for this procedure.
7. Lightly tap on the mainshaft with a plastic hammer.
8. Attach the catch adapter (A) and the base adapter (B) to the mainshaft as follows:
 Back out the catch adapter bolt (C), and loosen the two hex bolts (D).
 Fit the catch adapter over the mainshaft so its lip is towards the transmission.
 Align the catch adapter lip around the groove at the inside of the mainshaft splines, then tighten
the hex bolts.
9. Fully seat the mainshaft by tapping its end with a plastic hammer.
10. Thread the catch adapter bolt in until it just contacts thewidesurfaceofthebaseadapter.
08/08/21 14:45:50 61SNR030_130_0056
ProCarManuals.com
DYNOMITE -2009-