2006 ACURA CSX turn signal


Î
(#' 
'

)
µ
µ
µ
µ
µ
µ µ
µ
DTC 81-61, 85-61:
DTC 81-62, 85-62:
YES
NO
YES
NO
YES
NO YES
NO
24-147
A
ODS UNIT HARNESS 18P CONNECTOR GRN
No Signal From the ODS
Unit
Non-stipulated Data From
the ODS Unit
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13), General Troubleshooting Information (see page
24-22), and Battery Terminal Disconnection and
Reconnection (see page 22-68).
1. Make sure nothing is on the front passenger’s seat.
2. Clear the DTC memory (see page 24-23).
3. Read the DTC (see page 24-22).
Go to step 4.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.
4. Check the connection between the ODS unit harness 18P connector and the ODS unit.
Go to step 6.
Repair the poor connection, clear the DTC,
and retest. If DTC 85-61 or 85-62 is still present, go
to step 5.
5. Turn the ignition switch to LOCK (0).
6. Check the No. 9 (7.5 A) fuse in the under-dash fuse/ relay box.
Go to step 7.
Replace the fuse, then turn the ignition switch
to ON (II). If the fuse blows again, check for a short
in the No. 9 (7.5 A) fuse circuit (floor wire harness,
front passenger’s seat wire harness (with seat
heater), or ODS unit harness). 7. Disconnect the ODS unit harness 18P connector (A)
from the ODS unit.
8. Turn the ignition switch to ON (II).
9. Measure the voltage between ODS unit harness 18P connector terminal No. 1 and body ground.
There should be battery voltage.
Go to step 10.
Open in the floor wire harness, front
passenger’s seat wire harness (with seat heater) or
ODS unit harness; replace the faulty harness, then
clear the DTC.
(cont’d)
Wire side of female terminals
Is DT C 81-61, 85-61, 81-62, or 85-62 indicated?I s t he connect i on OK ?
IsthefuseOK? Is there battery voltage?
08/08/21 13:59:47 61SNR030_240_0147
ProCarManuals.com
DYNOMITE -2009-



(#' 
'
)
µ
µ
µ
µ µ
µ
DTC 82-14:
YES
NO
YES
NO YES
NO
24-151
A
A
No Signal from the Front
Passenger’s Weight Sensor (front inner side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From the SRS INSPECTION menu on the HDS, select SWS DTC CHECK.
 DTC 14-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
 DTC 14-12: Go to step 4.
 DTC 14-13: Go to step 11.
 DTC 14-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (front
inner side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (front
inner side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
(cont’d)
Is DTC 82-14 indicated?I s anot her DT C al so i nd i cat ed ? Is DTC 14-12 indicated?
08/08/21 14:00:48 61SNR030_240_0151
ProCarManuals.com
DYNOMITE -2009-



(#' 
'
)
µ
µ
µ
µ µ
µ
DTC 82-16:
YES
NO
YES
NO YES
NO
24-156SRS
DTC Troubleshooting (cont’d)
A
A
No Signal from the Front
Passenger’s Weight Sensor (rear inner side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From INSPECTION the SRS menu on the HDS, select SWS DTC CHECK.
 DTC 16-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
 DTC 16-12: Go to step 4.
 DTC 16-13: Go to step 11.
 DTC 16-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (rear
inner side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (rear
inner side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
Is DTC 82-16 indicated?
I s anot her DT C al so i nd i cat ed ? Is DTC 16-12 indicated?
08/08/21 14:00:50 61SNR030_240_0156
ProCarManuals.com
DYNOMITE -2009-



(#' 
')
µ
µ
µ
µ µ
µ
DTC 83-26:
YES
NO
YES
NO YES
NO
24-163
A
A
No Signal from the Front
Passenger’s Weight Sensor (rear outer side)
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Read the DTC (see page 24-22).
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
3. From INSPECTION menu on the HDS, select SWS DTC CHECK.
 DTC 26-11: Short to power in the ODS unit harness; replace the ODS unit harness, then clear
the DTC.
 DTC 26-12: Go to step 4.
 DTC 26-13: Go to step 11.
 DTC 26-14: Go to step 19.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24).
4. Turn the ignition switch to LOCK (0). 5. Disconnect the ODS unit harness 3P connector (A)
from the front passenger’s weight sensor (rear
outer side).
6. Read the DTC. Go to step 7.
Faulty front passenger’s weight sensor (rear
outer side); replace the front passenger’s seat slide
assembly including all four front passenger’s
weight sensors (see page 24-207), then clear the
DTC.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the ODS unit harness 18P connector (A) from the ODS unit.
(cont’d)
Is DTC 83-26 indicated?I s anot her DT C al so i nd i cat ed ? Is DTC 26-12 indicated?
08/08/21 14:00:53 61SNR030_240_0163
ProCarManuals.com
DYNOMITE -2009-



(#' 
'
-)
µ
µ µ
µ
µ
µ
µ
µ
YES
NO Special Tools Required
YES
NO
YES
NO
YES
NO
DTC B2-1x:
24-17424-174SRS
DTC Troubleshooting (cont’d)
J
SRS UNIT CONNECTOR A (28P)
UNDER-DASH
FUSE/RELAY BOX
CONNECTOR J (4P)
6. Turn the ignition switch to LOCK (0).
7. Disconnect under-dash fuse/relay box connector J
(4P).
8. Measure the resistance between SRS unit connector A (28P) terminal No. 18 and under-dash
fuse/relay box connector J (4P) terminal No. 1.
There should be less than 1.0 .
Open in the under-dash fuse/relay box or
poor contact between connector J (4P) and the
under-dash fuse/relay box; check the connection. If
the connection is OK, replace the under-dash fuse/
relay box (see page 22-66), then clear the DTC.
Open in the dashboard wire harness; replace
the dashboard wire harness, then clear the DTC.  SRS inflator simulator 07SAZ-TB4011A
 SRS simulator lead L 070AZ-SNA0300
NOTE: Before doing this troubleshooting procedure,
review SRS Precautions and Procedures (see page
24-13) and General Troubleshooting Information
(see page 24-22).
1. Clear the DTC memory (see page 24-23).
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
3. Read the DTC (see page 24-22).
Go to step 4.
Go to step 5.
4. Read the DTC (see page 24-22).
Faulty rear safing sensor; replace the rear
safing sensor (see page 24-206), then clear the
DTC.
Go to step 7.
5. Read the DTC (see page 24-22).
Go to step 6.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures
(see page 24-24). If another DTC is indicated,
troubleshoot the DTC.No Signal from the Rear Safing
Sensor
Wire side of female terminals
Is the resistance as specif ied? Does the SRS indicator stays on, and is DT C
B2-1x i nd i cat ed ?
Is DTC 45-11 also indicated?
Is DTC B2-1x (except B2-11) also indicated?
08/08/21 14:00:57 61SNR030_240_0174
ProCarManuals.com
DYNOMITE -2009-

(#' '
-)(#')µ
µ
µ
µ
DTC 15-3x:
DTC 17-3x:
DTC 25-3x:
DTC 27-3x: SRS indicator does not come on
YES
NO
YES
NO
24-18124-181
Symptom Troubleshooting
No Signal From the Front Inner
Side Front Passenger’s Weight Sensor
No Signal From the Rear Inner
Side Front Passenger’s Weight Sensor
No Signal From the Front Outer
Side Front Passenger’s Weight Sensor
No Signal From the Rear Outer
Side Front Passenger’s Weight Sensor
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 82-15, 82-17,
83-25, and 83-27 (see page 24-155). 1. Turn the ignition switch to LOCK (0), then wait for
10 seconds.
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Intermittent failure, system is OK at this
time.
Go to step 3.
3. Connect the HDS to the data link connector (DLC) (see page 24-22).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Do the gauge control module self-diagnostic function (see page 22-241).
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
Does the SRS indicators come on?
Does t he SRS i nd i cat or come on?
08/08/21 14:01:52 61SNR030_240_0181
ProCarManuals.com
DYNOMITE -2009-

(#' '
-)(#')µ
µ
µ
µ
DTC 15-3x:
DTC 17-3x:
DTC 25-3x:
DTC 27-3x: SRS indicator does not come on
YES
NO
YES
NO
24-18124-181
Symptom Troubleshooting
No Signal From the Front Inner
Side Front Passenger’s Weight Sensor
No Signal From the Rear Inner
Side Front Passenger’s Weight Sensor
No Signal From the Front Outer
Side Front Passenger’s Weight Sensor
No Signal From the Rear Outer
Side Front Passenger’s Weight Sensor
NOTE: Only read DTCs from the SRS menu, not from
the SWS menus unless instructed to check SWS DTCs.
SWS (ODS unit) DTCs are subcodes of SRS unit DTCs.
Only troubleshoot the corresponding SRS DTCs.
Do the troubleshooting for SRS unit DTC 82-15, 82-17,
83-25, and 83-27 (see page 24-155). 1. Turn the ignition switch to LOCK (0), then wait for
10 seconds.
2. Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds
and then goes off.
Intermittent failure, system is OK at this
time.
Go to step 3.
3. Connect the HDS to the data link connector (DLC) (see page 24-22).
4. Make sure the HDS communicates with the vehicle and the SRS unit. If it does not communicate,
troubleshoot the DLC circuit (see page 11-204).
5. Do the gauge control module self-diagnostic function (see page 22-241).
Faulty SRS unit; replace the SRS unit
(see page 24-203).
Faulty gauge control module (tach); replace
the gauge control module (tach) (see page 22-277).
Does the SRS indicators come on?
Does t he SRS i nd i cat or come on?
08/08/21 14:01:52 61SNR030_240_0181
ProCarManuals.com
DYNOMITE -2009-




Installation
24-201
A
B
C
D
A
B
CA
B
D C
B
A
8. Disconnect the dashboard wire harness 4Pconnector (A) from the cable reel 4P connector (B),
then disconnect the dashboard wire harness 20P
connector (C) from the cable reel (D).
9. Release the lock tab (A) under the cable reel connector with a 90 ° hook shaped tool (B). Slide
the tool below the cable reel connector just above
the lock tab. Release the lower lock tab (C), and
slide the cable reel off the column. 1. Before installing the steering wheel, align the front
wheels straight ahead.
2. If not already done, disconnect the negative cable from the battery, then wait at least 3 minutes
before starting work.
3. Set the turn signal canceling sleeve (A) so that the projections (B) are aligned vertically.
4. Carefully install the cable reel (A) on the steering column shaft. Then connect 20P connector (B) to
the cable reel, and connect the 4P connector (C) to
the dashboard wire harness 4P connector (D).
(cont’d)
08/08/21 14:02:00 61SNR030_240_0201
ProCarManuals.com
DYNOMITE -2009-