2006 ACURA CSX fuse box

(#'
)
Symptom Diagnostic procedure Also check for
4-44
Cruise Control
Symptom Troubleshooting Index




Cruise control cannot be
set
1.
2.
3.
4.Check for PGM-FI DTCs (see page 11-3).
Check the No. 3 (10 A) fuse in the under-dash fuse/relay
box.
Do the cruise control combination switch test (see page
4-49).
Do the cruise control input test (see page 4-47). Poor ground G101 (A/T
model) or G401 (M/T
model)
Cruise control can be set,
butthecruisemain
indicator does not come
on 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the gauge control module self-diagnostic function
procedure (see page 22-241).
Do the cruise control input test (see page 4-47).
Test the cruise control main switch signal input. Faulty gauge control
module (tach)
Cruise control can be set,
but the cruise control
indicator does not come
on 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the gauge control module self-diagnostic function
procedure (see page 22-241).
Do the cruise control input test (see page 4-47).
Test the cruise control indicator signal input. Faulty gauge control
module (tach)
Vehicle does not
accelerate accordingly
when the resume/accel
button is pressed 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the cruise control combination switch test (see page
4-49).
Do the cruise control input test (see page 4-47).
Test the cruise control resume/accel switch signal input. Open circuit, loose or
disconnected terminal:
ORN
Set speed does not
cancel when the brake
pedal is pressed 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the brake pedal position switch test (see page
22-181).
Do the cruise control input test (see page 4-47).
Test the brake pedal position switch signal input. Short to power on
the BRN wire
Faulty brake pedal
position switch
Set speed does not
cancel (engine rpm stays
high) when the clutch
pedal is pressed (M/T
model) 1.
2.
3.
Check for PGM-FI DTCs (see page 11-3).
Do the clutch pedal position switch test (see page 4-50).
Do the cruise control input test (see page 4-47).
Test the clutch pedal position switch signal input. Short to ground in
the LT BLU wire
Faulty clutch pedal
position switch
Set speed does not
cancel when the cruise
control main button is
pressed 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the cruise control combination switch test (see page
4-49).
Do the cruise control input test (see page 4-47).
Test the cruise control main switch signal input. Short to power on the
YEL wire
Set speed does not
cancel when the cancel
button is pressed 1.
2.
3.Check for PGM-FI DTCs (see page 11-3).
Do the cruise control combination switch test (see page
4-49).
Do the cruise control input test (see page 4-47).
Test the cruise control cancel switch signal input. Open circuit, loose or
disconnected
terminals: LT GRN or
ORN
08/08/21 14:10:49 61SNR030_040_0045
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
´
µ
4-46 Cruise Control
Circuit Diagram
(A/T model) 764 5 12
G504 11
3
LIGHTS
CRUISE CONTROL INDICATOR
C21
C20
C12
12 V
5V
C4
G401 3 2 C1
A20
3
2 4
1 (50 A) No. 2
No. 19 (15 A) No. 21 (15 A)
A8
A6
C43 B28 GRY
ORN
ECM/PCM A37
A36
BAT
IG1
A39
A40
C39
C3
A41
THROTTLE BODY
TP SENSOR
No. 3
(10 A)
CRUISE MAIN INDICATOR
DRIVER
GAUGE CONTROL MODULE (TACH)
No. 12
(15 A)
UNDER-HOOD FUSE/RELAY BOX
BATTERY
No. 1 (100 A)
CPU
IG1 HOT in
ON (II) and
START (III)
CABLE
REEL
CAN-
CEL RESUME/
ACCEL
CABLE
REEL
THROTTLE
ACTUATOR
BRAKE
PEDAL
POSITION
SWITCH MULTIPLEX
INTEGRATED
CONTROL UNIT
TRANSMISSION
RANGE SWITCH SET/
DECEL
CRUISE
CONTROL
MAIN
CRUISE CONTROL
DIMMING CIRCUIT
PGM-FI
MAIN
RELAY 1
ETCS
CONTROL
RELAY
UNDER-DASH
FUSE/RELAY
BOX HORN
SWITCH
CRUISE CONTROL
COMBINATION SWITCH
IGNITION
SWITCH
IG1ETCS
ETCSRLY
IGP
MRLY CANL
CANH
BKSWNC
BKSW
TPSB
TPSA
VCC3
ETCSM
NC ATPFWD SG3
ETCSM
CRMTCLS
D8
H1 F9 F6 F5 E1
3
6
19101114
OUTPUT SHAFT
(COUNTERSHAFT)
SPEED SENSOR CLUTCH
PEDAL
POSITION
SWITCH No. 14 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
YEL
WHT BLU
YEL
LT BLU
BLK LT GRN ORN RED
LT GRN BRN ORN GRN WHT WHT
YEL RED
5V
BLU/WHT LT BLU BLU/YEL BLU
BLU/RED
GRN/YEL GRN RED/BLK RED/BLU
BLK
WHT
D2
F5 42 31
32
41 1
10
679 8 2
21 18 C101
(M/T model) CANL CANH
19
08/08/21 14:10:50 61SNR030_040_0047
ProCarManuals.com
DYNOMITE -2009-

(#'
)Signal to be
tested Test condition Parameter: Desired
resultPossible cause if result is not obtained
4-47
Cruise Control Input Test
NOTE: Always make sure that you have the latest Honda Diagnostic System (HDS) software before doing the input
tests.
1. Connect the HDS to the data link connector (DLC) (see step 2 on page 11-3).
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it does not communicate, troubleshoot the DLC circuit (see page 11- 204).
4. Go to PGM-FI, and check for DTCs (see page 11-3).
5. Do the following tests while monitoring parameters in the PGM-FI DATA LIST with the HDS. NOTE: Intermittent failures are often caused by loose circuit connections. While monitoring cruise control inputs,
flex the circuit wires, and note if any of the test results change.

















Brake pedal
position
switch signal
Brake pedal pressed,
then released
CRUISE BRAKE SW
should indicate OFF
when the brake pedal is
pressed and ON when
the brake pedal is
released. Faulty brake pedal position switch
Blown No. 3 (10 A) fuse in the under-
dash fuse/relay box
An open in the wire between the ECM/
PCM and the brake pedal position switch
A wire shorted to ground between the
ECM/PCM and the brake pedal position
switch
Clutch pedal
position
switch signal
(M/T model) Clutch pedal pressed,
then released
SHIFT/CLUTCH SW
should indicate ON
when the clutch pedal
is pressed and OFF
when the clutch pedal
is released. Faulty clutch pedal position switch
An open in the wire between the ECM
and the clutch pedal position switch
A wire shorted to ground between the
ECM and the clutch pedal position
switch
Poor ground G401
Transmission
range switch
signal (A/T
model) Shift lever in D and S SHIFT/CLUTCH SW
should indicate ON in P,
R,andN,andOFFinD
and S. Faulty transmission range switch
An open in the wire between the PCM
and the transmission range switch
A wire shorted to ground between the
PCM and the transmission range switch
Poor ground G101
Cruise control
main switch
signal Cruise control main
switch pressed and
released CRUISE MASTER
(MAIN) SW should
indicate ON when the
cruise control main
buttonispressedand
OFF when the cruise
control main button is
released. Faulty cruise control combination switch
Faulty gauge control module (tach)
An open in the wire between the gauge
control module (tach) and the cruise
control combination switch
A wire shorted to ground between the
gauge control module (tach) and the
cruise control combination switch
Poor ground G504
(cont’d)
08/08/21 14:10:50 61SNR030_040_0048
ProCarManuals.com
DYNOMITE -2009-

ÌÏ

Î

(#'
 )
Special Tools Required
5-3
Engine Removal
C
A
B
B
AB
 Engine hanger adapter VSB02C000015
 Engine support hanger, A and Reds AAR-T 1256
 2006 Civic engine hanger VSB02C000025
 Front subframe adapter VSB02C000016
 Universal lifting eyelet 07AAK-SNAA120 : These special tools are available through Honda
Canada Inc. Technical Tools Department; FAX 866-398-8665/e-mail: ch_technicaltools ch.honda.
com
NOTE:  Use fender covers to avoid damaging painted surfaces.
 To avoid damaging the wire and terminals, unplug the wiring connectors carefully while holding the
connector portion.
 Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Secure the hood in the wide open position (support rod in the lower hole).
2. Relieve the fuel pressure (see page 11-322).
3. Do the battery removal procedure (see page 22-69).
4. Disconnect the vacuum hose and the breather pipe, then remove the intake air duct (see step 2 on page
9-3).
5. Remove the air cleaner assembly (see page 11-345).
6. Remove the under-cowl panel (see step 4 on page 20-164). 7. Disconnect the connector (A), and remove the
harness clamps (B), then remove the pipe (C).
8. Disconnect the battery cables (A) from the under- hood fuse/relay box.
9. Remove the harness clamp (B). (cont’d)
08/08/21 14:20:21 61SNR030_050_0003
ProCarManuals.com
DYNOMITE -2009-


Î 

5-4Engine Assembly
Engine Removal (cont’d)
A
B B
C A A
B
10. Remove the engine control module (ECM)/ powertrain control module (PCM) cover (A), then
remove the three bolts (B) securing the ECM/PCM.
11. Disconnect the ECM/PCM connectors (A) and the engine wire harness connector (B).
12. Remove the harness clamps (C). 13. Remove the under-hood fuse/relay box (A) from the
ECM/PCM bracket (B), then remove the ECM/PCM
bracket.
14. K20Z3 engine: Remove the engine cover.
08/08/21 14:20:22 61SNR030_050_0004
ProCarManuals.com
DYNOMITE -2009-


Î 

5-22Engine Assembly
Engine Installation (cont’d)
A
B
B A 6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) 6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C A
51. Connect the evaporative emission (EVAP) canisterhose (A) and the brake booster vacuum hose (B).
52. Install the engine control module (ECM)/powertrain control module (PCM) bracket (A), then install the
under-hood fuse/relay box (B) to the ECM/PCM
bracket. 53. K20Z3 engine: Install the engine cover.
54. Connect the ECM/PCM connectors (A) and the
engine wire harness connector (B).
55. Install the harness clamps (C).
08/08/21 14:21:00 61SNR030_050_0022
ProCarManuals.com
DYNOMITE -2009-

Î
 Î

5-23
B
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B A
B
C
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
56. Install the ECM/PCM (A), then install the ECM/PCM
cover (B).
57. Connect the battery cables (A) to the under-hood fuse/relay box.
58. Install the harness clamp (B). 59. Install the pipe (A).
60. Connect the connector (B), and install the harness
clamps (C).
61. Install the under cowl-panel (see step 4 on page 20-164).
62. Install the air cleaner assembly (see page 11-345).
63. Install the front wheels.
64. Do the battery installation procedure (see page 22-69).
65. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat this operation three times, then check
for fuel leakage at any point in the fuel line.
66. Refill the engine with engine oil (see step 4 on page 8-10).
(cont’d)
08/08/21 14:21:01 61SNR030_050_0023
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
5-295-29
Transmission Mount Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) A
22. Raise the vehicle on the lift.
23. M/T model: Tighten the front mount mounting bolt.
24. Install the splash shield (see step 40 on page 5-20).1. Loosen the upper torque rod mounting bolt (A).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the engine control module (ECM)/
powertrain control module (PCM) cover, then
remove the three bolts securing the ECM/PCM (see
step 10 on page 5-4).
4. Remove the under hood fuse/relay box from the ECM/PCM bracket, then remove the ECM/PCM
bracket(seestep13onpage5-4).
(cont’d)
08/08/21 14:21:04 61SNR030_050_0029
ProCarManuals.com
DYNOMITE -2009-