2006 ACURA CSX lock

Î
Î
(#'#
)
´
µ
µ
µ
µ µ
µ
µ
µ
No picture is displayed
YES
NO
YES
NO YES
NO
YES
NO
23-338Navigation System
Symptom Troubleshooting
NAVIGATION UNIT CONNECTOR A (24P)
BBACKUP(WHT)
NAVIGATION UNIT CONNECTOR A (24P) ACC RADIO (PUR)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft code.
1. Check the No. 23 (10 A) fuse in the under-hood fuse/relay box and the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box, and reinstall the fuse if
it is OK.
Go to step 2.
Replace the fuse and recheck.
2. Turn the ignition switch to ON (II).
3. Operate the radio and listen to the audio.
Go to step 4.
Refer to audio system troubleshooting.
4. Turn the ignition switch to LOCK (0).
5. Remove the navigation unit (see page 23-355). 6. Measure the voltage between navigation unit
connector A (24P) terminal No. 24 and body ground.
Go to step 7.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
7. Turn the ignition switch to ON (II).
8. Measure the voltage between navigation unit connector A (24P) terminal No. 14 and body ground.
Go to step 9.
Repair open in the wire between the under-
dash fuse/relay box and the navigation unit.
Wire side of female terminals
Wire side of female terminals
IsthefuseOK? Can y ou hear t he aud i o? Is there battery voltage?
Is there battery voltage?
08/08/21 14:17:50 61SNR030_230_0341
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

µ
µ
µ
µ
YES
NO
YES
NO
Navigation display buttons do not work or
respond properly
23-34023-340Navigation System
Symptom Troubleshooting (cont’d)
5. Turn the ignition switch to LOCK (0), then turn to
ON (II), and observe the navigation picture.
Check for sources of electrical noise, such as
poor battery connection, alternator, defective
battery, aftermarket accessories or cell phone, and
poor pin fits at the navigation unit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Always make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Always check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
1. Turn the ignition switch to ON (II).
2. Go into the Detail Information & Settings select Unit Check, and use Hard Key test under Unit Check
(see page 23-305).
The system is OK at this time.
Replace the navigation unit (see page 23-355).
Di d t he i mage i mpr ov e?
Does t he nav i gat i on uni t but t ons w or k pr oper l y ?
08/08/21 14:17:50 61SNR030_230_0343
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
GPS icon is white or not shown Voice guidance cannot be heard, is broken
up, or there is static
Diagnostic Test: Self-Diagnosis Mode
YES
NO
YES
NO Diagnostic Test: Self-Diagnosis Mode
YES
NO
YES
NO
YES
NO
23-34123-341
NOTE: Check the vehicle battery condition first.
 With good reception, the icon is normally green.
 Make sure the GPS antenna is plugged in.
 Check for any aftermarket accessories or metallic window tinting that may be interfering with the GPS
signal.
 Make sure the vehicle is parked outside, away from buildings.
 Refer to GPS Information (see page 23-312) for realtime satellite reception display.
1. Check for aftermarket metallic wi ndow tint on the
rear window and electronic aftermarket
accessories (possibly hidden) mounted near the
GPS antenna or the navigation unit.
Remove tint or the accessories, and
recheck.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Go into the Self-Diagnosis Mode, and use the System Links diagnostic (see page 23- 297) to check
the GPS antenna.
Check for a kinked, crushed, or disconnected
GPS antenna wire. If the icon is still red, replace the
GPS antenna (see page 23-358).
Check that nothing is blocking the GPS
antenna located under the package shelf and
recheck. Substitute a known-good GPS antenna,
and recheck.
 If the symptom is gone, replace the GPS antenna.
 If the symptom is still present, substitute a known-good navigation unit (see page 23- 355),
and recheck. If the symptom is gone, replace the
original navigation unit. NOTE:
 Check the vehicle battery condition first.
 Check the navigation volume level (see Owner’s Manual).
 Check the connectors for poor connections or loose terminals.
 If the Hard Error Code is stored, check the Hard Error Code troubleshooting first.
 Make sure that the correct DVD color and version are installed.
 Inspect the DVD for dirt or damage.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
1. Turn the ignition switch to ON (II).
2. Press the SET-UP button.
3. Check the volume and voice feedback setting for the navigation system in set-up.
Set the voice feedback to ON, and select an
audible level for the volume.
Go to step 4.
4. Check the audio system operation.
Go to step 5.
Troubleshoot audio system.
5. Select the Self-Diagnosis mode.
6. Check for error code to the Error History.
Refer to the Hard Error Code
troubleshooting.
Replace the navigation unit (see page 23-355).
Is there af termarket metallic window tint orel ect r oni c accessor i es?
Is the GPS Ant icon red? Is ei t her set t o OF F ?
Can y ou hear t he aud i o?
Is the Hard Error Code in stored?
08/08/21 14:17:50 61SNR030_230_0344
ProCarManuals.com
DYNOMITE -2009-

Î

(#'#
)
 µ
µ
µ
µ
µ
µ
Voice control does not work/respond
Diagnostic Test: Mic Level
YES
NO
YES
NO
YES
NO
23-342Navigation System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR D (12P)
NAVI GUIDE (GRN)
NOTE: Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the connector for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
 After troubleshooting, enter the anti-theft codes for the navigation system.
Before assuming that a voice complaint is hardware
related, ensure that the voice control system is being
operated correctly.  Make sure you are on the correct screen when trying to issue a voice command. For instance, the
command ‘‘Find the nearest Italian Restaurant’’ only
works on a Map screen.
(See the Navigation System Manual for a complete
list of allowed voice commands for the information
being displayed.)
 Close the windows, moonroof, and doors.
 Set the fan speed to low (1 or 2).
 Adjust the air flow from the air conditioning vents so that they do not blow against the microphone on the
ceiling.
 Pause after pressing the navigation TALK button, then give a voice command clearly in a natural
speaking voice. If the system cannot recognize your
command, speak louder.
 If the microphone picks up voices other than yours, the system may not interpret your voice commands
correctly.
 If you speak a command with something in your mouth, or your voice is too husky, the system may
misunderstand your command.
 Compare the system operation with a known-good vehicle. Have more than one person test the system
operation. If the like known-good vehicle performs
the same, if is a characteristic of the system. 1. Turn the ignition switch to ON (II).
2. Go into the Self-Diagnosis Mode select, Mic Icon
Menu, and use the Mic Level test under Functional
Setup (see page 23-309) to check the operation of
the navigation Talk and Back buttons.
step 10
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Do the voice control switch test (see page 23-357).
Go to step 5.
Replace the HFL-voice control switch.
5. Disconnect the HFL-voice control switch 5P connector and navigation unit connector D (12P).
6. Check for continuity between body ground and navigation unit connector D (12P) terminal No. 1.
Repair short to body ground in the wire
between the navigation unit and the voice control
switch, or replace the cable reel.
Go to step 7.
Wire side of female terminals
Ar e t he nav i gat i on T ALK and BACK but t onsoper at i onal ?
I s t he v oi ce cont r ol sw i t ch OK ?
Is there continuity?
08/08/21 14:17:51 61SNR030_230_0345
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
µ
µ µ
µ
µ
µ
Vehicle position icon constantly leaves road,
moves erratically, or is displayed very far
from actual vehicle position
YES
NO YES
NO
YES
NO
23-344Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Check that the GPS antenna is plugged in.
 This is not the same condition as when driving off- road (or on a fire or logging road). This condition is
caused by a loss of map matching from a bad sensor
input. Check for after market window tinting or other
objects that can block the GPS signal. Always do the
Map matching (see page 23-269) before proceeding
with the troubleshooting.
 Make sure that the correct DVD color and version are installed.
 Inspect the DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
 Check the GPS signal reception in an open area.
1. Check the GPS icon on the navigation screen.
Do the troubleshooting for GPS icon is white
or not shown (see page 23-341).
Go to step 2. 2. Go into the Self-Diagnosis Mode, and use the Yaw
Rate test (see page 23-314) to check the yaw rate
sensor.
3. Go into the Self-Diagnosis Mode, and use the Car Status test (see page 23-315) to check the vehicle
speed pulse.
The condition may be normal. Check to see if
the condition occurs in the same place in a known-
good vehicle. If it does, the problem could be in the
database.Gotostep4.
If the problem is the yaw rate sensor, replace
the navigation unit (see page 23-355). If the
problem is the vehicle speed pulse, check for an
open in the wire between the navigation unit and
the ECM/PCM (VSP signal). If the wire is OK,
substitute a known-good navigation unit, and retest.
If the problem goes away, replace the original
navigation unit. If the problem is still present,
replace the ECM/PCM.
4. Substitute a known-good navigation unit, and check to see if the problem occurs in the same
place.
The problem is in the database. Report the
problem according to the Navigation System
Manual under Reporting Errors.
Replace the original navigation unit (see page
23-355).
Is the GPS icon white? Ar e t he y aw r at e sensor and v ehi cl e speed pul se
OK ?
Does t he pr obl em occur i n t he same pl ace?
08/08/21 14:17:51 61SNR030_230_0347
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
µ
µ
µ
µ µ
µ
µ
µ
Vehicle icon wanders across the map when
driving (does not follow a displayed road) or
map or vehicle ICON spins
YES
NO
YES
NO YES
NO
YES
NO
23-345
NOTE:
 Check the vehicle battery condition first.
 This is not the same condition as when driving off-road (or on a fire or logging road).
 This condition is caused by a loss of map matching from a bad sensor input. Check for aftermarket or
other objects that can block the GPS signal. Always
perform Map matching (see page 23-269) before
proceeding with the troubleshooting.
 Always check for and resolve all CAN DTCs before troubleshooting the navigation system.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode, and use
Version (see page 23-316).
 Make sure that the correct DVD color and version are installed.
 Check for aftermarket metallic window tinting.
 Inspect the DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Check the DVD for damage or scratches.
 Check for connectors for poor connections or loose terminals.
1. Check the GPS icon on the navigation screen.
Do the troubleshooting for GPS icon is white
or not shown (see page 23-341).
Go to step 2.
2. Go into the Self-Diagnostic mode, and use the Yaw Rate diagnosis (see page 23- 314) to check the yaw
rate sensor.
Go to step 3.
Replace the navigation unit (see page 23-355). 3. Go into the Diagnostic mode, and use the Car
Status diagnosis (see page 23-315) to check the
vehicle speed pulse (VSP) and the BACK signals.
The problem may be a characteristic of the
system. Check to see if the problem occurs in the
same place in a known-good vehicle. If it does, the
problem could be in the database. Go to step 4.
 If the problem is the vehicle speed pulse, troubleshoot the vehicle speed signal circuit. BLU
wire for open or short. If OK, good ECM/PCM. If
the problem or symptom goes Update the ECM/
PCM (see page 11-227) if it does not have the
latest software or substitute a known-good ECM/
PCM (see page 11-228).
 If the BACK signal is indicated ON (I), when in any shift lever position other than reverse,
troubleshoot the back-up light switch circuit or
MICU (A/T).
4. Substitute a known-good navigation unit (see page 23-355), and check to see if the problem occurs in
thesameplace.
The problem is in the database and should
be considered a characteristic of the system.
Report the problem according to the Navigation
System Owner’s Manual under Reporting Errors
and look for improvements in future databases.
Replace the navigation unit (see page 23-355).
Is the GPS icon white or missing?
I s t he y aw r at e sensor OK ? Ar e t he v ehi cl e speed pul se and t he BACK si gnal s
OK ?
Does t he pr obl em occur i n t he same pl ace?
08/08/21 14:17:51 61SNR030_230_0348
ProCarManuals.com
DYNOMITE -2009-

´
(#'#
)

(#'#
)

µ
µ
µ
µ µ
µ
Display day/night mode does not work or
does not work properly System locks up or freezes constantly
YES
NO
YES
NO YES
NO
23-34823-348Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Check the connectors for poor connection or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
 Full brightness on the instrument panel brightness control with the head lights turned on causes the
system to stay in the day mode, even when the lights
are on.
1. Make sure the instrument panel brightness control is not on full brightness. Turn the headlights on,
and adjust the dash brightness to the middle range.
2. Change the day/night mode under Set-up to AUTO, and recheck.
The system is OK at this time.
Go to step 3.
3. Go into the Diagnostic Menu and use the Car Status test to check for an ILL signal (see page 23-315).
Replace the navigation unit (see page 23-355).
Check the ILL circuit between the
navigation unit and the No. 14 (7.5 A) fuse in the
under-dash fuse/relay box. NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Start the engine, and turn the ignition switch to LOCK (0), then turn the ignition switch to ON (II).
The system is OK at this time.
Check the DVD for scratches or damage, and
the navigation unit for water damage. If OK, go into
the Diagnostic Menu, and do all of the Unit Check
tests (see page 23-305). Also check for low battery
charge or poor charging system performance.
Does t he d i spl ay change t o d ay and ni ght mod es w hen t ur ni ng t he head l i ght s on and of f ?
I s t he I LL si gnal OK ? Does the system reboot?
08/08/21 14:17:52 61SNR030_230_0351
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-34923-349
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (24P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-316).
 Check for connectors for poor connections loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-297).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-341).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-355), and recheck.
Replace the navigation unit (see page 23-355).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:17:52 61SNR030_230_0352
ProCarManuals.com
DYNOMITE -2009-