2005 NISSAN X-TRAIL stop start

HARNESS
PG-67
C
D
E
F
G
H
I
J
L
MA
B
PG

NATS BL Nissan Anti-Theft System
NAVI AV Navigation System
NONDTC AT Non-Detective Items
OVRCSV AT Overrun Clutch Solenoid Valve
P/SCKT WW Power Socket
PGC/V EC EVAP Canister Purge Volume Control Solenoid Valve
PHASE EC Camshaft Position Sensor (PHASE)
PHONE AV Telephone (Pre-wire)
PNP/SW AT Park/Neutral Position Switch
PNP/SW EC Park/Neutral Position Switch
PNPSW1 EC Park/Neutral Position Switch
POS EC Crankshaft Position Sensor (CKPS) (POS)
POWER PG Power Supply Routing
PRGVLV EC EVAP Canister Purge Volume Control Solenoid Valve
PRWIRE BL Theft Warning System (Pre-wire)
PS/SEN EC Power Steering Pressure Sensor
PST/SW EC Power Steering Oil Pressure Switch
R/FOG LT Rear Fog Lamp
ROOM/L LT Interior Room Lamp
RP/SEN EC Refrigerant Pressure Sensor
RRO2 EC Rear Heated Oxygen Sensor
RRO2/H EC Rear Heated Oxygen Sensor Heater
S/LOCK BL Power Door Lock - Super Lock
S/SIG EC Start Signal
S/WARN SB Seat Belt Warning System
SEAT SE Power Seat
SEN/PW EC Sensor Power Supply
SHIFT AT A/T Shift Lock System
SROOF RF Sunroof
SRS SRS Supplemental Restraint System
SSV/A AT Shift Solenoid Valve A
SSV/B AT Shift Solenoid Valve B
START SC Starting System
STEP/L LT Step Lamp
STOP/L LT Stop Lamp
TAIL/L LT Parking, License and Tail Lamps
TCC/V EC Turbocharger Boost Control Solenoid Valve
TCCSV EC Turbocharger Boost Control Solenoid Valve
TCV AT Torque Converter Clutch Solenoid Valve
TPS AT Throttle Position Sensor
TPS1 EC Throttle Position Sensor (Sensor 1)
TPS2 EC Throttle Position Sensor (Sensor 2)
TPS3 EC Throttle Position Sensor
TURN LT Turn Signal and Hazard Warning LampCode Section Wiring Diagram Name

MA-26
ENGINE MAINTENANCE (QR20DE·QR25DE)

3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
INSPECTION AFTER INSTALLATION
1. Start engine, and make sure there is no leaks of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and adjust engine oil. Refer to MA-24, "
Changing Engine Oil" .
Checking and Changing Spark PlugsELS000ZK
REMOVAL
1. Remove ignition coil. Refer to EM-31, "IGNITION COIL" .
2. Remove spark plug with spark plug wrench (commercial service
tool).
CAUTION:
Do not drop or shock it.
INSPECTION AFTER REMOVAL (EXCEPT FOR RUSSIA)
Use standard type spark plug for normal condition.
Hot type spark plug is suitable when fouling occurs with standard type spark plug under conditions such as:

Frequent engine starts

Low ambient temperatures
Cold type spark plug is suitable when spark plug knock occurs with standard type spark plug under conditions
such as:

Extended highway driving

Frequent high engine revolution

Check plug gap of each spark plug.

If out of standard, adjust or replace spark plug.

Use a wire brush for cleaning, if necessary.Oil filter:
: 17.6 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
SEM294A
MakeNGK
Standard typeLFR5A-11
Hot typeLFR4A-11
Cold typeLFR6A-11
Standard :1.0 - 1.1 mm (0.039 - 0.043 in)
SMA476

ENGINE MAINTENANCE (YD22DDTI)
MA-35
C
D
E
F
G
H
I
J
K
MA
B
MA

INSTALLATION
Install in reverse order of removal, paying attention to following:

Replace O-ring on drain plug with new one.

Screw the fuel filter by hand until packing contacts sealing surface of bracket. Then tighten it by turning
approximately 2/3 turn.

After installation, bleed air from fuel path. Refer to FL-18, "Air Bleeding" .
INSPECTION AFTER INSTALLATION
Make sure there is no fuel leakage at connections in the following steps.

Start the engine and rev it up and check for fuel leaks at connections.
Changing Air Cleaner FilterELS000CG
VISCOUS PAPER TYPE
The viscous paper type air cleaner filter does not require any clean-
ing operation between renewal.
Changing Engine OilELS000CH
WARNING:

Be careful not to burn yourself, as the engine oil is hot.

Prolonged and repeated contact with used engine oil may cause skin cancer: try to avoid direct
skin contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand
cleaner as soon as possible.
1. Warm up engine, put vehicle horizontally and check for engine oil leakage from engine components.
2. Stop engine and wait for 10 minutes.
3. Loosen oil filter cap and then remove drain plug.
4. Drain engine oil.
5. Install drain plug with new washer. Refer to EM-157, "
OIL PAN
AND OIL STRAINER" .
CAUTION:
Be sure to clean drain plug and install with new washer.
6. Refill with new engine oil.
Engine oil specification and viscosity:
Refer to MA-17, "
RECOMMENDED FLUIDS AND LUBRI-
CANTS" .
Engine oil capacity (Approximate):
Unit: (lmp qt)
Fuel filter drain plug:
: 4.9 N·m (0.50 kg-m, 43 in-lb)
PBIC0526E
Oil pan drain plug:
: 34 N·m (3.5 kg-m, 25 ft-lb)
PBIC0527E
Drain and refill With oil filter change 5.2 (4-5/8)
Without oil filter change 4.9 (4-3/8)
Dry engine (Overhaul)6.3 (5-1/2)

MA-36
ENGINE MAINTENANCE (YD22DDTI)

CAUTION:

The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.

Always use the dipstick to the determine when the proper amount of engine oil is in the engine.
7. Warm up engine and check area around drain plug and oil filter for oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level.
Changing Oil Filter (TYPE A)ELS000CI
REMOVAL
1. Open oil filter installation/ removal cover on RH engine undercover.
2. Using the oil filter wrench, remove the oil filter.
CAUTION:

Be careful not to get burned when the engine and engine oil are hot.

When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.

Do not allow engine oil to adhere to the drive belts.

Completely wipe off any engine oil that adhere to the engine and the vehicle.

The oil filter is provided with a relief valve.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply engine oil to the oil seal circumference of the new oil filter.
3. Screw the oil filter manually until it touches the installation surface, then tighten it by 1/2 turn. Or tighten to
specification.
INSPECTION AFTER INSTALLATION
1. Start engine, and check there is no leak of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and add engine oil. Refer to MA-35, "
Changing Engine Oil" .
PBIC0249E
SMA010
Oil filter:
: 18 N·m (1.8 Kg-m, 13 ft-lb)

MA-38
ENGINE MAINTENANCE (YD22DDTI)

5. Remove O-ring from oil filter body.

Push O-ring in one direction, lift the slack part using fingers,
and remove O-ring from oil filter body.
CAUTION:
Do not use a screwdrivers etc. as they may cause dam-
age to oil filter body.
INSTALLATION
1. Completely remove all foreign objects adhering to the inside of oil filter body or O-ring mounting area
(body side and bracket side).
2. Install oil filter and O-ring to oil filter body.

Push oil filter into filter body completely.
3. Install oil filter body to oil filter bracket.
INSPECTION AFTER INSTALLATION
1. After warming up engine, check there is no leaks of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and add engine oil. Refer to MA-35, "
Changing Engine Oil" .
Draining WaterELS000CJ
1. Prepare a tray at the drain hose open end.
2. Loosen drain cock, and operate priming pump to drain water
from fuel filter.
CAUTION:

Water in filter is drained with fuel. Prepare larger capacity
pan than fuel filter volume.

Drained water is mixed with fuel. Prevent fuel from adher-
ing to rubber parts such as engine mount insulator.
3. After draining, close drain cock by hand.
CAUTION:
If drain cock is tightened excessively, it may be damaged
and fuel will leak. Do not use tools to tighten drain cock.
4. Bleed air in fuel piping. Refer to FL-18, "
Air Bleeding" .
5. Start engine and make sure there is no fuel leakage.
JLC292B
Oil filter body:
: 22 N·m (2.2 Kg-m, 16 ft-lb)
SBIA0138E

IDX-8
ALPHABETICAL INDEX
Spark plug(QR20DE-QR25DE) ........................ EM-32
Specification value ............................. EC-120, EC-620
Speedometer ........................................................ DI-4
Spiral cable ..................................................... SRS-33
SROOF - Wiring diagram ................................... RF-11
SRS - See Supplemental Restraint System ..... SRS-6
SRS - Wiring diagram/LHD ............................. SRS-11
SRS - Wiring diagram/RHD ............................ SRS-13
SRS Trouble diagnoses .................................... SRS-8
Stall test (A/T) ...................................... AT-65, AT-257
Standardized relay ............................................. PG-77
START - Wiring diagram ........................ SC-24, SC-25
Start signal ..................................... EC-1345, EC-1696
Starter ................................................................ SC-23
Starting system .................................................. SC-23
Steering gear and linkage inspection ................ MA-45
Steering knuckle ................................................ FAX-7
Steering linkage ................................................. PS-16
Steering wheel and column ..................... PS-8, PS-11
Steering wheel turning force ................................ PS-8
Stop lamp .............................................. LT-98, LT-118
Stop lamp switch ................................ EC-405, EC-809
STOP/L - Wiring diagram ...................... LT-98, LT-118
Suction control valve .... EC-1231, EC-1275, EC-1280,
EC-1570
, EC-1614, EC-1619
Sunload sensor ............. ATC-114, ATC-116, ATC-123
Sunroof .............................................................. RF-10
Super lock .......................................................... BL-42
Supplemental Restraint System ....................... SRS-6
Supplemental restraint system - Wiring diagram/LHD ..
SRS-11
Supplemental restraint system - Wiring diagram/RHD .
SRS-13
Suspension ....................................................... MA-46
Symbols and abbreviations ........................ GI-9, GI-22
Symptom matrix chart .......................... EC-84, EC-584
Synchronizer (M/T) ............................... MT-23, MT-41
System readiness test (SRT) code .................... EC-56
T
Tachometer ........................................................... DI-4
Tail lamp ............................................. LT-103, LT-116
TAIL/L - Wiring diagram ...................... LT-103, LT-145
Tailgate lamp .................................................... LT-103
TC boost control solnoid valve ...... EC-1061, EC-1506,
EC-1659
TC boost sensor ............................................ EC-1151
TCC/V - Wiring diagram ................. EC-1062, EC-1660
TCM circuit diagram ........................................... AT-21
TCM inspection table ........................... AT-94, AT-286
THEFT - Wiring diagram .................................. BL-104
Thermal protector ............................................ ATC-95
Thermostat(QR20DE-QR25DE) ....................... CO-23
Thermostat(YD22DDTi) .................................... CO-46
Three way catalyst function ............................. EC-264
Three way catalyst precautions ............................ GI-5
Three way catalyst(QR20DE-QR25DE) ........... EM-25
Throttle control motor relay ................ EC-306, EC-737
Throttle position sensor (TPS) ......... EC-171, EC-231,
EC-368
, EC-370, EC-424, EC-658, EC-680, EC-771,
EC-773
, EC-830
Throwout bearing - See Clutch release bearing CL-14
Time control system .......................................... BCS-3
Timing chain(QR20DE-QR25DE) ..................... EM-46
Timing chain(YD22DDTi) .................. EM-193, EM-198
Torque converter installation ............. AT-415, AT-523
TPS1 - Wiring diagram ..................... EC-233, EC-682
TPS2 - Wiring diagram ..................... EC-173, EC-660
TPS3 - Wiring diagram ..................... EC-426, EC-832
Transmission case (M/T) ...................... MT-22, MT-40
Trouble diagnoses .............................................. GI-10
Turbocharger charge air cooler(YD22DDTi) ... EM-144
Turbocharger precautions ..................................... GI-6
Turbocharger(YD22DDTi) ............................... EM-151
TURN - Wiring diagram .......................... LT-87, LT-89
Turn signal lamp ................................... LT-87, LT-118
Two trip detection logic ....................... EC-52, EC-565
V
Vacuum hose (brake system) ............................ BR-25
Vacuum hose drawing (Engine control) EC-32, EC-545
Vacuum pump(YD22DDTi) ............................. EM-163
Valve clearance(QR20DE-QR25DE) ................ EM-64
Valve clearance(YD22DDTi) ........................... EM-185
Valve guide ....................................................... EM-77
Valve guide(QR20DE-QR25DE) ....................... EM-77
Valve lifter(QR20DE-QR25DE) ......................... EM-56
Valve lifter(YD22DDTi) ................................... EM-183
Valve seat(QR20DE-QR25DE) ......................... EM-79
Valve seat(YD22DDTi) ................................... EM-219
Valve spring(QR20DE-QR25DE) ...................... EM-80
Variable induction air control system (VIAS) ... EC-457,
EC-897
Vehicle speed sensor (VSS) EC-276, EC-403, EC-709,
EC-807
VIAS - Wiring diagram ...................... EC-459, EC-899
W
WARN - Wiring diagram .......................... DI-36
, DI-44
Warning chime .................................................... DI-56
Warning lamps .................................................... DI-35
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-14
Water control valve(QR20DE-QR25DE) ........... CO-23
Water pump(QR20DE-QR25DE) ...................... CO-21
Water pump(YD22DDTi) ................................... CO-43
Water temperature gauge ..................................... DI-4
Weatherstrip - See Exterior ............................... BL-21
Wheel alignment (front) .................................... FSU-6
Wheel alignment (rear) ..................................... RSU-6
Wheel balance ....................................... WT-4, MA-43
Wheel bearing (rear) ........................... RAX-6, RAX-10
Wheel hub (front) ............................................... FAX-7
Wheel hub (rear) ............................................. RAX-10
Wheel sensors (ABS) ..................................... BRC-46