2005 MITSUBISHI 380 belt

REAR SEAT CUSHION TRIM COVER
INTERIOR52A-47
REAR SEAT CUSHION TRIM FITMENT
.
1. Locate the new trim onto the pad by aligning the Velcro strip
with the grooves. Use an intersection in order toalign both
directions. Whenever possible work from the centre of the
trim toward the outside.
2. Pull the cover around the sides of the pad.
3. Pull trim through the seat belt slots as shown and attach to
wires

FRONT SEAT BELT
INTERIOR52A-58
FRONT SEAT BELT
REMOVAL AND INSTALLATIONM1523001300370
SRS: Before removing and installing the seat belts with pre-tensioner, refer to GROUP 52B, Seat
Belt with Pre-tensioner P.52B-250.
NOTE:
*If so equipped
Pre-removal and Post-installation Operation
Turn the ignition key to the LOCK (OFF) position.
Disconnect the negative battery terminal.Post-installation Operation
Adjustment Procedures of Special Function (refer to GROUP
52B, On-Vehicle Service P.52B-250.)
1. EXTENDER SEAT BELT
ASSEMBLY*
OUTER SEAT BELT REMOVAL
STEPS
2. SASH GUIDE COVER
CENTER PILLAR TRIM LOWER
(REFER TO P.52A-11.)
3. OUTER SEAT BELT (REFER TO
GROUP 52B, SEAT BELTS WITH
PRE-TENSIONER P.52B-250.)4. CENTER PILLAR TRIM UPPER
(REFER TO P.52A-11.)
5. ADJUSTABLE SEAT BELT ANCOR
INNER SEAT BELT
6. SEAT BELT SWITCH
CONNECTOR
SHIELD COVER (REFER TO
P.52A-33.)
7. INNER SEAT BELTOUTER SEAT BELT REMOVAL
STEPS (Continued)

REAR SEAT BELT
INTERIOR52A-59
INSPECTIONM1523004400116.
SEAT BELT SWITCH CONTINUITY CHECK
REAR SEAT BELT
REMOVAL AND INSTALLATIONM1523001600371
ITEM TESTER
CONNECTIONSPECIFIED
CONDITION
Fastened seat belt 1
2 Open circuit
Unfastened seat belt 1
2 Less than 2 ohms
REMOVAL STEPS
REAR SEAT CUSHION
ASSEMBLY (REFER TO
P.52A-55.)
1. INNER SEAT BELT
2. CENTER SEAT BELT INNERREAR SHELF TRIM (REFER TO
P.52A-11.)
3. OUTER SEAT BELT
4. CENTER SEAT BELT OUTERREMOVAL STEPS (Continued)

SPECIFICATIONS
INTERIOR52A-60
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONSM1521004100227
ITEM SPECIFICATION
FRONT SEAT
Front seatback assembly bolt 44
10 Nm (33 7 ft-lb)
Front seat cushion assembly bolt 12
2 Nm (102 22 in-lb)
Front seat bolt 44
10 Nm (33 7 ft-lb)
Front seat nut 30
5 Nm (22 4 ft-lb)
REAR SEAT
Seatback assembly bolt 22
4 Nm (16 3 ft-lb)
FRONT SEAT BELT
Adjustable seat belt anchor bolt 44
10 Nm (33 7 ft-lb)
Inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Outer seat belt bolt 44
10 Nm (33 7 ft-lb)
REAR SEAT BELT
Center seat belt outer and inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Inner seat belt bolt 44
10 Nm (33 7 ft-lb)
Seat belt shoulder anchor bolt 44
10 Nm (33 7 ft-lb)
Seat belt lower anchor bolt 44
10 Nm (33 7 ft-lb)

FLOOR, SEAT AND ROOF
CONFIGURATION DIAGRAMS80-17
FLOOR, SEAT AND ROOFM1801000900930
D-01 (2) VANITY MIRROR LIGHT (RH)
D-02 (4) MAP LIGHT ASSEMBLY SUNROOF>
D-03 (7) OVERHEAD CONSOLE ASSEMBLY

D-04 (10) SUNROOF ASSEMBLY
D-05 (2) VANITY MIRROR LIGHT (LH)
D-06 (3) REAR DOOR SWITCH (RH)
D-07 (3) REAR DOME LIGHT
D-09 (2) REAR SPEAKER (RH)
D-10 (2) TRUNK LAMP
D-11 (1) DEFOGGER (CHOKE COIL)
D-12 (2) REAR SPEAKER (LH)
D-13 (1-B) PARKING BRAKE SWITCHD-14 (6) A/T SHIFT SWITCH AND SELECT
POSITION ILLUMINATION LIGHT
D-15 (2) SUB WIRING HARNESS FOR
ACCESSORY SOCKET (2)
D-16 (3) REAR DOOR SWITCH (LH)
D-17 (2) FUEL LEVEL SENSOR (SUB)
D-18 (5-GR) FUEL PUMP MODULE
D-19 (10) FLOOR WIRING HARNESS AND
REAR DOOR WIRING HARNESS
(LH) COMBINATION
D-20 (2) SIDE IMPACT SENSOR (LH)
D-21 (2-B) SEAT BELT PRETENSIONER (LH)
D-22 (3) FRONT DOOR SWITCH (LH)
D-24 (2-R) SIDE AIR BAG MODULE (SQUIB)
(LH)