2005 MITSUBISHI 380 relay

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-156
STEP 7. Check the ground circuit to the power window
relay. Measure the resistance at power window relay
connector C-203.
(1) Disconnect power window relay connector C-203 and
measure the resistance available at the junction block side
of the connector.
(2) Measure the resistance value between terminal 3 and
ground.
The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 9.
NO : Go to Step 8.
STEP 8. Check the wiring harness between power window
relay connector C-203 (terminal 3) and ground.
NOTE: Also check junction block connector C-211 for loose,
corroded or damaged terminals, or terminals pushed back in
the connector. If junction block connector C-211 is damaged,
repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection P.00E-2.
Q: Is the wiring harness between power window relay
connector C-203 (terminal 3) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The power
windows function should now work normally.

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-160
STEP 14. Check the wiring harness between power
window relay connector C-203 (terminal 4) and power
window main switch connector E-04 (terminal 10).
NOTE: Also check junction block connector C-215 and inter-
mediate connectors C-12 for loose, corroded or damaged ter-
minals, or terminals pushed back in the connectors. If junction
block connector C-215 or intermediate connector C-12 is dam-
aged, repair or replace the damaged component(s) as
described in GROUP 00E, Harness Connector Inspection
P.00E-2.
Q: Is the wiring harness between power window relay
connector C-203 (terminal 4) and power window main
switch connector E-04 (terminal 10) in good condition?
YES : Replace the ETACS-ECU. The power windows
function should now work normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The power
windows function should now work normally.

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-172
STEP 9. Check power window relay connector C-203 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is power window relay connector C-203 in good
condition?
YES : Go to Step 10.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
P.00E-2. When the front power window sub switch
(LH) is operated, the front power window (LH) should
raise and lower normally.
STEP 10. Check the wiring harness between power
window relay connector C-203 (terminal 4) and front power
window sub switch connector E-12 (terminal 6).

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-173
NOTE: Also check junction block connector C-215 and inter-
mediate connector C-26. If junction block connector C-215 or
intermediate connectors C-26 is damaged, repair or replace the
damaged component(s) as described in GROUP 00E, Harness
Connector Inspection P.00E-2.
Q: Is the wiring harness between power window relay
connector C-203 (terminal 4) and front power window
sub switch connector E-12 (terminal 6) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
front power window sub switch is operated, the front
power window (LH) should raise and lower normally.
STEP 11. Check the ground circuit to the front power
window sub switch. Measure the resistance at front power
window sub switch connector E-12.
(1) Disconnect front power window sub switch connector E-12
and measure the resistance available at the wiring harness
side of the connector.
(2) Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 13.
NO : Go to Step 12.

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-177
STEP 18. Check power window relay connector C-203 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is power window relay connector C-203 in good
condition?
YES : Go to Step 19.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
P.00E-2. When the rear power window sub switch
(LH) is operated, the rear power window (LH) should
raise and lower normally.
STEP 19. Check the wiring harness between power
window relay connector C-203 (terminal 4) and rear power
window sub switch (LH) connector E-17 (terminal 6).

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-178
NOTE: Also check junction block connector C-215, intermedi-
ate connectors C-28 and D-19. If junction block connector
C-215, intermediate connector C-28 or D-19 is damaged, repair
or replace the connector as described in GROUP 00E, Harness
Connector Inspection P.00E-2.
Q: Is the wiring harness between power window relay
connector C-203 (terminal 4) and rear power window
sub switch (LH) connector E-17 (terminal 6) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
rear power window sub switch (LH) is operated, the
rear power window (LH) should raise and lower
normally.
STEP 20. Check the ground circuit to the rear power
window sub switch (LH). Measure the resistance at rear
power window sub switch (LH) connector E-17.
(1) Disconnect rear power window sub switch (LH) connector
E-17 and measure the resistance available at the wiring
harness side of the connector.
(2) Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 22.
NO : Go to Step 21.

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-183
STEP 27. Check power window relay connector C-203 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is power window relay connector C-203 in good
condition?
YES : Go to Step 28.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
P.00E-2. When the rear power window sub switch
(RH) is operated, the rear power window (RH) should
raise and lower normally.
STEP 28. Check the wiring harness between power
window relay connector C-203 (terminal 4) and rear power
window sub switch (RH) connector E-06 (terminal 6).

SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)54B-184
NOTE: Also check junction block connector C-215, intermedi-
ate connectors C-28 and D-36. If junction block connector
C-215, intermediate connector C-28 or D-36 is damaged, repair
or replace the connector as described in GROUP 00E, Harness
Connector Inspection P.00E-2.
Q: Is the wiring harness between power window relay
connector C-203 (terminal 4) and rear power window
sub switch (RH) connector E-06 (terminal 6) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. When the
rear power window sub switch (RH) is operated, the
rear power window (RH) should raise and lower
normally.
STEP 29. Check the ground circuit to the rear power
window sub switch (RH). Measure the resistance at rear
power window sub switch (RH) connector E-06.
(1) Disconnect rear power window sub switch (RH) connector
E-06 and measure the resistance available at the wiring
harness side of the connector.
(2) Measure the resistance value between terminal 5 and
ground, and also between terminal 8 and ground.
The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 31.
NO : Go to Step 30.