Page 486 of 1500
ON-VEHICLE SERVICE
SIMPLIFIED WIRING SYSTEM (SWS)54B-486
ON-VEHICLE SERVICE
CONFIGURATION FUNCTIONM1549002500861
ADJUSTMENT BY OPERATING THE
MULTI CENTER DISPLAY
The following function and system customizations
are possible by using the multi center display.
Page 487 of 1500
ON-VEHICLE SERVICE
SIMPLIFIED WIRING SYSTEM (SWS)54B-487
Page 488 of 1500
ON-VEHICLE SERVICE
SIMPLIFIED WIRING SYSTEM (SWS)54B-488
ITEM (multi-center display) ADJUSTMENT DETAILS
Lamps Headlamp auto-cutout functionThe headlamp automatic shutoff function can
be set in the following ways.
a. Auto-cutout only when the ignition is turned
OFF and drivers side door is open while
lamps are on (default- 1 minute timer)
b. Auto-cutout when ignition is turned OFF
and driver side door is open at any time
(adjustable- 3 minute timer)
c. No auto-cutout (adjustable)
Dome lamp cutout time The interior dimmer delay period can be set in
the following ways.
a. 0 second
b. 15 seconds
c. 30 seconds (default)
d. 60 seconds
e. 120 seconds
f. 180 seconds
Interior lamp auto-cutout time The period before the interior illumination is
turned off automatically can be set in the
following ways.
a. 3 minutes
b. 30 minutes (default)
c. 60 minutes
d. No auto-cutout
Wipers Windshield wiper speed-sensitive
operationThe speed-sensitive wiper function can be
activated or deactivated. (ON by default)
Page 489 of 1500
ON-VEHICLE SERVICE
SIMPLIFIED WIRING SYSTEM (SWS)54B-489
Keyless entry and
power door lock
systemKeyless entry system confirmation
by hornThe horn answerback honking conditions can
be set in the following ways.
a. Horn sounds
b. Horn sounds if doors are already locked
c. Horn does not sound (default)
Keyless entry system confirmation
by turn-signal lampsThe hazard answerback flashing conditions
can be set in the following ways.
a. Locking and unlocking (default)
b. Locking only
c. Unlocking only
d. No indication
Time until automatic relocking after
unlock operation using keyless
entry systemThe timed lock period after unlocking with the
keyless entry transmitter can be set to the
following times.
a. 30 seconds (default)
b. 60 seconds
c. 120 seconds
d. 180 seconds
Unlock operation using keyless
entry system or door keyThe unlocking operations after unlocking with
or without a key can be set in the following
ways.
a. Unlock driver's door on first unlock
operation, and unlock all doors on second
unlock operation (default)
b. Unlock all doors on first unlock operation
Buzzers Turn-signal buzzer The turn-signal buzzer function can be
activated or deactivated. (OFF by default)
Door-ajar warning buzzer The door ajar warning buzzer function can be
activated or deactivated (ON by default).
Default Initialization of above mentioned functions ITEM (multi-center display) ADJUSTMENT DETAILS
Page 491 of 1500
INTERIOR52A-2
FRONT SEAT ASSEMBLY* . . . . . . .52A-21
REMOVAL AND INSTALLATION . . . . . . . . 52A-21
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . 52A-23
POWER SEAT CONTINUITY AND
DIAGNOSTIC CHECKS . . . . . . . . . . . . . . . 52A-23
OPERATION CHECK OF POWER
SEAT MOTOR . . . . . . . . . . . . . . . . . . . . . . 52A-29
MEMORY SEAT CONTROLLER (MSC). . . 52A-31
DISASSEMBLY AND ASSEMBLY RH SIDE52A-33
DISASSEMBLY AND ASSEMBLY LH SIDE52A-37
REMOVAL SERVICE POINT . . . . . . . . . . . 52A-42
FRONT SEAT TRIM COVER
REMOVAL AND FITMENT . . . . . . . . . . . . . 52A-43
REAR SEAT CUSHION TRIM COVER
REMOVAL AND FITMENT . . . . . . . . . . . . . 52A-46
REAR SEAT BACK TRIM COVERREMOVAL AND FITMENT . . . . . . . . . . . . . 52A-49
REAR SEAT ASSEMBLY . . . . . . . . . .52A-55
REMOVAL AND INSTALLATION . . . . . . . . 52A-55
DISASSEMBLY AND REASSEMBLY . . . . . 52A-57
FRONT SEAT BELT* . . . . . . . . . . . . .52A-58
REMOVAL AND INSTALLATION . . . . . . . . 52A-58
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . 52A-59
REAR SEAT BELT . . . . . . . . . . . . . . .52A-59
REMOVAL AND INSTALLATION . . . . . . . . 52A-59
SPECIFICATIONS . . . . . . . . . . . . . . .52A-60
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . 52A-60
Page 492 of 1500
GENERAL DESCRIPTION
INTERIOR52A-3
GENERAL DESCRIPTIONM1521000100184
OPERATION
.
Seat belt warning system
If the driver turn the ignition switch to the "ON" posi-
tion without fastening the seat belt, the seat belt
warning light illuminates.
SEAT BELT DIAGNOSISM1523000700182
The seat belt warning system is controlled by the
Simplified Wiring System (SWS). For troubleshoot-
ing, refer to GROUP 54B, SWS diagnosis
P.54B-101.
SPECIAL TOOLSM1521000600327
TOOL TOOL NUMBER AND
NAMESUPERSESSION APPLICATION
MB990784
Ornament removerGeneral service
toolRemoval of switch, trim,
etc.
Page 493 of 1500
INSTRUMENT PANEL ASSEMBLY
INTERIOR52A-4
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATIONM1521001700684
Refer to GROUP 52B, SRS Service Precautions P.52B-16 and Air bag Module and Clock Spring
P.52B-237 before removing the passenger side air bag module.
Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.
The following bolts and screws are used for installing the instrument panel. Bolts and screws are indicated as
marks shown in the illustration in the sections of "Removal and Installation" and "Disassembly and Assem-
bly."
NAME SYMBOL SIZE (D
L) mm COLOR SHAPE
TAPPING SCREW a 5
12 BLACK
b5
16 -
c5
20 -
d5
20 BLACK
e6
16 GREEN
f8
15 -
WASHER
ASSEMBLY BOLTg6
16 -
h6
25 -
i6
16 -
Page 497 of 1500
