I31546
I31561
(A)
(B)
I31544
(E)
(C)(D)
- HEATER & AIR CONDITIONERCOOLER COMPRESSOR ASSY
55-41
2656 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
13. INSPECT COMPRESSOR OIL
(a) When replacing the compressor and magnetic clutch with new one, after gradually removing the refrig-
erant gas from the service valve, drain the following amount of oil from the new compressor and mag-
netic clutch before installation.
Standard:
(Oil capacity inside new compressor and magnetic clutch: 120 + 15 cc (4.1 + 0.51 fl.oz.) ) - (Re-
maining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be re-
moved when replacing)
NOTICE:
When checking the compressor oil level, observe the precautions on the cooler removal/instal-
lation.
Because compressor oil remains in the pipes of the vehicle, if a new compressor and magnetic
clutch is installed without removing some oil inside, the oil amount becomes too much, pre-
venting heat exchange in the refrigerant cycle and causing refrigerant failure.
If the remaining oil in the removed compressor and magnetic clutch is too small in volume,
check for oil leakage.
Be sure to use ND-OIL8 for compressor oil.
14. TEMPORARY TIGHTEN COMPRESSOR AND
MAGNETIC CLUTCH
(a) Temporarily the compressor and magnetic clutch with the
3 bolts.
15. FULLY TIGHTEN COMPRESSOR AND MAGNETIC
CLUTCH
(a) Tighten the compressor and magnetic clutch with the bolt
(A) and bolt (B).
Torque: 25 NVm (250 kgfVcm, 18 ftVlbf)
(b) Install the cooler compressor bracket with the 2 bolts and
nut.
Torque:
25 NVm (250 kgfVcm, 18 ftVlbf) (Bolt (C))
25 NVm (250 kgfVcm, 18 ftVlbf) (Nut (D))
18 NVm (184 kgfVcm, 13 ftVlbf) (Bolt (E))
170F5-03
A78720
SST
P12582
Additional
3/4 TurnSST
17-20
- LUBRICATIONOIL FILTER SUB-ASSY (3MZ-FE)
2325 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OIL FILTER SUB-ASSY (3MZ-FE)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with engine oil will cause removal of natural oils from the skin,
leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially
harmful contaminants which may cause skin cancer.
Precautions should be taken when replacing engine oil to minimize the risk of your skin making
contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly
with soap and water, or use water-less hand cleaner to remove any used engine oil. Do not use
gasoline, thinners, or solvents.
For environmental protection used oil and used oil filter must be disposed of at designated dis-
posal sites.
1. REMOVE ENGINE UNDER COVER NO.1
2. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, then drain the oil into a container.
(c) Clean and install the oil drain plug with a new gasket.
Torque: 45 NVm (459 kgfVcm,
33 ftVlbf)
3. REMOVE OIL FILTER SUB-ASSY
(a) Using SST, remove the oil filter.
SST 09228-07501
4. INSTALL OIL FILTER SUB-ASSY
(a) Check and clean the oil filter installation surface.
(b) Apply clean engine oil to the gasket of a new oil filter.
(c) Lightly screw the oil filter into place, then tighten it until the
gasket contacts the seat.
(d) Using SST, tighten it an additional 3/4 turn.
SST 09228-07501
5. ADD ENGINE OIL
(a) Fill with fresh engine oil.
Capacity:
Drain and refill with oil filter change4.7 liters (5.0 US qts, 4.1 lmp. qts)
Drain and refill without oil filter change4.5 liters (4.8 US qts, 4.0 lmp. qts)
Dry fill5.5 liters (5.8 US qts, 4.8 lmp. qts)
6. CHECK FOR ENGINE OIL LEAKS
