2005 LEXUS ES300 air tubes

320DY-06
F40991
Front Brake Tube
Frame No.1
F40992
F40004
- BRAKEBRAKE MASTER CYLINDER SUB-ASSY
32-21
2455 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
BRAKE MASTER CYLINDER SUB-ASSY (From August,
2002)
OVERHAUL
1. REMOVE AIR CLEANER ASSY
2. DRAIN BRAKE FLUID
NOTICE:
Wash off the brake fluied immediately if it comes into contact with a painted surface.
3. REMOVE BRAKE MASTER CYLINDER SUB-ASSY
(a) Disconnect the level warning switch connector.
(b) Using SST, remove the front brake tube frame No.1.
SST 09023-00101
(c) Using SST, disconnect the 4 brake tubes from the master
cylinder.
SST 09023-00101
(d) Remove the 2 nuts, pull out the 2-way and brake master
cylinder sub-assy.
4. REMOVE BRAKE MASTER CYLINDER RESERVOIR FILLER CAP ASSY
(a) Remove the master cylinder reservoir filler cap assy.
5. REMOVE BRAKE MASTER CYLINDER RESERVOIR STRAINER
(a) Remove the master cylinder reservoir strainer.
6. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSY
(a) Remove the screw and pull out the master cylinder reservoir sub-assy.
7. REMOVE MASTER CYLINDER RESERVOIR GROMMET
(a) Remove the 2 master cylinder reservoir grommets.
8. REMOVE BRAKE MASTER CYLINDER KIT (W/O VSC)
(a) Place master cylinder in vise.
(b) Remove the O-ring.
(c) Push in the piston and remove the snap ring with snap
ring pliers.

F40006
SST
F40992
F40991
Front Brake Tube
Frame No. 1
- BRAKEBRAKE MASTER CYLINDER SUB-ASSY
32-25
2459 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(e) Using SST, adjust the booster push rod length until the
push rod lightly touches the pin head.
SST 09737-00020
18. INSTALL BRAKE MASTER CYLINDER SUB-ASSY
(a) Install the master cylinder sub-assy and 2-way with the
2 nuts.
Torque: 13 NVm (130 kgfVcm, 9 ftVlbf)
(b) Using SST and connect the 4 front brake tubes to the
master cylinder sub-assy.
Torque: 15 NVm (155 kgfVcm, 11 ftVlbf)
SST 09023-00101
(c) Using SST and install the front brake tube frame No.1 to
the master cylinder.
Torque: 15 NVm (155 kgfVcm, 11 ftVlbf)
SST 09023-00101
(d) Connect the level warnig switch connector.
19. FILL RESERVOIR WITH BRAKE FLUID
20. BLEED MASTER CYLINDER (SEE PAGE 32-4)
SST 09023-00101
21. BLEED BRAKE LINE (SEE PAGE 32-4)
22. INSTALL AIR CLEANER ASSY
23. CHECK FLUID LEVEL IN RESERVOIR (SEE PAGE 32-4)
24. CHECK BRAKE FLUID LEAKAGE

110XT-02
Fuel Tube Connector
A50710
Fuel Tube Connector
SST
(Hose)
B12947
A86391
SST
(Hose)
SST
(Union)
O-ring
Vinyl TubeSST
(Clamp)
11-8
- FUELFUEL SYSTEM (3MZ-FE)
2036 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
INSPECTION
1. INSPECT FUEL INJECTOR ASSY
(a) Inspect the resistance.
(1) Using an ohmmeter, measure the resistance be-
tween the terminals.
Standard:
Tester ConnectionSpecified Condition
1 - 213.4 to 14.2 W at 20C (68F)
If the resistance is not as specified, replace the fuel injector.
(b) Check the operation.
CAUTION:

This test involves high-pressure fuel and electricity.
Keep the injector free of sparks during the test.

Take every precaution regarding safe handling of
both the fuel and electricity.

Perform this test in a safe area, and avoid any sparks
or flame.

Do not smoke.
(1) Pull out the fuel tube connector from a new fuel
tube.
HINT:
Part No. 23801 - 20190
(2) Connect SST and the fuel tube connector to the fuel
pipe.
SST 09268-41047 (95336-08070)
CAUTION:
After taking the precautions, connect the quick connector.
(3) Install the grommet and O-ring to the fuel injector.
(4) Connect SST (a union and hose) to the fuel injector,
then hold the fuel injector and union with SST (a
clamp).
SST 09268- 41047 (09268- 41110, 09268- 41300,
95336-08070)
(5) Put the fuel injector into a graduated cylinder.
HINT:
Install a suitable vinyl tube to the fuel injector to contain the gas-
oline spray.