Page 127 of 969

D03623
Snap Ring
D26392
BA
Overdrive Direct
Clutch Hub
D26403
Thrust Bearing
Direct Clutch Assy
D26469
C
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-55
79 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(c) Temporarily remove the snap ring, attach the selected
flange and restore the snap ring.
NOTICE:
Secure the snap ring so that its gap is visible through the
groove of the transaxle case.
109. I N S TA L L O V E R D R E V E D I R E C T C L U T C H H U B
SUB-ASSY
(a) Install the direct clutch hub to the planetary gear assy.
NOTICE:
Be careful not to damage the bush inside of the overdrive
clutch hub during instaling.
(b) Coat the thrust bearing with ATF.
(c) Install the bearing race and the thrust bearing to the direct
clutch hub.
NOTICE:
Installing the bearing, hold the part on the side of the over-
drive clutch hub.
Bearing and race diameter: mm (in.)
InsideOutside
Bearing, A24.7 (0.972)39.5 (1.555)
Race, B23.6 (0.929)38.0 (1.496)
110. INSTALL DIRECT CLUTCH ASSY
(a) Coat the thrust bearing with ATF.
(b) Install the direct clutch assy and thrust bearing to the rear
planetary sun gear assy.
NOTICE:
The disc in the direct clutch should completely match with
the hub attached outside the rear planetary sun gear.
Otherwise, the rear cover can not be installed.
(c) Clean the connecter part of the transaxle case and the
rear cover.
(d) As shown in the illustration, place a straight edge on the
direct clutch drum and measure the distance between
transaxle case and the straight edge using vernier cali-
pers (Dimension C).
Page 129 of 969

D26766
SST
D26389
Rear Clutch
Oil Seal
Ring Outer
D26388
D26454
FIPG
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-57
81 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
113. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the transaxle rear cover.
SST 09950-60010 (09951-00230, 09952-06010)
Press fit depth: 20.55 - 21.25 mm (0.8091 - 0.8366 in.)
NOTICE:
Face the inscribed mark side of the bearing race up.
Repeat the press fit until the specified value is ob-
tained.
(b) Coat a needle roller bearing with ATF.
114. INSTALL REAR CLUTCH OIL SEAL RING OUTER
(a) Coat the 3 new rear clutch oil seal rings with ATF, install
them to the transaxle rear cover.
NOTICE:
The snap ring should be fixed certainly in the groove of the
drum.
115. INSTALL TRANSAXLE CASE NO.1 PLUG
(a) Install the 4 new O-ring to the 4 transaxle case No. 1
plugs.
(b) Install the 4 transaxle case No. 1 plugs to the transaxle
rear cover.
Torque: 7.4 NVm (75 kgfVcm, 65 in.Vlbf)
116. INSTALL TRANSAXLE REAR COVER SUB-ASSY
(a) Remove any packing material and be careful not to get oil
on the contacting surfaces of the transaxle rear cover or
the transaxle case.
(b) Apply FIPG to the cover.
FIPG:
Part No. 08826-00090, THREE BOND 1281 or equiva-
lent.
NOTICE:
Concerning about the amount of the FIPG application, the
amount should be controlled to from even sealing film on
entire flange surface and have slight protrusion of the FIPG
all around of the connecting area. The FIPG shall be ap-
plied continuously on the flange. (Reference value of the
section diameter: f1.2)
Page 130 of 969

D26387AA
D26414
Flange
Plate Disc
D26466
Snap Ring
D08082
40-58
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
82 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(c) Apply liquid sealer to the ºAº bolt threads.
Sealant:
Part No. 08833-00080, THREE BOND 1344, LOCTITE
242 or equivalent.
(d) Install the 11 bolts.
Torque:
Bolt A: 19.0 NVm (190 kgfVcm, 14 ftVlbf)
Other bolt: 25.0 NVm (250 kgfVcm, 18 ftVlbf)
117. INSTALL UNDERDRIVE CLUTCH DISC NO.2
(a) Coat the 4 discs with ATF.
(b) Install the 4 discs, 4 plates and flange to the transaxle
case.
NOTICE:
Be careful about the order of discs, plate and flange assem-
bly.
(c) Using a screwdriver, install the snap ring.
NOTICE:
The snap ring should be fixed certainly in the groove of the
drum.
118. INSPECT PACK CLEARANCE OF UNDERDRIVE
BRAKE
(a) Using a dial indicator, measure the underdrive brake pack
clearance while applying and releasing compressed air
(392 kPa, 4.0 kgf/cm
2, 57 psi).
Pack clearance: 1.81 - 2.20 mm (0.0713 - 0.0866 in.)
HINT:
Select an appropriate flange from the table below so that it will
meet the specified value.
Flange thickness: mm (in.)
MarkThicknessMarkThickness
13.0 (0.118)43.1 (0.122)
23.2 (0.126)53.3 (0.130)
33.4 (0.134)--
(b) Temporally remove the snap ring and attach to the flange.
(c) Restore the snap ring.
Page 134 of 969

D26710
Thrust Needle
Roller BearingMultiple Disc
Clutch Clutch
Hub
D26711
Thrust Needle
Roller BearingMultiple Disc
Clutch Clutch
Hub
D03820
Thrust Needle
Roller Bearing
D03574
Forward Clutch Assy
40-62
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
86 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(b) Coat the thrust needle roller bearing and race with yellow
petrolatum, install them onto the multiple disc clutch hub.
Thrust bearing and race diameter: mm (in.)
InsideOutside
Thrust Bearing36.4 (1.433)52.2 (2.055)
(c) Coat the needle roller bearing with ATF.
(d) Install the needle roller bearing to the multiple clutch hub.
Bearing diameter: mm (in.)
InsideOutside
Bearing23.6 (0.929)44 (1.732)
(e) Install the multiple clutch hub to the transaxle case.
125. INSTALL FORWARD CLUTCH ASSY
(a) Coat the thrust needle roller bearing with ATF.
(b) Install the thrust needle roller bearing to the forward
clutch.
Thrust bearing diameter: mm (in.)
InsideOutside
Thrust Bearing33.58 (1.3220)51.9 (2.043)
NOTICE:
Install the thrust bearing properly so that the no colored
race or blue ink jet race will be visible.
(c) Install the forward clutch to the forward clutch assy.
NOTICE:
Align the splines of all discs in the forward clutch with
those of multiple clutch hub to assemble them se-
curely.
Be careful not to damage the bush inside of the for-
ward clutch hub during installing.
Page 135 of 969

D03573
D26450
Differential
Gear Assy
D25506
Thrust Bearing
Underdrive
Race No.2Underdrive Planetary
Gear Assy
Forward Clutch
Assy
Differential Gear Assy
Forward Clutch
Assy
D25505
Thrust
Needle
Roller Bearing
Differential Gear Assy
Underdrive Planetary
Gear Assy
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-63
87 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
126. INSTALL OVERDRIVE BRAKE GASKET
(a) Install the 2 new overdrive brake gaskets.
127. INSTALL DIFFERENTIAL GEAR ASSEMBLY
(a) Install the differential gear assy to the transaxle case.
128. INSTALL THRUST BEARING UNDERDRIVE RACE
NO.2
(a) Install the thrust bearing underdrive race No.2 to the un-
derdrive planetary gear assy.
129. INSTALL THRUST NEEDLE ROLLER BEARING
(a) Coat the thrust needle roller bearing with ATF.
(b) Calculate the end play value using the following formula
and values of Dimension E and F that ware measured
when installing cylindrical roller bearing and underdrive
planetary gear. Select an appropriate underdrive plane-
tary gear thrust bearing race No. 2 which satisfies the spe-
cified end play value, and install it.
End play: 0.498 - 0.993 mm (0.01961 - 0.03909 in.)
HINT:
End play = Dimension F - Dimension E - thrust bearing thick-
ness 2.5 mm (0.0984 in.) - underdrive thrust bearing race No.
2 thickness.
Race thickness: mm (in.)
F - EThickness
Less than 7.72 (0.3039)3.5 (0.138)
7.72 (0.3039)3.8 (0.150)
Page 136 of 969
D03569
D03629
O-ring
D03630Seal Bend Width 1.2 mm (0.047 in.) FIPG
40-64
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
88 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
Bearing and bearing race diameter: mm (in.)
InsideOutside
Bearing57.2 (2.252)84.96 (3.345)
Bearing race56.4 (2.22)83 (3.268)
130. INSTALL OIL PUMP ASSY
(a) Install the oil pump to the transaxle case with the 7 bolts.
Torque: 22.0 NVm (226 kgfVcm, 16 ftVlbf)
(b) Coat the O-ring of oil pump with ATF.
NOTICE:
Confirm the input shaft rotates smoothly with the manual
operation after assembling the oil pump.
131. INSTALL TRANSAXLE HOUSING
(a) Remove any parking material and be careful not to get oil
on the contacting surface of the transaxle case or trans-
axle housing.
(b) Apply FIPG to the transaxle case.
FIPG:
Part No. 08826-00090, THREE BOND 1281 or equiva-
lent
Page 139 of 969

D03561
D03560
B
A
D03904
O-ring
B-3 Accumulator Piston
D25512
AT F
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
40-67
91 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
138. INSTALL PARKING LOCK PAWL BRACKET
(a) Install the parking lock pawl bracket with the 2 bolts.
Torque: 20 NVm (205 kgfVcm, 15 ftVlbf)
Bolt length: 25 mm (0.984 in.)
NOTICE:
Be sure the parking rod is placed between the parking pawl
and the guide of the parking bracket when the parking
bracket is assembled.
139. INSTALL MANUAL DETENT SPRING SUB-ASSY
(a) Install the manual detent spring with the 2 bolts.
NOTICE:
Make sure to install the manual detent spring and cover in
this order.
HINT:
Tighten them in the order, A and B.
Torque:
Bolt A: 20 NVm (205 kgfVcm, 15 ftVlbf)
Bolt B: 12 NVm (120 kgfVcm, 9 ftVlbf)
Bolt length:
Bolt A: 27 mm (1.063 in.)
Bolt B: 16 mm (0.630 in.)
140. INSTALL B-3 ACCUMULATOR PISTON
(a) Coat a new O-ring with ATF, install it to the B-3 accumula-
tor piston.
NOTICE:
Install the O-ring to the accumulator piston and the accu-
mulator sleeve not to have a twist and a protrusion. More-
over, apply enough ATF prior to assembling. Be sure to the
installed position.
(b) Coat the piston with ATF, install it to the transaxle case.
NOTICE:
Install the springs to each accumulator piston with check-
ing of the identification color or each spring.
Accumulator spring:
Free length
Outer diameter mm (in.)Color
Inner 62.00 (2.4409) /
15.50 (0.610)Purple
Outer 74.23 (2.9224) /
21.70 (0.854)Purple
Page 140 of 969

D26402
O-ring
O-ring Reverse clutch Accumulator Piston
C92978
AT F
D03902
O-ring
C-3 Accumulator Piston
C83146
D03555
40-68
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E/U151F)
92 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
141. I N S TA L L REVERSE CLUTCH ACCUMULATOR
PISTON
(a) Coat the 2 new O-rings with ATF, install them to the re-
verse accumulator piston.
NOTICE:
Install the O-ring to the accumulator piston and the accu-
mulator sleeve not to have a twist and a protrusion. More-
over, apply enough ATF prior to assembling. Be sure to the
installed position.
(b) Coat the piston with ATF, install it to the transaxle case.
NOTICE:
Install the springs to each accumulator piston with check-
ing of the identification color or each spring.
Accumulator spring:
Free length
Outer diameter mm (in.)Color
60.96 (2.3999) /
14.10 (0.555)Yellow
142. INSTALL C-3 ACCUMULATOR PISTON
(a) Coat a new O-ring with ATF, install it to the C-3 accumu-
lator piston.
NOTICE:
Install the O-ring to the accumulator piston and the accu-
mulator sleeve not to have a twist and a protrusion. More-
over, apply enough ATF prior to assembling. Be sure to the
installed position.
(b) Coat the piston with ATF, install it to the transaxle case.
NOTICE:
Install the springs to each accumulator piston with check-
ing of the identification color or each spring.
Accumulator spring:
Free length
Outer diameter mm (in.)Color
72.20 (2.8425) /
19.0 (0.748)Colorless
(c) Install the spring from the C-3 accumulator piston.
NOTICE:
Install the springs to each accumulator piston with check-
ing of the identification color or each spring.