2005 LEXUS ES300 transmission

A86279
Push
A86339
Push
A86280
Push 11-32
- FUELFUEL TANK ASSY (3MZ-FE)
2060 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
17. INSTALL FUEL TANK CUSHION NO.2
(a) Install 7 new fuel tank cushions to the fuel tank.
18. INSTALL FUEL MAIN TUBE SUPPORT
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
19. INSTALL FUEL PUMP TUBE SUB-ASSY
20. INSTALL FUEL TANK VENT HOSE
(a) Push in the quick connector to the pipe until the quick con-
nector makes a ºclickº sound.
NOTICE:

Check the connected part for damage or foreign ob-
jects.

After connecting, check if the quick connector and
pipe are securely connected by pulling on them.
21. INSTALL FUEL TANK ASSY
(a) Install the 4 clip nuts.
(b) Install the 2 fuel tank bands with the 2 pins.
(c) Set up the fuel tank to the transmission jack.
(d) Connect the fuel tank vent hose to the charcoal canister.
(1) Push in the quick connector to the pipe until the
quick connector makes a ºclickº sound.
NOTICE:

Check the connected part for damage or foreign ob-
jects.

After connecting, check if the connector and pipe are
securely connected by pulling on them.
(e) Operate the transmission jack, then connect the fuel tank
filler pipe.
(f) Tighten the clamp bolt.
(g) Tighten the 2 bolts which hold the fuel tank bands.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(h) Connect the fuel tube No. 1.
(1) Push in the quick connector to the pipe until the
quick connector makes a ºclickº sound.
NOTICE:

Check the connected part for damage or foreign ob-
jects.

After connecting, check if the quick connector and
pipe are securely connected by pulling on them.

Lexus Supports ASE CertificationPage 1 of 3
Title:
ECM RESET MEMORY FUNCTION
Models:
'98 ± '05 Applicable Models
Technical Service
Information Bulletin
May 5, 2003
TC002-03
TSIB REVISION NOTICE:
December 20, 2004: Applicable Vehicles section has been updated and modified,
2004 and 2005 model years added; and Reset Procedure 2 has been revised.
Previous versions of this TSIB should be discarded.
Whenever an automatic transmission is replaced, overhauled or individual components
are replaced, use this procedure to erase Engine Control Module (ECM, SAE term:
Powertrain Control Module, PCM) ªLearned Valuesº and minimize subsequent
performance concerns.
CAUTION:
Failure to follow the following procedure may lengthen the time to readjust the
ªLearned Values,º potentially resulting in performance concerns.
Refer to Reset Procedure 1 for the following vehicles with Electronically Controlled
Automatic Transmissions:
1999 ± 2003 model year ES 300 and RX 300 vehicles.
2003 ± 2005 model year GX 470 vehicles.
2004 ± 2005 model year RX 330 vehicles.
Refer to Reset Procedure 2 for the following vehicles with Electronically Controlled
Automatic Transmissions:
1998 ± 2005 model year GS 430/400/300, LS 430/400, LX 470, and
SC 430/400/300 vehicles.
2001 ± 2005 model year IS 300 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
TRANSMISSION & CLUTCH
Introduction
Applicable
Vehicles
Warranty
Information

RESET MEMORY FUNCTION ± TC002-03 Revised May 5, 2003
Page 2 of 3
SPECIAL SERVICE TOOLS (SSTs)PART NUMBERQUANTITY
Lexus Diagnostic Tester Kit*010012701
CAN Interface Module Kit*010027441
12 Megabyte Diagnostic Tester Program Card
with version 12.01a Software (or later)*01002593-0051
* Essential SSTs.
NOTE:
Additional Diagnostic Tester Kits, CAN Interface Modules, Program Cards or other
SSTs may be ordered by calling SPX/OTC at 1-800-933-8335.
1. Connect the Lexus Diagnostic Tester to the vehicle.
2. Reset the ECM (PCM). Refer to the procedures below.
DO YOU WISH TO
RESET THE ECM?
[YES] to CONTINUE
[NO] to EXIT
2: CUSTOMIZE
3: ECU REPROGRAMFUNCTION SELECT FOR
NORTH AMERICA
B
*APPLICATION SELECT*
A
1: DIAGNOSISDIAGNOSTIC MENU
ENGINE
C
DO NOT USE THIS
FUNCTION UNLESS
INSTRUCTED BY
REPAIR MANUAL.RESET MEMORY
E
RESET MEMORY
NOTICE
D
[YES]
F
1: OBD/MOBD
3: CARB OBD II
4: BREAK±OUT BOX
5: NVH
6: AUTOPROBE
7: 02 RPM CHECK
8: SNAPSHOT REVIEW
9: SETUP
0: GAS ANALYSIS2: ENHANCED OBD II1: DATA LIST
2: DTC INFO
3: ACTIVE TEST
4: SNAPSHOT
5: SYSTEM CHECK
6: RESET MEMORY
7: MONITOR STATUS
8: CHECK MODE
6: RESET MEMORY
ONLY USE AFTER
REPLACING THE ENGINE,
AUTO TRANS, OR ECM
ON CERTAIN VEHICLES.EXECUTING THIS
FUNCTION WILL RESET
THE LEARNED VALUES
IN THE ECM.RESET MEMORY
RESETTING COMPLETE
PRESS
[ENTER]
3. Start the engine and warm it up to normal operating temperatures before test±driving.
4. Perform a thorough test drive with several accelerations from a stop with ªlight
throttleº application until proper transmission shifting is verified.
Required
SSTs
Reset
Procedure 1

RESET MEMORY FUNCTION ± TC002-03 Revised May 5, 2003
Page 3 of 3
1. Disconnect the negative battery cable for 5 minutes.
2. Reconnect battery cable.
3. Start the engine and warm it up to normal operating temperatures before test±driving.
4. Perform a thorough test drive with several accelerations from a stop with ªlight
throttleº application until proper transmission shifting is verified.Reset
Procedure 2

Lexus Supports ASE CertificationPage 1 of 6
Title:
ECM CALIBRATION: SHIFT FEELING
ENHANCEMENT
Models:
'02 ± '03 ES 300 & '04 ± '05 ES 330
Technical Service
Information Bulletin
August 4, 2003
TC004-03
REVISION NOTICE:
April 1, 2005: 2004 ± 2005 model year ES 330 vehicles have been added to
Applicable Vehicles. Introduction and Note have been updated on page 1.
Calibration Identification Chart has been updated to include ES 330 calibration IDs.
August 6, 2003: There has been a change in Warranty Time.
Previous versions of this TSIB should be discarded.
To improve the transmission shift feeling during specific operating modes, the Engine
Control Module (SAE term: Powertrain Control Module/PCM) calibration has been
revised. These improvements include:
Reduced downshift lag when accelerating at speeds from 10 to 20 mph.
Less gear hunting when driving on/off accelerator pedal at 20 to 30 mph
(for example: during heavy rush±hour traffic).
Improved response rate during heavy acceleration from a stop.
NOTE:
Version 12.01a or later Diagnostic Tester software is required to perform
this procedure.
Before proceeding, verify the ECM (PCM) calibration has NOT been updated by
checking for the Authorized Modifications Label (shown in step 1 of the
Repair Procedure).
Harsh ATM shifting may result if any Repair Procedure steps are omitted
(specifically steps 2 and 4 of ªFlash Reprogram ECMº on page 6).
2002 ± 2003 model year ES 300 vehicles.
2004 ± 2005 model year ES 330 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
EG5017Recalibrate ECM Engine & Transmission0.9
89666±3325#
89666±3344#
89661±33B3#
89661±33A4#
2699
Applicable Warranty*:
This repair is covered under the Lexus Federal Emissions Warranty. This warranty is
in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's
in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
TRANSMISSION & CLUTCH
Introduction
Applicable
Vehicles
Warranty
Information