2005 LEXUS ES300 torque

A86568
A05189
A80061
Oil Pressure
Switch 14-34
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2126 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
80. REMOVE MANIFOLD STAY NO.2
(a) Remove the 2 bolts and manifold stay.
81. REMOVE ENGINE MOUNTING BRACKET RH (See page 17-9)
82. REMOVE PUMP BRACKET
(a) Remove the 3 bolts and pump bracket.
83. REMOVE GENERATOR BRACKET NO.1
84. REMOVE COMPRESSOR MOUNTING BRACKET NO.1 (See page 17-9)
85. REMOVE WATER INLET PIPE (See page 16-16)
86. REMOVE WATER INLET (See page 16-16)
87. REMOVE THERMOSTAT
88. REMOVE ENGINE OIL PRESSURE SWITCH ASSY
(a) Using a deep socket wrench 24 mm, remove the oil pres-
sure switch.
89. REMOVE KNOCK SENSOR (See page 10-16)
90. REPLACE PARTIAL ENGINE ASSY
91. INSTALL KNOCK SENSOR (See page 10-16)
92. INSTALL ENGINE OIL PRESSURE SWITCH ASSY
(a) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833-00080 THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Using a deep socket wrench 24 mm, install the oil pressure switch.
Torque: 15 NVm (153 kgfVcm, 11 ftVlbf)

A86567
3
4
7
25
61
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-35
2127 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
93. INSTALL THERMOSTAT (See page 16-16)
94. INSTALL WATER INLET (See page 16-16)
95. INSTALL WATER INLET PIPE (See page 16-16)
96. INSTALL COMPRESSOR MOUNTING BRACKET NO.1 (See page 17-9)
97. INSTALL GENERATOR BRACKET NO.1
Torque: 58 NVm (591 kgfVcm, 43 ftVlbf)
98. INSTALL PUMP BRACKET
Torque: 32 NVm (326 kgfVcm, 24 ftVlbf)
99. INSTALL ENGINE MOUNTING BRACKET RH (See page 17-9)
100. INSTALL MANIFOLD STAY NO.2
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
101. I N S TA L L E XHAUST MANIFOLD CONVERTER
SUB-ASSY NO.2
(a) Install a new gasket and the exhaust manifold converter
No. 2 with the 7 nuts. Using several steps, tighten the nuts
uniformly in the sequence shown in the illustration.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
(b) Retighten nuts 1 and 2 as shown in the illustration.
102. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.2
Torque: 8.5 NVm (87 kgfVcm, 75 in.Vlbf)
103. INSTALL MANIFOLD CONVERTER INSULATOR NO.3
Torque: 8.5 NVm (87 kgfVcm, 75 in.Vlbf)
104. INSTALL EXHAUST MANIFOLD SUB-ASSY RH (See page 14-120)
105. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.1 (See page 14-120)
106. INSTALL IGNITION COIL ASSY (See page 14-7)
107. INSTALL WATER OUTLET (See page 10-16)
108. INSTALL INTAKE MANIFOLD (See page 10-16)
109. INSTALL INTAKE AIR SURGE TANK (See page 11-13)
110. INSTALL EMISSION CONTROL VALVE SET (See page 11-13)
111. INSTALL DRIVE PLATE & RING GEAR SUB-ASSY (See page 14-140)
SST 09213-54015 (91651-60855), 09330-00021
112. INSTALL DRIVE SHAFT BEARING BRACKET
Torque: 64 NVm (650 kgfVcm, 47 in.Vlbf)
113. INSTALL AUTOMATIC TRANSAXLE ASSY (See page 40-9)
114. INSTALL EXHAUST PIPE SUPPORT BRACKET NO.1 (See page 40-9)
115. INSTALL ENGINE MOUNTING BRACKET FR (See page 40-9)
116. INSTALL STARTER ASSY (See page 19-5)

A78403
RH: LH:
A60501
A52890
A78549
14-36
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2128 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
117. INSTALL FRONT DRIVE SHAFT ASSY LH (See page 30-8)
118. INSTALL FRONT DRIVE SHAFT ASSY RH (See page 30-8)
119. INSTALL FRONT FRAME ASSY
(a) Install the engine mounting insulator RH and LH with the
2 nuts.
Torque: 95 NVm (969 kgfVcm, 70 ftVlbf)
(b) Install the engine mounting insulator FR with the bolt.
Torque: 87 NVm (887 kgfVcm, 64 ftVlbf)
120. INSTALL VANE PUMP ASSY
(a) Temporarily tighten the bolt.
(b) Install the adjusting strut to the engine mounting bracket
RH with the bolt.
Torque: 43 NVm (439 kgfVcm, 32 ftVlbf)
(c) Connect the power steering pressure tube with the 2 nuts.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
121. INSTALL VANE PUMP V BELT (See page 14-5)

A59877
BNut
A
BNut
A
A59878
Nut
D
CNut
D
C
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-37
2129 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
122. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
(a) Set the engine assembly with the transaxle on the engine
lifter.
(b) Install the engine assembly to the vehicle.
(c) Install the frame side rail plate RH and LH with the 4 bolts
and 2 nuts.
Torque:
85 NVm (867 kgfVcm, 63 ftVlbf) for bolt A
32 NVm (326 kgfVcm, 24 ftVlbf) for bolt B and nut
(d) Install the front suspension member brace rear RH and
LH with the 4 bolts and 2 nuts.
Torque:
85 NVm (867 kgfVcm, 63 ftVlbf) for bolt C
32 NVm (326 kgfVcm, 24 ftVlbf) for bolt D and nut
123. CONNECT STEERING INTERMEDIATE SHAFT ASSY (See page 51-21)
124. INSTALL FRONT AXLE ASSY LH (See page 30-8)
125. INSTALL FRONT AXLE ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
126. INSTALL FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH (See page 30-8)
127. INSTALL FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 RH
HINT:
Perform the same procedure as above on the opposite side.
128. INSTALL TIE ROD ASSY LH (See page 30-8)
129. INSTALL TIE ROD ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
130. INSTALL SPEED SENSOR FRONT LH (See page 30-8)
131. INSTALL SPEED SENSOR FRONT RH
HINT:
Perform the same procedure as above on the opposite side.
132. INSTALL FRONT AXLE HUB LH NUT (See page 30-8)
133. INSTALL FRONT AXLE HUB RH NUT
HINT:
Perform the same procedure as above on the opposite side.
134. INSTALL FRONT STABILIZER LINK ASSY LH (See page 30-8)
135. INSTALL FRONT STABILIZER LINK ASSY RH
HINT:
Perform the same procedure as above on the opposite side.
136. INSTALL EXHAUST PIPE ASSY FRONT (See page 15-2)
137. INSTALL EXHAUST PIPE NO.1 SUPPORT BRACKET REAR (See page 15-2)
138. INSTALL EXHAUST PIPE NO.1 SUPPORT BRACKET FRONT (See page 15-2)
139. CONNECT FUEL PIPE SUB-ASSY NO.1 (See page 11-1)

A86570
From Canister
Vacuum Tank
Actuator Actuator
Vacuum Surge
TankVSV for EVAP
VSV for ACIS
Engine Mounting
Insulator FR
VSV for Active Control
Engine MountCapVSV Vacuum Hose Routing Diagram:
14-38
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2130 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
140. CONNECT TRANSMISSION CONTROL CABLE ASSY (See page 40-44)
141. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (See page 17-9)
142. INSTALL GENERATOR BELT ADJUSTING BAR (See page 17-9)
143. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
144. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
145. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
146. INSTALL GENERATOR ASSY (See page 19-21)
147. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
148. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
149. INSTALL INTAKE AIR RESONATOR SUB-ASSY
Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
150. INSTALL AIR CLEANER INLET NO.1 (See page 19-5)
151. INSTALL AIR CLEANER BRACKET (See page 19-5)
152. INSTALL AIR CLEANER ASSY (See page 19-5)
153. INSTALL AIR CLEANER INLET ASSY (See page 19-5)
154. CHECK CONNECTION OF VACUUM HOSE
155. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
156. INSTALL FRONT WHEELS (See page 14-5)

A78535
A78706Align
A78707
Main GearSub Gear
Service Bolt
A78708
101
2
3
4
5
6
7
89
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-43
2135 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
26. REMOVE WATER PUMP ASSY
(a) Remove the 3 bolts and 3 nuts, then remove the water
pump and gasket.
27. REMOVE CAMSHAFT
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being removed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Align the timing marks (2 dot marks) of the camshaft drive
and driven gears by turning the camshaft with a wrench.
(b) Secure the exhaust camshaft sub gear to the main gear
with a service bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
Recommended service bolt
Thread diameter6 mm
Thread pitch1.0 mm
Bolt length16 to 20 mm
HINT:
When removing the camshaft, make certain that the torsional
spring force of the sub gear has been eliminated by installation
of the service bolt.
(c) Using several steps, loosen and remove the 10 bearing
cap bolts uniformly in the sequence shown in the illustra-
tion. Remove the 5 bearing caps and camshaft.
NOTICE:

Do not pry out the camshaft.

Be careful not to damage the contact surface of the
cylinder head that receives the shaft thrust.

A78709
10
1
2
3
4
5
67
8
9
A78710Align
A78711Main GearSub Gear
Service Bolt 14-44
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2136 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
28. REMOVE NO.2 CAMSHAFT
(a) Using several steps, loosen and remove the 10 bearing
cap bolts uniformly in the sequence shown in the illustra-
tion. Remove the 5 bearing caps and No. 2 camshaft.
NOTICE:

Do not pry out the camshaft.

Be careful not to damage the contact surface of the
cylinder head that receives the shaft thrust.
(b) Remove the oil seal from the No. 2 camshaft.
29. REMOVE NO.3 CAMSHAFT SUB-ASSY
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being removed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Align the timing marks (1 dot marks) of the camshaft drive
and driven gears by turning the camshaft with a wrench.
(b) Secure the exhaust camshaft sub gear to the main gear
with a service bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
Recommended service bolt
Thread diameter6 mm
Thread pitch1.0 mm
Bolt length16 to 20 mm
HINT:
When removing the camshaft, make certain that the torsional
spring force of the sub gear has been eliminated by installation
of the service bolt.

A78722
SST
A78723
SST
A78724
Seal Width 2 to 3 mm (0.08 to 0.12 in.)
A
A
B
B
A78754
SST
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-53
2145 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
56. INSTALL SPARK PLUG TUBE GASKET
(a) Using SST and a hammer, tap in the new gasket until its
surface is flush with the upper edge of the cylinder head
cover.
SST 09950- 60010 (09951- 00430), 09950- 70010
(09951-07100)
(b) Return the ventilation plate tab to its original position.
(c) Apply a light coat of multi-purpose grease to the gasket
lip.
57. INSTALL ENGINE REAR OIL SEAL
(a) Using SST and a hammer, tap in the new oil seal until its
surface is flush with the rear oil seal retainer edge.
SST 09223-15030, 09950-70010 (09951-07100)
NOTICE:

Be careful not to tap the oil seal at an angle.

Keep the lip free of foreign objects.
(b) Apply multi-purpose grease to the oil seal lip.
58. INSTALL ENGINE REAR OIL SEAL RETAINER
(a) Remove any old packing material from the contact sur-
face.
(b) Apply a continuous bead of seal packing (Diameter 2 to
3 mm (0.08 to 0.12 in.)) as shown in the illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:

Remove any oil from the contact surface.

Install the oil seal retainer within 3 minutes after ap-
plying seal packing.

Do not expose the seal packing to engine oil within 2
hours after installing.
(c) Install the oil seal retainer with the 6 bolts. Tighten the
bolts uniformly in several steps.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
59. INSTALL OIL PUMP SEAL
(a) Using SST and a hammer, tap in the new oil seal until its
surface is flush with the oil pump body edge.
SST 09223-00010
NOTICE:

Be careful not to tap the oil seal at an angle.

Keep the lip free of foreign objects.
(b) Apply multi-purpose grease to the oil seal lip.