2005 LEXUS ES300 torque spec

550DG-02
- HEATER & AIR CONDITIONERCOOLER CONDENSER ASSY
55-43
2658 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
COOLER CONDENSER ASSY
ON-VEHICLE INSPECTION
1. INSPECT COOLER CONDENSER ASSY
(a) If a fin of the cooler condenser assy is dirty, clean it with water and dry it with compressor air.
NOTICE:
Do not damage the fin of the condenser assy.
(b) If a fin of the condenser assy is bent, make it straight using a screwdriver or pliers.
2. INSPECT CONDENSER FOR LEAKAGE OF REFRIGERANT
(a) Using a halogen leak detector, check pipe joints for gas leakage.
(b) If gas leakage is detected in a joint, check the torque of the joint.

550DH-02
I31635
Radiator Support Upper
O-ring

Cooler Condenser Assy
Cooler Dryer
Filter
Cap
9.8 (100, 85 in.Vlbf)
Non-reusable parts Compressor oil ND-OIL 8 or equivalent
9.8 (100, 85 in.Vlbf)
O-ring
5.4 (55, 47 in.Vlbf)
O-ring

12 (125, 9)


Air Cleaner Inlet No. 1
Air Cleaner Inlet Assy
NVm (kgfVcm, ftVlbf): Specified torque
Radiator Lower Air Deflector
Hood Lock Release Lever
Protector
55-44
- HEATER & AIR CONDITIONERCOOLER CONDENSER ASSY
2659 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
COMPONENTS

0103A-07
D25697

Oil Seal

O-ring
Oil Pump Drive Gear
Oil Pump Driven Gear
Stator Shaft Assy
x13
10 (100, 7)
Oil Seal Ring
N´m (kgf´cm, ft´lbf): Specified torque

Non-reusable part
- INTRODUCTIONHOW TO USE THIS AUTOMATIC TRANSAXLE REPAIR
MANUAL01-1
1 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
HOW TO USE THIS AUTOMATIC TRANSAXLE REPAIR
MANUAL
GENERAL INFORMATION
1. GENERAL DESCRIPTION
(a) This manual is made in accordance with SAE J2008.
(b) Generally repair operations can be separated in the following 3 main processes:
1. Diagnosis
2. Removing and Installing, Replacing, Disassembling, Installing and Checking, Adjusting
3. Final Inspection
(c) This manual explainsº Removing and Installing, Replacing,
Disassembling ,Instaling and Checking,
Adjustingº , butº Final inspectionº is omitted.
(d) The following essential operations are not written in this manual, however these operations must be
done in the practical situation.
(1) Operation with a jack or lift
(2) Cleaning of a removed part when necessary
(3) Visual check
2. INDEX
(a) An alphabetical INDEX is provided as a section on the end of the book to guide you to the item to be
repaired.
3. PREPARATION
(a) Use of special service tools (SST) and special service materials (SSM) may be required, depending
on the repairing condition. Be sure to use SST and SSM when they are required and follow the working
procedure properly. A list of SST and SSM is in the Preparation section of this manual.
4. REPAIR PROCEDURES
(a) Component drawing is placed as the section or title when necessary.
(b) Illustrations of the parts catalog are placed as theº disassembled parts drawingº so that it enables you
to understand the fitting condition of the components.
(c) Non-reusable parts, grease applied parts, precoated parts and tightening torque are specified in the
components drawing.
Example:

Illustration:
what to do and whereTask heading: what to do
Detailed text:
how to do task
Set part No.Component part No.
87. INSTALL FR DIFFERENTIAL CASE FRONT TAPERED
ROLLER BEARING
(a) Using SST and a press, install the front differential case
tapered roller bearing front inner race to the differential
case.
SST 09316-60011 (09316-00011)
Illustration:
what to do and whereTask heading: what to do
Detailed text:
how to do task
Set part No.Component part No.
87. INSTALL FR DIFFERENTIAL CASE FRONT TAPERED
ROLLER BEARING
(a) Using SST and a press, install the front differential case
tapered roller bearing front inner race to the differential
case.
SST 09316-60011 (09316-00011)
D26831
01-2- INTRODUCTIONHOW TO USE THIS AUTOMATIC TRANSAXLE REPAIR
MANUAL
2 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(d) Tightening torque, oil applying position, and non-reusable parts are described as important points in
the procedure.
NOTICE:
There are cases where such information can only be indicated by an illustration. In that case, all the
information such as torque, oil, etc are described in the illustration.
(e) Installing procedure of operation item is performed in the reverse order of the removing, and only the
important points are described.
(f) Only items with points are described in the procedure, and the operational portion and content are
placed using an illustration. In the explanations, details of the operational method, standard value and
notice are placed.
(g) There may be a case where the illustrations of similar models are used. In that case the details may
be different from the actual vehicle.
(h) The procedures are presented in a step-by-step format:
(1) The illustration shows what to do and where to do it.
(2) The task heading tells what to do.
(3) The detailed text tells how to perform the task and gives other information such as specifications
and warnings.
Example:
HINT:
This format provides an experienced technician with a FAST TRACK to the necessary information. The task
heading can be read at a glance when necessary, and the text below provides detailed information. Impor-
tant specifications and warnings always stand out in bold type.
5. SERVICE SPECIFICATIONS
(a) Specifications are presented in bold type throughout the manual. You never have to leave the proce-
dure to look up your specifications. The specifications are also found in the Service Specifications sec-
tion for a quick reference.
6. TERMS DEFINITION
CAUTIONIndicate the possibility of injury to you or other people.
NOTICEIndicate the possibility of damage to the components being repaired.
HINTProvide additional information to help you perform the repair efficiently.

0103B-07
Z11554
Seal Lock Adhesive 01-4
- INTRODUCTIONREPAIR INSTRUCTION FOR AUTOMATIC
TRANSAXLE REPAIR MANUAL
4 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
REPAIR INSTRUCTION FOR AUTOMATIC TRANSAXLE
REPAIR MANUAL
PRECAUTION
1. BASIC REPAIR HINT
(a) PRECOATED PARTS
(1) Precoated parts are bolts, nuts, etc. that are coated
with a seal lock adhesive at the factory.
(2) If a precoated part is retightened, loosened or
caused to move in any way, it must be recoated with
the specified adhesive.
(3) When reusing precoated parts, clean off the old
adhesive and dry with compressed air. Then apply
the specified seal lock adhesive to the bolt, nut or
threads.
NOTICE:
Do the torque checking with the lower limit value of the torque tolerance.
(4) Depending on the seal lock agent to apply, there may be a case where it is necessary to leave
it for a specified time until it hardens.
(b) GASKETS
When necessary, use a sealer on gaskets to prevent leaks.
(c) BOLTS, NUTS AND SCREWS
Carefully observe all specifications for bolt tightening torques. Always use a torque wrench.

L1 L2L1 L2
D02612
L2 L1L2 L1
D01201
L2 L1L2 L1
D01202
- INTRODUCTIONREPAIR INSTRUCTION FOR AUTOMATIC
TRANSAXLE REPAIR MANUAL01-5
5 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(d) TORQUE WHEN USING EXTENSION TOOL WITH
TORQUE WRENCH
(1) In case of tightening by extending the entire length
of the torque wrench combined with SST or tool, if
you tighten until the reading of the torque wrench
reached the specified torque value, the actual
torque becomes excessive.
(2) In this text, only the specified torque is described.
In case of using SST or extension tool, find the read-
ing of the torque wrench by the formula.
(3) Formula T'=T x L2/(L1 + L2)
T'Reading of torque wrench {NVm (kgfVcm, ftVlbf)}
TTorque {NVm (kgfVcm, ftVlbf)}
L1Length of SST or tool (cm)
L2Length of torque wrench (cm)

030JL-02
V00079
ClassDiameter
mmPitch
mmSpecified torque
Hexagon head bolt
Hexagon flange bolt
N´m kgf´cm
ft´lbf N´mkgf´cm
ft´lbf
in.´lbf
in.´lbf
in.´lbfin.´lbf
in.´lbf
in.´lbf 03-2
- SERVICE SPECIFICATIONSSTANDARD BOLT FOR AUTOMATIC TRANSAXLE
REPAIR MANUAL
18 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
SPECIFIED TORQUE FOR STANDARD BOLTS

03-6
- SERVICE SPECIFICATIONSAUTOMATIC TRANSMISSION / TRANSAXLE
22 Author
: Date
:
U151E, U151F A/T REPAIR MANUAL (RM1021U) U/D planetary gear
Preload (at 60 rpm)0.50 - 1.42 NVm (5.1 - 14.5 kgfVcm, 0.06 - 0.17 in.Vlbf)
Front planetary gear
Turning torque (at 60 rpm) New Bearing
Used Bearing0.51 - 1.02 NVm (5.1 - 10.0 kgfVcm, 4.4 - 8.7 in.Vlbf)
0.26 - 0.51 NVm (2.7 - 5.2 kgfVcm, 2.3 - 4.5 in.Vlbf)
Input shaft
End play0.262 - 1.249 mm (0.0103 - 0.0492 in.)
Transaxle rear cover
Bearing press fit depth20.55 - 21.25 mm (0.8091 - 0.8366 in.)
Transmission valve body
Valve body installation bolt length A
B
C41 mm (1.614 in.)
57 mm (2.244 in.)
25 mm (0.984 in.)
Accumulator
SpringFree length/Outer diameterColor
B3Inner
Outer62.00 (2.4409) / 15.50 (0.610)
74.23 (2.9224) / 16.50 (0.649)Purple
Purple
C260.96 (2.3999) / 14.10 (0.555)Yellow
C372.20 (2.8425) / 19.0 (0.748)Colorless
Front differential(U151E)
Backlash0.05 - 0.20 mm (0.0020 - 0.0079 in.)
Thrust washer thickness Mark
-
-
-
1.625 mm (0.0640 in.)
1.725 mm (0.0679 in.)
1.825 mm (0.0719 in.)
Praload (at 60 rpm) New bearing
Used bearing0.20 - 0.69 NVm (2.0 - 7.0 kgfVcm, 1.8 - 6.1 in.Vlbf)
0.10 - 0.35 NVm (1.0 - 3.6 kgfVcm, 0.9 - 3.1 in.Vlbf)
Flange thickness Mark
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
G
H
2.00 mm (0.0787 in.)
2.05 mm (0.0807 in.)
2.10 mm (0.0827 in.)
2.15 mm (0.0846 in.)
2.20 mm (0.0866 in.)
2.25 mm (0.0886 in.)
2.30 mm (0.0906 in.)
2.35 mm (0.0925 in.)
2.40 mm (0.0945 in.)
2.45 mm (0.0965 in.)
2.50 mm (0.0984 in.)
2.55 mm (0.1004 in.)
2.60 mm (0.1024 in.)
2.65 mm (0.1043 in.)
2.70 mm (0.1063 in.)
2.75 mm (0.1083 in.)
2.80 mm (0.1102 in.)
2.85 mm (0.1122 in.)
Front differential (U151F)
Side gear backlash0.05 - 0.20 mm (0.0020 - 0.0079 in.)