2005 INFINITI QX4 engine

ATC-192
REFRIGERANT LINES
Revision: October 20052005 QX56
NOTE:
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with
water or dirt that may be in the drain hose.
5. If a leak is detected, verify at least once by blowing compressed air into the area of the suspected leak,
then repeat the leak check.
6. Do not stop when one leak is found. Continue to check for additional leaks at all system components and
connections.
7. If no leaks are found, perform steps 8 - 11.
8. Start the engine.
9. Set the heater A/C controls as follows:
NOTE:
For the automatic system, turn OFF the automatic controls and set the heater A/C controls manually.
a. A/C switch to ON
b. Air flow to VENT mode
c. Intake position to RECIRCULATION mode
d. Temperature to MAX cold
e. Blower speed to HIGH
10. Run the engine at 1,500 rpm for at least 2 minutes.
11. Turn the engine OFF and perform the leak check again following
steps 4 through 6 above.
Refrigerant leaks should be checked immediately after turning
the engine OFF. Begin with the leak detector at the compressor.
The pressure on the high pressure side will gradually drop after
the refrigerant circulation stops and pressure on the low pres-
sure side will gradually rise, as shown in the graph. Some leaks
are more easily detected when the pressure is high.
12. Before connecting the recovery/recycling recharging equipment to the vehicle, check the recovery/recy-
cling recharging equipment gauges. No refrigerant pressure should be displayed. If pressure is displayed,
recover the refrigerant from the equipment lines and then check the refrigerant purity.
13. Confirm refrigerant purity in supply tank using recovery/recycling recharging equipment and refrigerant
identifier equipment (J-41810-NI).
14. Confirm the refrigerant purity in the vehicle's A/C system using recovery/recycling recharging equipment
and refrigerant identifier equipment (J-41810-NI).
15. Discharge the A/C system using recovery/recycling recharging equipment. Repair the leaking fitting or
component as necessary.
16. Evacuate and recharge the A/C system and perform the leak test to confirm that there are no refrigerant
leaks.
17. Conduct the Operational Check to ensure system works properly. Refer to AT C - 5 7 , "
Operational Check
(Front)" and ATC-60, "Operational Check (Rear)" .
SHA8 39 E

SERVICE DATA AND SPECIFICATIONS (SDS)
ATC-193
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: October 20052005 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Service Data and Specifications (SDS)EJS003Z9
COMPRESSOR
LUBRICANT
REFRIGERANT
ENGINE IDLING SPEED
Refer to EC-77, "Idle Speed and Ignition Timing Check" .
BELT TENSION
Refer to EM-12, "Checking Drive Belts" .
MakeZEXEL VALEO CLIMATE CONTROL
ModelDKS-17D
Typ eSwash plate
Displacement
175.5 cm
3 (10.7 in3 ) / revolution
Cylinder bore × stroke 30.5 mm (1.20 in) x 24.0 mm (0.94 in)
Direction of rotation Clockwise (viewed from drive end)
Drive beltPoly V
MakeZEXEL VALEO CLIMATE CONTROL
ModelDKS-17D
NameNISSAN A/C System Lubricant Type S
Capacity
290 m (9.8 US fl oz, 10.2 Imp fl oz)
Typ eHFC 134a (R-134a)
Capacity1.08 ± 0.05 kg (2.38 ± 0.11 oz)

AV-2Revision: October 20052005 QX56 “VIEW” MODE ..................................................... 70
“HEADING” MODE .............................................. 71
“NEARBY DISPLAY ICONS” MODE ................... 71
“SAVE CURRENT LOCATION” MODE ............... 71
“ADJUST CURRENT LOCATION” MODE ........... 71
“AUTO RE-ROUTE” MODE ................................. 72
“AVOID AREA SETTINGS” MODE ...................... 72
“CLEAR MEMORY” MODE ................................. 72
“EDIT ADDRESS BOOK” MODE ........................ 73
“GPS INFORMATION” MODE ............................. 73
“QUICK STOP CUSTOMER SETTING” MODE ... 73
“SET AVERAGE SPEED” MODE ........................ 73
“TRACKING” MODE ............................................ 74
GUIDANCE VOLUME ......................................... 74
DISPLAY WITH PUSHED “TRIP” BUTTON ........ 74
TRIP 1 OR TRIP 2 ............................................... 75
FUEL ECONOMY ................................................ 75
MAINTENANCE .................................................. 75
ENGINE OIL OR TIRE ROTATION ..................... 75
TIRE PRESSURE ................................................ 76
WARNING INDICATIONS ................................... 76
CAN Communication System Description .............. 76
Component Parts Location ..................................... 77
Schematic ............................................................... 78
Wiring Diagram — NAVI — ..................................... 79
Schematic ............................................................... 86
Wiring Diagram — COMM — ................................. 87
Terminals and Reference Value for NAVI Control
unit .......................................................................... 90
Terminals and Reference Value for Display Control
unit .......................................................................... 92
Terminals and Reference Value for Display unit ..... 96
Terminals and Reference Value for AV Switch ....... 98
Terminals and Reference Value for BCM ................ 99
On Board Self-Diagnosis Function .......................101
DESCRIPTION ..................................................101
DIAGNOSIS ITEM .............................................101
Self-Diagnosis Mode (DCU) .................................101
OPERATION PROCEDURE ..............................101
SELF–DIAGNOSIS RESULT .............................103
Self-Diagnosis Mode (NAVI) .................................104
OPERATION PROCEDURE ..............................104
SELF–DIAGNOSIS RESULT .............................105
Confirmation/Adjustment Mode ............................107
OPERATION PROCEDURE ..............................107
DISPLAY DIAGNOSIS .......................................108
VEHICLE SIGNALS ...........................................108
NAVIGATION .....................................................109
DISPLAY DIAGNOSIS .......................................109
VEHICLE SIGNALS ...........................................110
HISTORY OF ERRORS ....................................110
DIAGNOSIS BY HISTORY OF ERRORS ..........110
NAVIGATION .....................................................112
CAN DIAG SUPPORT MONITOR ........................114
OPERATION PROCEDURE ..............................114
AV Switch Self-Diagnosis Function .......................115
Power Supply and Ground Circuit Check for NAVI
Control Unit ...........................................................116
Power Supply and Ground Circuit Check for Display Control Unit ...........................................................117
Power Supply and Ground Circuit Check for Display
Unit ........................................................................118
Power Supply and Ground Circuit Check for AV
Switch ................................................................... 120
Vehicle Speed Signal Check for NAVI Control Unit . 121
Vehicle Speed Signal Check for Display Control Unit . 122
Illumination Signal Check for NAVI Control Unit ... 123
Illumination Signal Check for Display Control Unit . 123
Ignition Signal Check for NAVI Control Unit .......... 123
Ignition Signal Check for Display Control Unit ...... 124
Reverse Signal Check for NAVI Control Unit ........ 124
Reverse Signal Check for Display Control Unit .... 124
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) ...................... 125
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) .......................... 126
Display Communication Line Check (Between Dis-
play Control Unit and Display Unit) ....................... 128
AV Communication Line Check (Between Display
Control Unit and AV Switch) .................................. 130
CAN Communication Line Check ......................... 131
If NAVI Control Unit Detects That DVD-ROM Map
is Not Inserted ....................................................... 131
If NAVI Control Unit Detects That Inserted DVD-
ROM Map is Malfunctioning or If It is Impossible to
Load Data from DVD-ROM Map ........................... 131
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning ..................................... 132
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen ..................... 132
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Bluish) ............................................ 134
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Reddish) ......................................... 135
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Yellowish) ....................................... 136
Color of RGB Image is Not Proper (All Screen Looks
Bluish) ................................................................... 137
Color of RGB Image is Not Proper (All Screen Looks
Reddish) ................................................................ 138
Color of RGB Image is Not Proper (All Screen Looks
Yellowish) .............................................................. 139
NAVI Screen is Rolling .......................................... 140
Guide Sound is Not Heard .................................... 142
Screen is Not Shown ............................................ 143
A/C Screen is Not Shown (NAVI Screen is Shown) . 143
FUEL ECONOMY Screen is Not Shown ............... 143
Average Fuel Economy Displayed is Not Shown (“
*** ” is Shown) ....................................................... 143
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) .............................................................. 144
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ....................................... 144
WARNING DOOR OPEN Screen is Not Shown ... 144
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ............................................. 145
Audio Does Not Work ........................................... 145
Navigation System Does Not Activate .................. 145

AUDIO
AV-29
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
NOTE:
1. The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.

Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.

Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the
antenna at a different time from the waves which reflect off mountains or buildings.
FOR CD ONLY
Noise InspectionEKS00BIH
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Symptom Possible cause
CD cannot be inserted.

CD

Audio unit CD cannot be ejected.
The CD cannot be played.
The sound skips, stops suddenly, or is distorted.
Occurrence condition Possible cause
Occurs only when engine is ON.A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.

Ignition components
A whistling noise occurs while the engine speed is
high. A booming noise occurs while the engine is
running and the lighting switch is ON.

Generator
The occurrence of the noise is linked with the operation of the fuel pump.

Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.A cracking or snapping sound occurs with the
operation of various switches.

Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing.

Motor case ground

Motor
The noise occurs constantly, not just under certain conditions.

Rear defogger coil malfunction

Open circuit in printed heater

Poor ground of antenna amplifier or
antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.

Ground wire of body parts

Ground due to improper part installation

Wiring connections or a short circuit

NAVIGATION SYSTEM
AV-67
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Display with Pushed “SETTING” button
The function of each icon is as follows:
Display Settings
How To Perform Display Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “Display” with "ENTER" button.
Application Items
Brightness/Contrast/Map Back ground
How To Perform Navigation Setting
1. Select “Brightness/Contrast/Map Background”.

Brightness, Contrast and Background are shown at the lower part of the screen, and it can be set with the
joystick.
Display Off
How To Perform Navigation Setting
1. Select “Display Off”.

When setting is turned on (Indicator light ON), the display will be under sleep mode.
SKIA4496E
Icon Description
Display Settings of display can be performed.
Vehicle Electronic Systems Settings of vehicle electrical equipment can be performed.
System Settings Settings of linguistic select, time adjusting and beep sound can be performed.
Navigation Settings and adjusting of navigation can be performed.
Short Menus Easy Mode and Expert Mode can be switched.
Guidance Volume The volume and/or on/off of voice prompt can be controlled by the joystick.
Help (only easy mode) Explanation of navigational functions appear on the display.
SKIA5791E
Icon DescriptionReference
page
Brightness/Contrast/Map Background Brightness, Contrast and Map Background can be set.AV- 6 7
Display Off Display sleep mode ON/OFF can be switched.AV- 6 7
Setting of the under section display The setting status of A/C or AV can be shown. AV- 6 8

AV-68
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Setting of the under section display
How To Perform Under Section Display Setting
1. Select “Setting of the Under Section Display”.

The setting status that is selected from A/C or AV is shown at the lower part of the screen.
Vehicle Electronic Systems
Application Items
How To Perform Navigation Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “Vehicle Electronic Systems”.
System Settings
How To Perform System Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “System Settings”.
Icon Description
Adjust Driver Seat When Exiting Vehicle The driver's seat automatically moves back and returns to the original position.
Lift Steering Column When Exiting Vehicle The steering column automatically tilts up and returns to the original position.
Remote Unlock Driver's Door FirstThis option allows selection of which doors will unlock first during an unlocking oper-
ation.
Keyless Remote Response — HornThis option allows the horn chirp mode when pressing the LOCK or UNLOCK button
on the keyfob to be changed.
Keyless Remote Response — LightsThis option allows the hazard flash mode when pressing the LOCK or UNLOCK but-
ton on the keyfob to be changed.
Auto Re-Lock Time This option allows the length of time before doors auto re-lock to be set.
Sensitivity of Automatic Headlights This option allows the sensitivity of the autolights to be set.
Automatic Headlights Off Delay This option allows the length of time before the autolights turn off to be set.
Speed Dependent Wiper This option allows the driving speed dependent wiper function to be turned on or off.
Return All Settings to Default All settings will return to the initial conditions.
WKIA1802E
SKIA4536E

AV-70
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Navigation Setting
How To Perform Navigation Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “NAVIGATION”.
Application Items
*: Not displayed in Easy Mode.
“VIEW” MODE
1. Select “Birdview™” or “Plan View” icon.

To open the map screen display with Birdview™, select “Bird-
view™”.

To open the map screen display with Plan View, select “Plan
View”.
SKIA0551E
Icon DescriptionReference
page
View Map display mode can be switched.AV- 7 0
HeadingHeading of the map display can be customized for either north heading or the
actual driving direction of the vehicle.AV- 7 1
Nearby Display Icons*Icons of facilities can be displayed.
Facilities to be displayed can be selected from the variety selections.AV- 7 1
Save Current Location* Current vehicle location can be registered in Address Book.AV- 7 1
Adjust Current Location*Current location of position marker can be adjusted. Direction of position marker
also can be calibrated when heading direction of the vehicle on the display is
not matched with the actual direction.AV- 7 1
Auto Re-route On/Off* ON/OFF of Auto Re-route can be switched.AV- 7 2
Avoid Area Setting* A particular area can be avoided when routing.AV- 7 2
Clear Memory* Address Book, Previous destination or Avoid area can be deleted.AV- 7 2
Edit Address Book* Address Book can be edited.AV- 7 3
GPS Information*The GPS data includes longitude, latitude and altitude (distance above sea
level) of the present vehicle position, and current date and time for the area in
which the vehicle is being driven.
Also indicated are the GPS reception conditions and the GPS satellite position.AV- 7 3
Quick Stop Customer Setting* One facility of your selection can be added to your Quick Stop.AV- 7 3
Set Average Speed for Estimated
Journey Time*Average vehicle speed can be set to calibrate estimated journey time for the
destination.AV- 7 3
Tracking On/Off* Tracking to the present vehicle position can be displayed.AV- 7 4
SKIA0554E

AV-74
NAVIGATION SYSTEM
Revision: October 20052005 QX56
“TRACKING” MODE

To delete the tracking marks on the map, select “Off”.

To leave the tracking marks on the map, select “On”.
NOTE:
When a trail display is turned OFF, trail data is erased from the mem-
ory.
GUIDANCE VOLUME
Description
Following guidance volume settings can be changed.
Activation/Deactivation Setting

The voice prompt can be turned on/off by pressing the “Guidance Volume” button.
Voice Volume Setting

Volume of the voice can be controlled by tilting the joystick to left/right.
DISPLAY WITH PUSHED “TRIP” BUTTON

When the “TRIP” button is pushed, the following items will display on the screen.

Warning message (if there are any) →TRIP 1→TRIP 2→FUEL ECONOMY→MAINTENANCE→OFF.
SKIA0559E
SKIA4497E
Display items Display/Setting contentsReference
page
Trip 1 or Trip 2Elapsed TimeDisplays driving time with a range of 0000:00:00 to
9999:59:59.
AV- 7 5
Driving Distance
[(km) or (miles)] Displays driving distance with a range of 00000.0 to
99999.9.
Average speed
[(km/h) or (MPH)]Displays average speed with a range of 000.0 to 999.9.
Fuel EconomyAverage Fuel Economy
[(MPG) or (l/100km)]Displays fuel economy with ignition switch ON, average
fuel economy each 30 seconds.
AV- 7 5
Distance to Empty
[(km) or (miles)]Displays possible driving distance with remaining fuel.
Fuel Economy [(MPG)
or (l/100km)]Displays fuel economy each approx. 100 ms.
Maintenance Engine oilMaintenance intervals of engine oil and setting of oil
change cycle.
AV- 7 5
Tire rotationMaintenance intervals of tire and setting of tire replace-
ment cycle.
Tire pressure Tire pressure displayed as tire pressure information.