2005 INFINITI QX4 sensor

AT-234
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
16. Disconnect TCM connectors.
CAUTION:
Be careful not to damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using flat blade screwdriver.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Be careful not to damage connectors.
SCIA5264E
SCIA5155E
SCIA5447E
SCIA5448E
SCIA5449E

AT-236
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
5. Install A/T fluid temperature sensor 2 to bracket.
6. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to AT-250, "
Components" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
7. Install control valve with TCM in transmission case.
CAUTION:

Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.

Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.

Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.

Assemble it so that manual valve cutout is engaged with
manual plate projection.
SCIA5264E
SCIA5301E
SCIA5034E
SCIA5142E

ON-VEHICLE SERVICE
AT-237
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
8. Install bolts A, B and C in control valve with TCM.
9. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1 → 2 → 3), and then tighten other
bolts.
10. Tighten control valve with TCM bolts to the specified torque.
Refer to AT- 2 5 0 , "
Components" .
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5139E
SCIA5140E
SCIA5023E
SCIA5446E

AT-238
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clips.
15. Install oil pan to transmission case, refer to AT-229, "
Installation" .
16. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Pour ATF into transmission assembly. Refer to MA-24, "
Chang-
ing A/T Fluid" .
20. Connect the negative battery terminal
SCIA5024E
SCIA3969E
SCIA5038E
SCIA5039E

ON-VEHICLE SERVICE
AT-239
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Remove oil pan and oil pan gasket, refer to AT - 2 2 9 , "
Removal" .
3. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
4. Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
5. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
6. Remove bracket from A/T fluid temperature sensor 2.
SCIA5023E
SCIA5146E
SCIA5253E
SCIA5264E

AT-240
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
Installation
CAUTION:
After completing installation, check for A/T fluid leakage and fluid level. Refer to MA-24, "
Changing A/
T Fluid" , MA-22, "Checking A/T Fluid" .
1. Install A/T fluid temperature sensor 2 to bracket.
2. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 mount-
ing bolt to the specified torque. Refer to AT- 2 5 0 , "
Components" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
3. Connect A/T fluid temperature sensor 2 connector.
4. Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5. Install oil pan to transmission case, refer to AT-229, "
Installation" .
6. Connect the negative battery terminal
SCIA5264E
SCIA5253E
SCIA5023E
SCIA5146E

AT-244
TRANSMISSION ASSEMBLY
Revision: October 20052005 QX56
TRANSMISSION ASSEMBLYPFP:31020
Removal and Installation (4x2)ECS00CL0
COMPONENTS
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1. Disconnect the negative battery terminal.
2. Remove engine cover.
3. Remove A/T fluid indicator gauge.
4. Remove engine under cover with power tool.
5. Remove exhaust front tube and center muffler with power tool. Refer to EX-4, "
REMOVAL" .
6. Remove rear propeller shaft. Refer to PR-9, "
REMOVAL" .
7. Remove A/T control cable. Refer to AT-228, "
REMOVAL" .
1. A/T fluid indicator pipe 2. A/T fluid indicator 3. O-ring
4. Transmission assembly 5. Fluid cooler tube 6. A/T cross member
7. Insulator 8. Copper washers
LCIA0354E

TRANSMISSION ASSEMBLY
AT-245
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
8. Remove crankshaft position sensor (POS) from A/T assembly.
9. Remove fluid cooler tube.
10. Remove dust cover from converter housing part.
11. Secure drive plate using Tool then remove drive plate to torque
converter bolts.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
NOTE:
Tool must be removed and drive plate turned to access all drive
plate to torque converter bolts.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
13. Remove cross member with power tool.
14. Remove air breather hose. Refer to AT-242, "
Removal and Installation" .
15. Disconnect A/T assembly connector.
16. Remove A/T fluid indicator pipe from A/T assembly.
17. Plug up openings such as the A/T fluid indicator pipe hole, etc.
18. Remove the A/T assembly to engine bolts with power tool.
19. Remove A/T assembly from vehicle using Tool and a transmis-
sion jack.
CAUTION:

Secure torque converter to prevent it from dropping.

Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter

After inserting a torque converter to a transmission, be sure to
check dimension A to ensure it is within the reference value
limit.
LCIA0334E
Tool number : — (J-47245)
LCIA0335E
SCIA0499E
Dimension A : 24.0 mm (0.94 in) or more
SAT0 1 7B