2005 INFINITI QX4 sensor

DISASSEMBLY
AT-273
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
44. Remove parking gear from output shaft.
45. Remove seal rings from output shaft.
46. Remove needle bearing from transmission case.
47. Remove revolution sensor from transmission case.
CAUTION:

Do not subject it to impact by dropping or hitting it.

Be careful not to damage harness with the edge of case.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
48. Remove reverse brake snap ring (fixing plate) using 2 flat-
bladed screwdrivers.
NOTE:
Press out snap ring from the transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using another
screwdriver.
49. Remove reverse brake retaining plate from transmission case.
SCIA5247E
SCIA5209E
SCIA5213E
SCIA2320E
SCIA5032E

ASSEMBLY
AT-303
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
22. Measure clearance between retaining plate and snap ring. If not
within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:

Take care with the direction of needle bearing. Refer to
AT-260, "
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings" .

Apply petroleum jelly to needle bearing.
24. Install revolution sensor to transmission case. Tighten revolution
sensor bolt to the specified torque. Refer to AT-250, "
Compo-
nents" .
CAUTION:

Do not subject it to impact by dropping or hitting it.

Be careful not to damage harness with the edge of case.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
25. Install new rear oil seal into the rear extension (2WD models) or
adapter case (4WD models) until it is flush with component face,
using Tool or suitable drift.
CAUTION:

Apply ATF to rear oil seal.

Do not reuse rear oil seal.Specified clearance “A”:
Standard: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate:
Refer to AT-323, "
Reverse brake" .
SCIA5341E
SCIA5213E
SCIA2320E
SCIA5581E

ASSEMBLY
AT-315
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
5. Tighten oil pump bolts to specified torque. Refer to AT-250,
"Components" .
CAUTION:
Apply ATF to oil pump bushing.
6. Install new O-ring to input clutch assembly.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
7. Install converter housing to transmission case.
CAUTION:
Do not reuse self-sealing bolt.
8. Make sure that brake band does not close turbine revolution
sensor hole.
9. Install control valve with TCM.
a. Install A/T fluid temperature sensor 2 to bracket.
SCIA2300E
SCIA5 011 E
Converter housing
bolt: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt : 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5171E
SCIA5034E
SCIA5264E

AT-316
ASSEMBLY
Revision: October 20052005 QX56
b. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to AT-250, "
Components" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
c. Install new O-ring to A/T assembly harness connector.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
d. Connect TCM connector and park/neutral position switch con-
nector.
e. Install A/T assembly harness connector to control valve with
TCM.
f. Connect TCM connectors.
SCIA5301E
SCIA5155E
SCIA5449E
SCIA5450E
SCIA5447E

ASSEMBLY
AT-317
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
g. Install control valve with TCM in transmission case.
CAUTION:

Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.

Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.

Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.

Assemble it so that manual valve cutout is engaged with
manual plate projection.
h. Install bolts A, B and C to control valve with TCM.
i. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1 → 2 → 3), and then tighten other
bolts.
j. Tighten control valve with TCM bolts to the specified torque.
Refer to AT- 2 5 0 , "
Components" .
10. Connect A/T fluid temperature sensor 2 connector.
SCIA5034E
SCIA5035E
Bolt symbol Length: mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5025E
SCIA5037E
SCIA5023E

AT-318
ASSEMBLY
Revision: October 20052005 QX56
11. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
12. Connect revolution sensor connector.
13. Securely fasten revolution sensor harness with terminal clips.
14. Pull down A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
15. Install snap ring to A/T assembly harness connector.
SCIA5446E
SCIA5024E
SCIA5293E
SCIA5299E
SCIA5300E

AT-322
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: October 20052005 QX56
Vehicle Speed When Performing and Releasing Complete Lock-upECS00CLH

At closed throttle, the accelerator opening is less than 1/8 condition.

At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed When Performing and Releasing Slip Lock-upECS00CLI

At closed throttle, the accelerator opening is less than 1/8 condition.
Stall SpeedECS0 0CL J
Line PressureECS00CLK
A/T Fluid Temperature SensorECS00CLL
Turbine Revolution SensorECS0 0CL M
Vehicle Speed Sensor A/T (Revolution Sensor)ECS00CLN
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
2.937Closed throttle 74 - 82 (46 - 51) 71 - 79 (45 - 49)
Half throttle 188 - 196 (117 - 122) 136 - 144 (85 - 90)
3.357Closed throttle 65 - 73 (41 - 46) 62 - 70 (39 - 44)
Half throttle 168 - 176 (105 - 110) 118 - 126 (74 - 79)
Final
gear
ratioThrottle position Gear positionVehicle speed km/h (MPH)
Slip lock-up “ON” Slip lock-up “OFF”
2.937 Closed throttle4th 52 - 60 (33 - 38) 49 - 57 (31 - 36)
5th 52 - 60 (33 - 38) 49 - 57 (31 - 36)
3.357 Closed throttle4th 46 - 54 (29 - 34) 43 - 51 (27 - 32)
5th 46 - 54 (29 - 34) 43 - 51 (27 - 32)
Stall speed2,500 - 2,800 rpm
Engine speedLine pressure [kPa (kg/cm2 , psi)]
R position D position
At idle speed 392 - 441 (4.0 - 4.5, 57 - 64) 373 - 422 (3.8 - 4.3, 54 - 61)
At stall speed 1,700 - 1,890 (17.3 - 19.3, 247 - 274) 1,310 - 1,500 (13.3 - 15.3, 190 - 218)
Name Condition CONSULT-II “DATA MONITOR” (Approx.) (V) Resistance (Approx.) (kΩ)
A/T fluid temperature sensor 10°C (32°F) 2.2 15
20°C (68°F) 1.8 6.5
80°C (176°F) 0.6 0.9
A/T fluid temperature sensor 20°C (32°F) 2.2 10
20°C (68°F) 1.7 4
80°C (176°F) 0.45 0.5
Name Condition Data (Approx.)
Turbine revolution
sensor 1When running at 50 km/h (31 MPH) in 4th speed with the closed throttle position switch
“OFF”.
1.3 (kHz)
Turbine revolution
sensor 2When moving at 20 km/h (12 MPH) in 1st speed with the closed throttle position switch
“OFF”.
Name Condition Data (Approx.)
Revolution sensor When moving at 20 km/h (12 MPH). 185 (Hz)

ATC-1
AUTOMATIC AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION AT C
A
B
AT C
Revision: October 20052005 QX56 PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Precautions for Working with HFC-134a (R-134a) ..... 5
Contaminated Refrigerant ........................................ 5
General Refrigerant Precautions .............................. 6
Precautions for Leak Detection Dye ......................... 6
A/C Identification Label ............................................ 7
Precautions for Refrigerant Connection ................... 7
FEATURES OF NEW TYPE REFRIGERANT
CONNECTION ...................................................... 7
O-RING AND REFRIGERANT CONNECTION ..... 8
Precautions for Servicing Compressor ....................11
Precautions for Service Equipment .........................11
RECOVERY/RECYCLING EQUIPMENT .............11
ELECTRONIC LEAK DETECTOR .......................11
VACUUM PUMP ................................................. 12
MANIFOLD GAUGE SET .................................... 12
SERVICE HOSES ............................................... 12
SERVICE COUPLERS ........................................ 13
REFRIGERANT WEIGHT SCALE ...................... 13
CHARGING CYLINDER ...................................... 13
Wiring Diagrams and Trouble Diagnosis ................ 13
PREPARATION ......................................................... 14
Special Service Tools ............................................. 14
HFC-134a (R-134a) Service Tools and Equipment ... 14
Commercial Service Tools ...................................... 17
REFRIGERATION SYSTEM ..................................... 18
Refrigerant Cycle ................................................... 18
REFRIGERANT FLOW ....................................... 18
Refrigerant System Protection ............................... 18
REFRIGERANT PRESSURE SENSOR ............. 18
PRESSURE RELIEF VALVE .............................. 19
Component Layout ................................................. 20
FRONT REFRIGERATION SYSTEM .................. 20
REAR REFRIGERATION SYSTEM .................... 21LUBRICANT .............................................................. 22
Maintenance of Lubricant Quantity in Compressor ... 22
LUBRICANT ........................................................ 22
CHECKING AND ADJUSTING ............................ 22
AIR CONDITIONER CONTROL ............................... 24
Description .............................................................. 24
Operation ................................................................ 24
AIR MIX DOORS CONTROL .............................. 24
BLOWER SPEED CONTROL ............................. 24
INTAKE DOOR CONTROL ................................. 24
MODE DOOR CONTROL ................................... 24
DEFROSTER DOOR CONTROL ........................ 24
MAGNET CLUTCH CONTROL ........................... 25
SELF-DIAGNOSTIC SYSTEM ............................ 25
Description of Control System ................................ 26
Control Operation ................................................... 26
DISPLAY SCREEN .............................................. 27
AUTO SWITCH ................................................... 27
TEMPERATURE CONTROL DIAL (TEMPERA-
TURE CONTROL) (DRIVER SIDE) ..................... 27
TEMPERATURE CONTROL DIAL (TEMPERA-
TURE CONTROL) (PASSENGER SIDE) ............ 27
TEMPERATURE CONTROL DIAL (TEMPERA-
TURE AND MODE CONTROL) (REAR) ............. 27
RECIRCULATION () SWITCH ............................. 27
DEFROSTER () SWITCH .................................... 27
REAR WINDOW DEFOGGER SWITCH ............. 27
OFF SWITCH ...................................................... 27
A/C SWITCH ....................................................... 27
MODE SWITCH (FRONT) ................................... 27
FRONT BLOWER CONTROL DIAL .................... 27
TEMPERATURE CONTROL DIAL (TEMPERA-
TURE AND MODE CONTROL) ........................... 28
REAR BLOWER CONTROL DIAL ...................... 28
Discharge Air Flow ................................................. 29
FRONT ................................................................ 29
REAR .................................................................. 29
System Description (Front) ..................................... 30
SWITCHES AND THEIR CONTROL FUNCTION ... 30
System Description (Rear) ..................................... 31