2005 INFINITI QX4 oil

QUICK REFERENCE CHART: QX562005

QUICK REFERENCE CHART: QX56PFP:00000
Engine Tune-Up DataELS001U4
Cylinder arrangementV- 8
Displacement
5,552 cm
3 (338.80 in3 )
Bore and stroke98 x 92 mm (3.86 x 3.62 in)
Valve arrangementDOHC
Firing order1-8-7-3-6-5-4-2
Number of piston ringsCompression 2
Oil 1
Number of main bearings5
Compression ratio9.8:1
Compression pressureStandard
1,520 kPa (15.5 kg/cm
2 , 220 psi) / 200 rpm
Minimum
1,324 kPa (13.5 kg/cm
2 , 192 psi) / 200 rpm
Differential limit between cylinders
98 kPa (1.0 kg/cm
2 , 14 psi) / 200 rpm
Cylinder number
Valve timing
Unit: degree
abcde f
232°230°2°48°3°49°
SEM957C
PBIC0187E

2005
QUICK REFERENCE CHART: QX56

Drive Belt Deflection and Tension
Spark Plugs (Double Platinum Tipped)
Front Wheel Alignment (Unladen*1 )*6ELS001U5
*1: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
*2: Target value 37° 31′ (37.52°)
*3: Target value 33° 59′ (33.98°)
*4: Target value 37° 44′ (37.73°)
*5: Target value 33° 29′ (33.48°)
*6: Some vehicles may be equipped with straight (non-adjustable) lower link bolts and washers. In order to adjust camber and caster on
these vehicles, first replace the lower link bolts and washers with adjustable (cam) bolts and washers.Tension of drive belts Auto adjustment by auto tensioner
MakeNGK
Standard typePLFR5A-11
Hot typePLFR4A-11
Cold typePLFR6A-11
Gap (nominal)1.1 mm (0.043 in)
Drive type4x2 4x4
Camber
Degree minute (decimal degree)Minimum -0° 51′ (-0.85°)-0° 33′ (-0.55°)
Nominal -0° 6′ (-0.10°)0° 12′ (0.20°)
Maximum 0° 39′ (0.65°)0° 57′ (0.95°)
Cross camber 0° 45′ (0.75°) or less 0° 45′ (0.75°) or less
Caster
Degree minute (decimal degree)Minimum 3° 15′ (3.25°)2° 45′ (2.75°)
Nominal 4° 0′ (4.00°)3° 30′ (3.50°)
Maximum 4° 45′ (4.75°)4° 15′ (4.25°)
Cross caster 0° 45′ (0.75°) or less 0° 45′ (0.75°) or less
Kingpin inclination
Degree minute (decimal degree)13° 32′ (13.53°)13° 13′ (13.22°)
Total toe-inDistance (A − B)Minimum 1.8 mm (0.07 in) 1.8 mm (0.07 in)
Nominal 2.8 mm (0.11 in) 2.8 mm (0.11 in)
Maximum 3.8 mm (0.15 in) 3.8 mm (0.15 in)
Angle (left side and right side)
Degree minute (decimal degree)Minimum 0° 3′ (0.05°)0° 3′ (0.05°)
Nominal 0° 5′ (0.08°)0° 5′ (0.08°)
Maximum 0° 7′ (0.12°)0° 7′ (0.12°)
Wheel turning angle
(full turn)Inside
Degree minute (decimal degree)34° 31′ – 38° 31′ *2
(34.52° – 38.52°)34° 44′ – 38° 44′ *4
(34.73° – 38.73°)
Outside
Degree minute (decimal degree)30° 59′ – 34° 59′ *3
(30.98° – 34.98°)30° 29′ – 34° 29′ *5
(30.48° – 34.48°)
SFA234AC

2005
QUICK REFERENCE CHART: QX56

Disc Brake - Repair LimitsELS001U8
Unit: mm (in)
Brake PedalELS001U9
Unit: mm (in)
Refill CapacitiesELS001UA
Brake model CLZ31VC (Front) AD14VE (Rear)
Brake PadStandard thickness (new) 11.88 (0.468) 12.13 (0.478)
Repair limit thickness 1.0 (0.039) 1.0 (0.039)
Disc rotorStandard thickness (new) 26.0 (1.024) 14.0 (0.551)
Repair limit thickness 24.5 (0.965) 12.0 (0.472)
Maximum uneven wear (measured at 8 positions) 0.015 (0.0006) 0.015 (0.0006)
Runout limit (with it attached to the vehicle) 0.04 (0.0016) 0.05 (0.0020)
Brake pedal height (from dash panel top surface) 182.3 − 192.3 (7.18 − 7.57)
Depressed pedal height [under a force of 490 N (50 kg, 110 lb) with engine running] More than 90.3 (3.55)
Clearance between stopper rubber and the threaded end of stop lamp switch 0.74 − 1.96 (0.029 − 0.077)
Pedal play3 − 11 (0.12 − 0.43)
DescriptionCapacity (Approximate)
Metric US measure Imp measure
Fuel
105.8 28 US gal 23 1/4 Imp gal
Engine oil
Drain and refillWith oil filter change
6.2 6 1/2 qt 5 1/2 qt
Without oil filter change
5.9 6 1/4 qt 5 1/4 qt
Dry engine (engine overhaul)
7.6 8 qt 6 3/4 qt
Cooling system With reservoir at MAX level
14.4 3 3/4 gal 3 1/8 gal
Automatic transmission fluid (ATF)
10.6 11 1/4 qt 9 3/8 qt
Rear final drive oil
1.75 3 3/4 pt 3 1/8 pt
Transfer fluid
3.0 3 1/8 qt 2 5/8 qt
Front final drive oil
1.6 3 3/8 pt 2 7/8 pt
Power steering fluid (PSF)
1.0 2 1/8 pt 1 3/4 pt
Windshield washer fluid
4.5 1 1/4 gal 1 gal
Air conditioning system refrigerant 1.08 ± 0.05 kg 2.38 ± 0.11 lb 2.38 ± 0.11 lb
Air conditioning system lubricants
290 m9.8 fl oz 10.2 fl oz

ACS-12
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: October 20052005 QX56
LASER BEAM AIMING ADJUSTMENTPFP:00026
Outline of Laser Beam Aiming Adjustment ProcedureEKS00BLN
CAUTION:

The laser beam aiming adjustment cannot be performed without CONSULT-II.

The laser beam aiming adjustment must be performed every time the ICC sensor is removed,
installed or has been moved as a result of a collision.
1. Prepare the vehicle and the work area.
2. Set up the ICC target board.
3. Adjust the sensor following the procedure on CONSULT-II.
4. Check system operation after the adjustment.
PreparationEKS00BLO

Place the vehicle on level ground. Shift the transmission into "P" position and release the parking brake.

Adjust the tire pressure to the specified value.

See that there is no load in the vehicle. Coolant, engine oil and fuel should be filled to correct level.

Check that the vehicle suspension has been adjusted to the standard height by the load leveling rear air
suspension system. Refer to RSU-12, "
Basic Inspection" .

Clean the sensor with a soft cloth.
Setting up the ICC Target BoardEKS00BLP
CAUTION:
Accuracy in setting up the ICC target board is essential for the laser beam aiming adjustment.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale as shown.Tool number : KV99110100 (J-45718)
LKIA0632E
WKIA1849E

ACS-46
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: October 20052005 QX56
11 . CHECK HARNESS THROUGH ICC UNIT, ICC BRAKE HOLD RELAY, AND GROUND
1. Disconnect ICC unit and ICC brake hold relay harness connec-
tors.
2. Check continuity between ICC unit harness connector B17 ter-
minal 47 (BR) and ICC brake hold relay harness connector E134
terminal 1 (BR).
3. Check continuity between ICC unit harness connector B17 ter-
minal 47 (BR) and ground.
4. Check continuity between ICC brake hold relay harness connec-
tor E134 terminal 2 (B) and ground.
OK or NG
OK >> GO TO 12.
NG >>

Repair harness through ICC unit and ICC brake hold
relay, or between ICC brake hold relay and ground.

Erase DTC and perform ICC system running test.
Refer to ACS-9, "
ICC System Running Test" . Then
perform self-diagnosis of ICC system again.
12. CHECK ICC BRAKE HOLD RELAY
Check continuity between ICC brake hold relay terminal 1 and termi-
nal 2.
OK or NG
OK >> GO TO 13.
NG >> Replace ICC brake hold relay. Erase DTC and perform
ICC system running test. Refer to ACS-9, "
ICC System
Running Test" . Then perform self-diagnosis of ICC sys-
tem again.
13. CHECK ICC UNIT STANDARD VOLTAGE
With CONSULT-II
1. Connect connectors of ICC unit and stop lamp switch.
2. While performing active test (STOP LAMP: STP LMP DRIVE
ON) with CONSULT-II, check voltage between ICC unit harness
connector B17 terminal 47 (BR) and ground.
OK or NG
OK >> GO TO 14.
NG >> Replace ICC unit. Refer to ACS-60, "
ICC Unit" . Erase
DTC and perform ICC system running test. Refer to
ACS-9, "
ICC System Running Test" . Then perform self-
diagnosis of ICC system again. 47 - 1 Continuity should exist.
47 - Ground Continuity should not exist.
SKIA6660E
Continuity should exist.
SKIA6661E
Continuity should exist
(minimal resistance through coil will exist)
SKIA6662E
47 - Ground Battery voltage should exist
(during active test)
SKIA3075E

AT-4Revision: October 20052005 QX56 A/T Does Not Shift: D
3 → D4 ................................199
A/T Does Not Shift: D
4 → D5 ................................202
A/T Does Not Perform Lock-up ............................204
A/T Does Not Hold Lock-up Condition ..................206
Lock-up Is Not Released ......................................208
Engine Speed Does Not Return to Idle ................209
A/T Does Not Shift: 5th gear → 4th gear ..............210
A/T Does Not Shift: 4th gear → 3rd gear ..............213
A/T Does Not Shift: 3rd gear → 2nd gear .............214
A/T Does Not Shift: 2nd gear → 1st gear .............216
Vehicle Does Not Decelerate By Engine Brake ....219
A/T SHIFT LOCK SYSTEM .....................................222
Description ............................................................222
Shift Lock System Electrical Parts Location .........222
Wiring Diagram — A/T — SHIFT ..........................223
Shift Lock Control Unit Reference Values .............224
Component Inspection ..........................................225
SHIFT CONTROL SYSTEM ....................................227
Control Device Removal and Installation ..............227
Adjustment of A/T Position ...................................228
Checking of A/T Position ......................................228
ON-VEHICLE SERVICE ..........................................229
Oil Pan ..................................................................229
Control Valve With TCM and A/T Fluid Temperature
Sensor 2 ...............................................................231
Rear Oil Seal ........................................................241
AIR BREATHER HOSE ...........................................242
Removal and Installation ......................................242
TRANSMISSION ASSEMBLY ................................244
Removal and Installation (4x2) .............................244
Removal and Installation (4x4) .............................247
OVERHAUL .............................................................250Components .......................................................... 250
Oil Channel ........................................................... 258
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings .......................... 260
DISASSEMBLY ....................................................... 262
Disassembly .......................................................... 262
REPAIR FOR COMPONENT PARTS ...................... 280
Oil Pump ............................................................... 280
Front Sun Gear, 3rd One-Way Clutch ................... 282
Front Carrier, Input Clutch, Rear Internal Gear ..... 284
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub .............................................. 289
High and Low Reverse Clutch .............................. 294
Direct Clutch ......................................................... 296
ASSEMBLY ............................................................. 298
Assembly (1) ......................................................... 298
Adjustment ............................................................311
Assembly (2) ......................................................... 314
SERVICE DATA AND SPECIFICATIONS (SDS) .... 321
General Specifications .......................................... 321
Vehicle Speed When Shifting Gears ..................... 321
Vehicle Speed When Performing and Releasing
Complete Lock-up ................................................. 322
Vehicle Speed When Performing and Releasing
Slip Lock-up .......................................................... 322
Stall Speed ............................................................ 322
Line Pressure ........................................................ 322
A/T Fluid Temperature Sensor .............................. 322
Turbine Revolution Sensor .................................... 322
Vehicle Speed Sensor A/T (Revolution Sensor) ... 322
Reverse brake ....................................................... 323
Total End Play ....................................................... 323

AT-8
PRECAUTIONS
Revision: October 20052005 QX56
Precautions ECS00CDL

Before connecting or disconnecting the A/T assembly har-
ness connector, turn ignition switch “OFF” and disconnect
negative battery cable. Because battery voltage is applied
to TCM even if ignition switch is turned “OFF”.

After performing each TROUBLE DIAGNOSIS, perform
“DTC (Diagnostic Trouble Code) CONFIRMATION PROCE-
DURE”.
If the repair is completed the DTC should not be displayed
in the “DTC CONFIRMATION PROCEDURE”.

Always use the specified brand of ATF. Refer to MA-11, "RECOMMENDED FLUIDS AND LUBRICANTS" .

Use paper rags not cloth rags during work.

After replacing the ATF, dispose of the waste oil using the methods prescribed by law, ordinance, etc.

Before proceeding with disassembly, thoroughly clean the outside of the transmission. It is important to
prevent the internal parts from becoming contaminated by dirt or other foreign matter.

Disassembly should be done in a clean work area.

Use lint-free cloth or towels for wiping parts clean. Common shop rags can leave fibers that could interfere
with the operation of the transmission.

Place disassembled parts in order for easier and proper assembly.

All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or
reassembly.

Gaskets, seals and O-rings should be replaced any time the transmission is disassembled.

It is very important to perform functional tests whenever they are indicated.

The valve body contains precision parts and requires extreme care when parts are removed and serviced.
Place disassembled valve body parts in order for easier and proper assembly. Care will also prevent
springs and small parts from becoming scattered or lost.

Properly installed valves, sleeves, plugs, etc. will slide along bores in valve body under their own weight.

Before assembly, apply a coat of recommended ATF to all parts. Apply petroleum jelly to protect O-rings
and seals, or hold bearings and washers in place during assembly. Do not use grease.

Extreme care should be taken to avoid damage to O-rings, seals and gaskets when assembling.

Clean or replace ATF cooler if excessive foreign material is found in oil pan or clogging strainer. Refer to
AT- 1 3 , "
A/T Fluid Cooler Cleaning" .

After overhaul, refill the transmission with new ATF.

When the A/T drain plug is removed, only some of the fluid is drained. Old A/T fluid will remain in torque
converter and ATF cooling system.
Always follow the procedures under “Changing A/T Fluid” in the AT section when changing A/T fluid. Refer
to AT-13, "
Changing A/T Fluid" , AT-13, "Checking A/T Fluid" .
SEF 2 89 H
SEF 2 17 U

AT-10
PREPARATION
Revision: October 20052005 QX56
PREPARATIONPFP:00002
Special Service ToolsECS00CDO
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
ST2505S001
(J-34301-C)
Oil pressure gauge set
1 ST25051001
(—)
Oil pressure gauge
2 ST25052000
(—)
Hose
3 ST25053000
(—)
Joint pipe
4 ST25054000
(—)
Adapter
5 ST25055000
(—)
AdapterMeasuring line pressure
KV31103600
(J-45674)
Joint pipe adapter
(With ST25054000)Measuring line pressure
ST33400001
(J-26082)
Drift

Installing rear oil seal (2WD models)

Installing oil pump housing oil seal
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
KV31102400
(J-34285 and J-34285-87)
Clutch spring compressorInstalling reverse brake return spring retainer
a: 320 mm (12.60 in)
b: 174 mm (6.85 in)
ST25850000
(J-25721-A)
Sliding hammerRemove oil pump assembly
a: 179 mm (7.05 in)
b: 70 mm (2.76 in)
c: 40 mm (1.57 in)
d: M12X1.75P
ZZA0600D
ZZA1227D
NT086
NT423
NT422